diff options
Diffstat (limited to 'functest/opnfv_tests/vnf/epc/featureFiles/Attach_Procedure_With_P_CSCF_Addr_Request.feature')
| -rw-r--r-- | functest/opnfv_tests/vnf/epc/featureFiles/Attach_Procedure_With_P_CSCF_Addr_Request.feature | 44 |
1 files changed, 44 insertions, 0 deletions
diff --git a/functest/opnfv_tests/vnf/epc/featureFiles/Attach_Procedure_With_P_CSCF_Addr_Request.feature b/functest/opnfv_tests/vnf/epc/featureFiles/Attach_Procedure_With_P_CSCF_Addr_Request.feature new file mode 100644 index 000000000..605bb934f --- /dev/null +++ b/functest/opnfv_tests/vnf/epc/featureFiles/Attach_Procedure_With_P_CSCF_Addr_Request.feature @@ -0,0 +1,44 @@ +############################################################################################################################ +# Date: <22/08/2016> Version: <1.1> # +############################################################################################################################ + +Feature: Attach Procedure With P-CSCF Address Request Indication in PCO + +@attach-procedure @TS_24_301 @24_301_5_5 @24_301_5_5_1_2_2 @TS_24_368 @24_368_4 @24_368-5_4 @Series-0000 +@TS_36_523_9_2_1_1_3 @Attach_Procedure_P-CSCF_Address_Request @PCO + +Scenario: Attach Procedure indicating a request for P-CSCF address in the protocol configuration options + +Given all configured endpoints for SSH are connected successfully + +Given the steps below will be executed at the end +When I stop S1AP simulator on node ABOT +When I run the SSH command "sudo service mme_gw restart" on node MME +Given the execution is paused for {abotprop.WAIT_10_SEC} seconds +Then the ending steps are complete + +# Set ABOT configuration +Given that I setup S1AP Simulator with default parameters specified in {abotprop.ABOT.EPC.Defaults} on node ABOT +Given that I setup S1AP Simulator with USIM parameter "ABOT.UE.USIM.AttachWithImsi=true" on node ABOT + +Given that I setup S1AP Simulator with UE parameter "ABOT.UE.CONFIG.PCO.IPV6_P_CSCF_ADDR_REQ=true" on node ABOT + +# Execute ABOT S1AP Simulator +When I run S1AP simulator on node ABOT with 1 UE + +# Wait for execution to complete before checking results +Given the execution is paused for {abotprop.WAIT_10_SEC} seconds + +# Validate Test Case Execution at Simulator +Then I receive S1AP response on node ABOT and verify the presence of all the following values: +| responseResult | existence | +| Send Attach Request message with IMSI | {string:nocase:present} | +| Send PDN Connectivity Request message with P-CSCF Address Request | {string:nocase:present} | +| Received Authentication Request message | {string:nocase:present} | +| Send Authentication Response message | {string:nocase:present} | +| Received Authentication Request message | {string:nocase:present} | +| Send Authentication Response message | {string:nocase:present} | +| Received Security Mode Command message | {string:nocase:present} | +| Send Security Mode Complete message | {string:nocase:present} | +| Received Attach Accept message | {string:nocase:present} | +| Received Activate Default EPS Bearer Context Request message with PCO contain Protocol ID 0001 | {string:nocase:present} | |