Merge "Document for Euphrates test case results" into stable/fraser

1 files changed, 0 insertions, 517 deletions

diff --git a/docs/release/results/os-onos-sfc-ha.rst b/docs/release/results/os-onos-sfc-ha.rst
deleted file mode 100644
index e52ae3d55..000000000
--- a/docs/release/results/os-onos-sfc-ha.rst
+++ /dev/null
@@ -1,517 +0,0 @@
-.. This work is licensed under a Creative Commons Attribution 4.0 International
-.. License.
-.. http://creativecommons.org/licenses/by/4.0
-
-
-===============================
-Test Results for os-onos-sfc-ha
-===============================
-
-.. toctree::
-   :maxdepth: 2
-
-
-fuel
-====
-
-.. _Grafana: http://testresults.opnfv.org/grafana/dashboard/db/yardstick-main
-.. _POD2: https://wiki.opnfv.org/pharos?&#community_test_labs
-
-Overview of test results
-------------------------
-
-See Grafana_ for viewing test result metrics for each respective test case. It
-is possible to chose which specific scenarios to look at, and then to zoom in
-on the details of each run test scenario as well.
-
-All of the test case results below are based on 4 scenario test runs, each run
-on the Ericsson POD2_ or LF POD2_ between September 5 and 10 in 2016.
-
-TC002
------
-The round-trip-time (RTT) between 2 VMs on different blades is measured using
-ping. Most test run measurements result on average between 0.5 and 0.6 ms.
-A few runs start with a 1 - 1.5 ms RTT spike (This could be because of normal ARP
-handling). One test run has a greater RTT spike of 1.9 ms, which is the same
-one with the 0.7 ms average. The other runs have no similar spike at all.
-To be able to draw conclusions more runs should be made.
-SLA set to 10 ms. The SLA value is used as a reference, it has not
-been defined by OPNFV.
-
-TC005
------
-The IO read bandwidth looks similar between different dates, with an
-average between approx. 170 and 200 MB/s. Within each test run the results
-vary, with a minimum 2 MB/s and maximum 838 MB/s on the totality. Most runs
-have a minimum BW of 3 MB/s (two runs at 2 MB/s). The maximum BW varies more in
-absolute numbers between the dates, between 617 and 838 MB/s.
-SLA set to 400 MB/s. The SLA value is used as a reference, it has not been
-defined by OPNFV.
-
-TC010
------
-The measurements for memory latency are similar between test dates and result
-in approx. 1.2 ns. The variations within each test run are similar, between
-1.215 and 1.219 ns. One exception is February 16, where the average is 1.222
-and varies between 1.22 and 1.28 ns.
-SLA set to 30 ns. The SLA value is used as a reference, it has not been defined
-by OPNFV.
-
-TC011
------
-Packet delay variation between 2 VMs on different blades is measured using
-Iperf3. On the first date the reported packet delay variation varies between
-0.0025 and 0.011 ms, with an average delay variation of 0.0067 ms.
-On the second date the delay variation varies between 0.002 and 0.006 ms, with
-an average delay variation of 0.004 ms.
-
-TC012
------
-Between test dates, the average measurements for memory bandwidth vary between
-17.4 and 17.9 GB/s. Within each test run the results vary more, with a minimal
-BW of 16.4 GB/s and maximum of 18.2 GB/s on the totality.
-SLA set to 15 GB/s. The SLA value is used as a reference, it has not been
-defined by OPNFV.
-
-TC014
------
-The Unixbench processor test run results vary between scores 3080 and 3240,
-one result each date. The average score on the total is 3150.
-No SLA set.
-
-TC037
------
-The amount of packets per second (PPS) and round trip times (RTT) between 2 VMs
-on different blades are measured when increasing the amount of UDP flows sent
-between the VMs using pktgen as packet generator tool.
-
-Round trip times and packet throughput between VMs can typically be affected by
-the amount of flows set up and result in higher RTT and less PPS throughput.
-
-The RTT results are similar throughout the different test dates and runs at
-approx. 15 ms. Some test runs show an increase with many flows, in the range
-towards 16 to 17 ms. One exception standing out is Feb. 15 where the average
-RTT is stable at approx. 13 ms. The PPS results are not as consistent as the
-RTT results.
-In some test runs when running with less than approx. 10000 flows the PPS
-throughput is normally flatter compared to when running with more flows, after
-which the PPS throughput decreases. Around 20 percent decrease in the worst
-case. For the other test runs there is however no significant change to the PPS
-throughput when the number of flows are increased. In some test runs the PPS
-is also greater with 1000000 flows compared to other test runs where the PPS
-result is less with only 2 flows.
-
-The average PPS throughput in the different runs varies between 414000 and
-452000 PPS. The total amount of packets in each test run is approx. 7500000 to
-8200000 packets. One test run Feb. 15 sticks out with a PPS average of
-558000 and approx. 1100000 packets in total (same as the on mentioned earlier
-for RTT results).
-
-There are lost packets reported in most of the test runs. There is no observed
-correlation between the amount of flows and the amount of lost packets.
-The lost amount of packets normally range between 100 and 1000 per test run,
-but there are spikes in the range of 10000 lost packets as well, and even
-more in a rare cases.
-
-CPU utilization statistics are collected during UDP flows sent between the VMs
-using pktgen as packet generator tool. The average measurements for CPU
-utilization ratio vary between 1% to 2%. The peak of CPU utilization ratio
-appears around 7%.
-
-TC069
------
-Between test dates, the average measurements for memory bandwidth vary between
-15.5 and 25.4 GB/s. Within each test run the results vary more, with a minimal
-BW of 9.7 GB/s and maximum of 29.5 GB/s on the totality.
-SLA set to 6 GB/s. The SLA value is used as a reference, it has not been
-defined by OPNFV.
-
-TC070
------
-The amount of packets per second (PPS) and round trip times (RTT) between 2 VMs
-on different blades are measured when increasing the amount of UDP flows sent
-between the VMs using pktgen as packet generator tool.
-
-Round trip times and packet throughput between VMs can typically be affected by
-the amount of flows set up and result in higher RTT and less PPS throughput.
-
-The RTT results are similar throughout the different test dates and runs at
-approx. 15 ms. Some test runs show an increase with many flows, in the range
-towards 16 to 17 ms. One exception standing out is Feb. 15 where the average
-RTT is stable at approx. 13 ms. The PPS results are not as consistent as the
-RTT results.
-In some test runs when running with less than approx. 10000 flows the PPS
-throughput is normally flatter compared to when running with more flows, after
-which the PPS throughput decreases. Around 20 percent decrease in the worst
-case. For the other test runs there is however no significant change to the PPS
-throughput when the number of flows are increased. In some test runs the PPS
-is also greater with 1000000 flows compared to other test runs where the PPS
-result is less with only 2 flows.
-
-The average PPS throughput in the different runs varies between 414000 and
-452000 PPS. The total amount of packets in each test run is approx. 7500000 to
-8200000 packets. One test run Feb. 15 sticks out with a PPS average of
-558000 and approx. 1100000 packets in total (same as the on mentioned earlier
-for RTT results).
-
-There are lost packets reported in most of the test runs. There is no observed
-correlation between the amount of flows and the amount of lost packets.
-The lost amount of packets normally range between 100 and 1000 per test run,
-but there are spikes in the range of 10000 lost packets as well, and even
-more in a rare cases.
-
-Memory utilization statistics are collected during UDP flows sent between the
-VMs using pktgen as packet generator tool. The average measurements for memory
-utilization vary between 225MB to 246MB. The peak of memory utilization appears
-around 340MB.
-
-TC071
------
-The amount of packets per second (PPS) and round trip times (RTT) between 2 VMs
-on different blades are measured when increasing the amount of UDP flows sent
-between the VMs using pktgen as packet generator tool.
-
-Round trip times and packet throughput between VMs can typically be affected by
-the amount of flows set up and result in higher RTT and less PPS throughput.
-
-The RTT results are similar throughout the different test dates and runs at
-approx. 15 ms. Some test runs show an increase with many flows, in the range
-towards 16 to 17 ms. One exception standing out is Feb. 15 where the average
-RTT is stable at approx. 13 ms. The PPS results are not as consistent as the
-RTT results.
-In some test runs when running with less than approx. 10000 flows the PPS
-throughput is normally flatter compared to when running with more flows, after
-which the PPS throughput decreases. Around 20 percent decrease in the worst
-case. For the other test runs there is however no significant change to the PPS
-throughput when the number of flows are increased. In some test runs the PPS
-is also greater with 1000000 flows compared to other test runs where the PPS
-result is less with only 2 flows.
-
-The average PPS throughput in the different runs varies between 414000 and
-452000 PPS. The total amount of packets in each test run is approx. 7500000 to
-8200000 packets. One test run Feb. 15 sticks out with a PPS average of
-558000 and approx. 1100000 packets in total (same as the on mentioned earlier
-for RTT results).
-
-There are lost packets reported in most of the test runs. There is no observed
-correlation between the amount of flows and the amount of lost packets.
-The lost amount of packets normally range between 100 and 1000 per test run,
-but there are spikes in the range of 10000 lost packets as well, and even
-more in a rare cases.
-
-Cache utilization statistics are collected during UDP flows sent between the
-VMs using pktgen as packet generator tool. The average measurements for cache
-utilization vary between 205MB to 212MB.
-
-TC072
------
-The amount of packets per second (PPS) and round trip times (RTT) between 2 VMs
-on different blades are measured when increasing the amount of UDP flows sent
-between the VMs using pktgen as packet generator tool.
-
-Round trip times and packet throughput between VMs can typically be affected by
-the amount of flows set up and result in higher RTT and less PPS throughput.
-
-The RTT results are similar throughout the different test dates and runs at
-approx. 15 ms. Some test runs show an increase with many flows, in the range
-towards 16 to 17 ms. One exception standing out is Feb. 15 where the average
-RTT is stable at approx. 13 ms. The PPS results are not as consistent as the
-RTT results.
-In some test runs when running with less than approx. 10000 flows the PPS
-throughput is normally flatter compared to when running with more flows, after
-which the PPS throughput decreases. Around 20 percent decrease in the worst
-case. For the other test runs there is however no significant change to the PPS
-throughput when the number of flows are increased. In some test runs the PPS
-is also greater with 1000000 flows compared to other test runs where the PPS
-result is less with only 2 flows.
-
-The average PPS throughput in the different runs varies between 414000 and
-452000 PPS. The total amount of packets in each test run is approx. 7500000 to
-8200000 packets. One test run Feb. 15 sticks out with a PPS average of
-558000 and approx. 1100000 packets in total (same as the on mentioned earlier
-for RTT results).
-
-There are lost packets reported in most of the test runs. There is no observed
-correlation between the amount of flows and the amount of lost packets.
-The lost amount of packets normally range between 100 and 1000 per test run,
-but there are spikes in the range of 10000 lost packets as well, and even
-more in a rare cases.
-
-Network utilization statistics are collected during UDP flows sent between the
-VMs using pktgen as packet generator tool. Total number of packets received per
-second was average on 200 kpps and total number of packets transmitted per
-second was average on 600 kpps.
-
-Detailed test results
----------------------
-The scenario was run on Ericsson POD2_ and LF POD2_ with:
-Fuel 9.0
-OpenStack Mitaka
-Onos Goldeneye
-OpenVirtualSwitch 2.5.90
-OpenDayLight Beryllium
-
-Rationale for decisions
------------------------
-Pass
-
-Tests were successfully executed and metrics collected.
-No SLA was verified. To be decided on in next release of OPNFV.
-
-Conclusions and recommendations
--------------------------------
-The pktgen test configuration has a relatively large base effect on RTT in
-TC037 compared to TC002, where there is no background load at all. Approx.
-15 ms compared to approx. 0.5 ms, which is more than a 3000 percentage
-difference in RTT results.
-Especially RTT and throughput come out with better results than for instance
-the *fuel-os-nosdn-nofeature-ha* scenario does. The reason for this should
-probably be further analyzed and understood. Also of interest could be
-to make further analyzes to find patterns and reasons for lost traffic.
-Also of interest could be to see if there are continuous variations where
-some test cases stand out with better or worse results than the general test
-case.
-
-
-Joid
-=====
-
-.. _Grafana: http://testresults.opnfv.org/grafana/dashboard/db/yardstick-main
-.. _POD6: https://wiki.opnfv.org/pharos?&#community_test_labs
-
-Overview of test results
-------------------------
-
-See Grafana_ for viewing test result metrics for each respective test case. It
-is possible to chose which specific scenarios to look at, and then to zoom in
-on the details of each run test scenario as well.
-
-All of the test case results below are based on 4 scenario test runs, each run
-on the Intel POD6_ between September 8 and 11 in 2016.
-
-TC002
------
-The round-trip-time (RTT) between 2 VMs on different blades is measured using
-ping. Most test run measurements result on average between 1.35 ms and 1.57 ms.
-Only one test run has reached greatest RTT spike of 2.58 ms. Meanwhile, the
-smallest network latency is 1.11 ms, which is obtained on Sep. 11st. In
-general, the average of network latency of the four test runs are between 1.35
-ms and 1.57 ms. SLA set to be 10 ms. The SLA value is used as a reference, it
-has not been defined by OPNFV.
-
-TC005
------
-The IO read bandwidth actually refers to the storage throughput, which is
-measured by fio and the greatest IO read bandwidth of the four runs is 175.4
-MB/s. The IO read bandwidth of the three runs looks similar, with an average
-between 43.7 and 56.3 MB/s, except one on Sep. 8, for its maximum storage
-throughput is only 107.9 MB/s. One of the runs has a minimum BW of 478 KM/s and
-other has a maximum BW of 168.6 MB/s. The SLA of read bandwidth sets to be
-400 MB/s, which is used as a reference, and it has not been defined by OPNFV.
-
-The results of storage IOPS for the four runs look similar with each other. The
-IO read times per second of the four test runs have an average value between
-978 per second and 1.20 K/s, and meanwhile, the minimum result is only 36 times
-per second.
-
-TC010
------
-The tool we use to measure memory read latency is lmbench, which is a series of
-micro benchmarks intended to measure basic operating system and hardware system
-metrics. The memory read latency of the four runs is between 1.164 ns and 1.244
-ns on average. The variations within each test run are quite different, some
-vary from a large range and others have a small change. For example, the
-largest change is on September 10, the memory read latency of which is ranging
-from 1.128 ns to 1.381 ns. However, the results on September 11 change very
-little. The SLA sets to be 30 ns. The SLA value is used as a reference, it has
-not been defined by OPNFV.
-
-TC011
------
-Iperf3 is a tool for evaluating the packet delay variation between 2 VMs on
-different blades. The reported packet delay variations of the four test runs
-differ from each other. In general, the packet delay of two runs look similar,
-for they both stay stable within each run. And the mean packet delay of them
-are 0.0772 ms and 0.0788 ms respectively. Of the four runs, the fourth has the
-worst result, because the packet delay reaches 0.0838 ms. The rest one has a
-large wide range from 0.0666 ms to 0.0798 ms. The SLA value sets to be 10 ms.
-The SLA value is used as a reference, it has not been defined by OPNFV.
-
-TC012
------
-Lmbench is also used to measure the memory read and write bandwidth, in which
-we use bw_mem to obtain the results. Among the four test runs, the trend of the
-memory bandwidth almost look similar, which all have a large wide range, and
-the minimum and maximum results are 9.02 GB/s and 18.14 GB/s. Here SLA set to
-be 15 GB/s. The SLA value is used as a reference, it has not been defined by
-OPNFV.
-
-TC014
------
-The Unixbench is used to evaluate the IaaS processing speed with regards to
-score of single cpu running and parallel running. It can be seen from the
-dashboard that the processing test results vary from scores 3395 to 3475, and
-there is only one result one date. No SLA set.
-
-TC037
------
-The amount of packets per second (PPS) and round trip times (RTT) between 2 VMs
-on different blades are measured when increasing the amount of UDP flows sent
-between the VMs using pktgen as packet generator tool.
-
-Round trip times and packet throughput between VMs can typically be affected by
-the amount of flows set up and result in higher RTT and less PPS throughput.
-
-The mean packet throughput of the four test runs is between 362.1 kpps and
-363.5 kpps, of which the result of the third run is the highest. The RTT
-results of all the test runs keep flat at approx. 17 ms. It is obvious that the
-PPS results are not as consistent as the RTT results.
-
-The No. flows of the four test runs are 240 k on average and the PPS results
-look a little waved since the largest packet throughput is 418.1 kpps and the
-minimum throughput is 326.5 kpps respectively.
-
-There are no errors of packets received in the four runs, but there are still
-lost packets in all the test runs. The RTT values obtained by ping of the four
-runs have the similar average vaue, that is approx. 17 ms, of which the worst
-RTT is 39 ms on Sep. 11st.
-
-CPU load is measured by mpstat, and CPU load of the four test runs seem a
-little similar, since the minimum value and the peak of CPU load is between 0
-percent and nine percent respectively. And the best result is obtained on Sep.
-10, with an CPU load of nine percent.
-
-TC069
------
-With the block size changing from 1 kb to 512 kb, the memory write bandwidth
-tends to become larger first and then smaller within every run test, which
-rangs from 25.9 GB/s to 26.6 GB/s and then to 18.1 GB/s on average. Since the
-test id is one, it is that only the INT memory write bandwidth is tested. On
-the whole, when the block size is from 2 kb to 16 kb, the memory write
-bandwidth look similar with a minimal BW of 22.1 GB/s and peak value of 28.6
-GB/s. And then with the block size becoming larger, the memory write bandwidth
-tends to decrease. SLA sets to be 7 GB/s. The SLA value is used as a reference,
-it has not been defined by OPNFV.
-
-TC070
------
-The amount of packets per second (PPS) and round trip times (RTT) between 2 VMs
-on different blades are measured when increasing the amount of UDP flows sent
-between the VMs using pktgen as packet generator tool.
-
-Round trip times and packet throughput between VMs can typically be affected by
-the amount of flows set up and result in higher RTT and less PPS throughput.
-
-The network latency is measured by ping, and the results of the four test runs
-look similar with each other, and within these test runs, the maximum RTT can
-reach 39 ms and the average RTT is usually approx. 17 ms. The network latency
-tested on Sep. 11 shows that it has a peak latency of 39 ms. But on the whole,
-the average RTTs of the five runs keep flat and the network latency is
-relatively short.
-
-Memory utilization is measured by free, which can display amount of free and
-used memory in the system. The largest amount of used memory is 270 MiB on the
-first two runs. In general, the mean used memory of two test runs have very
-large memory utilization, which can reach 264 MiB on average. And the other two
-runs have a large wide range of memory usage with the minimum value of 150 MiB
-and the maximum value of 270 MiB. On the other hand, for the mean free memory,
-the four test runs have the similar trend with that of the mean used memory.
-In general, the mean free memory change from 220 MiB to 342 MiB.
-
-Packet throughput and packet loss can be measured by pktgen, which is a tool
-in the network for generating traffic loads for network experiments. The mean
-packet throughput of the four test runs seem quite different, ranging from
-326.5 kpps to 418.1 kpps. The average number of flows in these tests is
-240000, and each run has a minimum number of flows of 2 and a maximum number
-of flows of 1.001 Mil. At the same time, the corresponding packet throughput
-differ between 326.5 kpps and 418.1 kpps with an average packet throughput between
-361.7 kpps and 363.5 kpps. In summary, the PPS results seem consistent. Within each
-test run of the four runs, when number of flows becomes larger, the packet
-throughput seems not larger at the same time.
-
-TC071
------
-The amount of packets per second (PPS) and round trip times (RTT) between 2 VMs
-on different blades are measured when increasing the amount of UDP flows sent
-between the VMs using pktgen as packet generator tool.
-
-Round trip times and packet throughput between VMs can typically be affected by
-the amount of flows set up and result in higher RTT and less PPS throughput.
-
-The network latency is measured by ping, and the results of the four test runs
-look similar with each other. Within each test run, the maximum RTT is only 47
-ms and the average RTT is usually approx. 15 ms. On the whole, the average
-RTTs of the four runs keep stable and the network latency is relatively small.
-
-Cache utilization is measured by cachestat, which can display size of cache and
-buffer in the system. Cache utilization statistics are collected during UDP
-flows sent between the VMs using pktgen as packet generator tool. The largest
-cache size is 214 MiB, which is same for the four runs, and the smallest cache
-size is 94 MiB. On the whole, the average cache size of the four runs look the
-same and is between 198 MiB and 207 MiB. Meanwhile, the tread of the buffer
-size keep flat, since they have a minimum value of 7 MiB and a maximum value of
-8 MiB, with an average value of about 7.9 MiB.
-
-Packet throughput can be measured by pktgen, which is a tool in the network for
-generating traffic loads for network experiments. The mean packet throughput of
-the four test runs seem quite the same, which is approx. 363 kpps. The average
-number of flows in these tests is 240k, and each run has a minimum number of
-flows of 2 and a maximum number of flows of 1.001 Mil. At the same time, the
-corresponding packet throughput differ between 327 kpps and 418 kpps with an
-average packet throughput of about 363 kpps. Within each test run of the four
-runs, when number of flows becomes larger, the packet throughput seems not
-larger in the meantime.
-
-TC072
------
-The amount of packets per second (PPS) and round trip times (RTT) between 2 VMs
-on different blades are measured when increasing the amount of UDP flows sent
-between the VMs using pktgen as packet generator tool.
-
-Round trip times and packet throughput between VMs can typically be affected by
-the amount of flows set up and result in higher RTT and less PPS throughput.
-
-The RTT results are similar throughout the different test dates and runs
-between 0 ms and 47 ms with an average leatency of less than 16 ms. The PPS
-results are not as consistent as the RTT results, for the mean packet
-throughput of the four runs differ from 361.7 kpps to 365.0 kpps.
-
-Network utilization is measured by sar, that is system activity reporter, which
-can display the average statistics for the time since the system was started.
-Network utilization statistics are collected during UDP flows sent between the
-VMs using pktgen as packet generator tool. The largest total number of packets
-transmitted per second look similar for two test runs, whose values change a
-lot from 10 pps to 432 kpps. While results of the other test runs seem the same
-and keep stable with the average number of packets transmitted per second of 10
-pps. However, the total number of packets received per second of the four runs
-look similar, which have a large wide range of 2 pps to 657 kpps.
-
-In some test runs when running with less than approx. 250000 flows the PPS
-throughput is normally flatter compared to when running with more flows, after
-which the PPS throughput decreases. For the other test runs there is however no
-significant change to the PPS throughput when the number of flows are
-increased. In some test runs the PPS is also greater with 250000 flows
-compared to other test runs where the PPS result is less with only 2 flows.
-
-There are lost packets reported in most of the test runs. There is no observed
-correlation between the amount of flows and the amount of lost packets.
-The lost amount of packets normally differs a lot per test run.
-
-Detailed test results
----------------------
-The scenario was run on Intel POD6_ with:
-Joid
-OpenStack Mitaka
-Onos Goldeneye
-OpenVirtualSwitch 2.5.90
-OpenDayLight Beryllium
-
-Rationale for decisions
------------------------
-Pass
-
-Conclusions and recommendations
--------------------------------
-Tests were successfully executed and metrics collected.
-No SLA was verified. To be decided on in next release of OPNFV.
-