summaryrefslogtreecommitdiffstats
path: root/docs/requirements
diff options
context:
space:
mode:
Diffstat (limited to 'docs/requirements')
-rw-r--r--docs/requirements/vswitchperf_ltd.rst122
1 files changed, 122 insertions, 0 deletions
diff --git a/docs/requirements/vswitchperf_ltd.rst b/docs/requirements/vswitchperf_ltd.rst
index 6b882290..9e26f637 100644
--- a/docs/requirements/vswitchperf_ltd.rst
+++ b/docs/requirements/vswitchperf_ltd.rst
@@ -1947,6 +1947,128 @@ Test ID: LTD.Throughput.Overlay.Network.<tech>.RFC2544.PacketLossRatio
- CPU and memory utilization may also be collected as part of this
test, to determine the vSwitch's performance footprint on the system.
+.. 3.2.3.1.15
+
+Test ID: LTD.Throughput.RFC2544.MatchAction.PacketLossRatio
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ **Title**: RFC 2544 X% packet loss ratio match action Throughput and Latency Test
+
+ **Prerequisite Test**: LTD.Throughput.RFC2544.PacketLossRatio
+
+ **Priority**:
+
+ **Description**:
+
+ The aim of this test is to determine the cost of carrying out match
+ action(s) on the DUT’s RFC2544 Throughput with X% traffic loss for
+ a constant load (fixed length frames at a fixed interval time).
+
+ Each test case requires:
+ * selection of a specific match action(s),
+ * specifying a percentage of total traffic that is elligible
+ for the match action,
+ * determination of the specific test configuration (number
+ of flows, number of test ports, presence of an external
+ controller, etc.), and
+ * measurement of the RFC 2544 Throughput level with X% packet
+ loss: Traffic shall be bi-directional and symmetric.
+
+ Note: It would be ideal to verify that all match action-elligible
+ traffic was forwarded to the correct port, and if forwarded to
+ an unintended port it should be considered lost.
+
+ A match action is an action that is typically carried on a frame
+ or packet that matches a set of flow classification parameters
+ (typically frame/packet header fields). A match action may or may
+ not modify a packet/frame. Match actions include [1]:
+ * output : outputs a packet to a particular port.
+ * normal: Subjects the packet to traditional L2/L3 processing
+ (MAC learning).
+ * flood: Outputs the packet on all switch physical ports
+ other than the port on which it was received and any ports
+ on which flooding is disabled.
+ * all: Outputs the packet on all switch physical ports other
+ than the port on which it was received.
+ * local: Outputs the packet on the ``local port,'' which
+ corresponds to the network device that has the same name as
+ the bridge.
+ * in_port: Outputs the packet on the port from which it was
+ received.
+ * Controller: Sends the packet and its metadata to the
+ OpenFlow controller as a ``packet in'' message.
+ * enqueue: Enqueues the packet on the specified queue
+ within port.
+ * drop: discard the packet.
+
+ Modifications include [1]:
+ * mod vlan: covered by LTD.Throughput.RFC2544.PacketLossRatioFrameModification
+ * mod_dl_src: Sets the source Ethernet address.
+ * mod_dl_dst: Sets the destination Ethernet address.
+ * mod_nw_src: Sets the IPv4 source address.
+ * mod_nw_dst: Sets the IPv4 destination address.
+ * mod_tp_src: Sets the TCP or UDP or SCTP source port.
+ * mod_tp_dst: Sets the TCP or UDP or SCTP destination port.
+ * mod_nw_tos: Sets the DSCP bits in the IPv4 ToS/DSCP or
+ IPv6 traffic class field.
+ * mod_nw_ecn: Sets the ECN bits in the appropriate IPv4 or
+ IPv6 field.
+ * mod_nw_ttl: Sets the IPv4 TTL or IPv6 hop limit field.
+
+ Note: This comprehensive list requires extensive traffic generator
+ capabilities.
+
+ The match action(s) that were applied as part of the test should be
+ reported in the final test report.
+
+ During this test, the DUT must perform the following operations on
+ the traffic flow:
+ * Perform packet parsing on the DUT’s ingress port.
+ * Perform any relevant address look-ups on the DUT’s ingress
+ ports.
+ * Carry out one or more of the match actions specified above.
+
+ The default loss percentages to be tested are: - X = 0% - X = 10^-7%
+ Other values can be tested if required by the user. The selected
+ frame sizes are those previously defined under Default Test
+ Parameters.
+
+ The test can also be used to determine the average latency of the
+ traffic when a match action is applied to packets in a flow. Under
+ the RFC2544 test methodology, the test duration will include a
+ number of trials; each trial should run for a minimum period of 60
+ seconds. A binary search methodology must be applied for each
+ trial to obtain the final result.
+
+ **Expected Result:**
+
+ At the end of each trial, the presence or absence of loss
+ determines the modification of offered load for the next trial,
+ converging on a maximum rate, or RFC2544Throughput with X% loss.
+ The Throughput load is re-used in related RFC2544 tests and other
+ tests.
+
+ **Metrics Collected:**
+
+ The following are the metrics collected for this test:
+ * The RFC 2544 Throughput in Frames Per Second (FPS) and Mbps
+ of the DUT for each frame size with X% packet loss.
+ * The average latency of the traffic flow when passing through
+ the DUT (if testing for latency, note that this average is
+ different from the test specified in Section 26.3 ofRFC2544).
+ * CPU and memory utilization may also be collected as part of
+ this test, to determine the vSwitch’s performance footprint
+ on the system.
+
+ The metrics collected can be compared to that of the prerequisite
+ test to determine the cost of the match action(s) in the pipeline.
+
+ **Deployment scenario**:
+
+ - Physical → virtual switch → physical (and others are possible)
+
+ [1] ovs-ofctl - administer OpenFlow switches
+ [http://openvswitch.org/support/dist-docs/ovs-ofctl.8.txt ]
+
.. 3.2.3.2