Revert "Moved doc files to testing document structure

This reverts commit 32a5263216d79ad34041dca55357278f092bb931.

Change-Id: I641b967badffd52ffd9e249b75e67bb7c82a8150
Signed-off-by: Trevor Cooper <trevor.cooper@intel.com>

1 files changed, 0 insertions, 1348 deletions

diff --git a/docs/testing/developer/requirements/vswitchperf_ltp.rst b/docs/testing/developer/requirements/vswitchperf_ltp.rst
deleted file mode 100644
index 2b74d676..00000000
--- a/docs/testing/developer/requirements/vswitchperf_ltp.rst
+++ /dev/null
@@ -1,1348 +0,0 @@
-.. This work is licensed under a Creative Commons Attribution 4.0 International License.
-.. http://creativecommons.org/licenses/by/4.0
-.. (c) OPNFV, Intel Corporation, AT&T and others.
-
-.. 3.1
-
-*****************************
-VSPERF LEVEL TEST PLAN (LTP)
-*****************************
-
-===============
-Introduction
-===============
-
-The objective of the OPNFV project titled
-**Characterize vSwitch Performance for Telco NFV Use Cases**, is to
-evaluate the performance of virtual switches to identify its suitability for a
-Telco Network Function Virtualization (NFV) environment. The intention of this
-Level Test Plan (LTP) document is to specify the scope, approach, resources,
-and schedule of the virtual switch performance benchmarking activities in
-OPNFV. The test cases will be identified in a separate document called the
-Level Test Design (LTD) document.
-
-This document is currently in draft form.
-
-.. 3.1.1
-
-
-.. _doc-id:
-
-Document identifier
-=========================
-
-The document id will be used to uniquely identify versions of the LTP. The
-format for the document id will be: OPNFV\_vswitchperf\_LTP\_REL\_STATUS, where
-by the status is one of: draft, reviewed, corrected or final. The document id
-for this version of the LTP is: OPNFV\_vswitchperf\_LTP\_Colorado\_REVIEWED.
-
-.. 3.1.2
-
-.. _scope:
-
-Scope
-==========
-
-The main purpose of this project is to specify a suite of
-performance tests in order to objectively measure the current packet
-transfer characteristics of a virtual switch in the NFVI. The intent of
-the project is to facilitate the performance testing of any virtual switch.
-Thus, a generic suite of tests shall be developed, with no hard dependencies to
-a single implementation. In addition, the test case suite shall be
-architecture independent.
-
-The test cases developed in this project shall not form part of a
-separate test framework, all of these tests may be inserted into the
-Continuous Integration Test Framework and/or the Platform Functionality
-Test Framework - if a vSwitch becomes a standard component of an OPNFV
-release.
-
-.. 3.1.3
-
-References
-===============
-
-*  `RFC 1242 Benchmarking Terminology for Network Interconnection
-   Devices <http://www.ietf.org/rfc/rfc1242.txt>`__
-*  `RFC 2544 Benchmarking Methodology for Network Interconnect
-   Devices <http://www.ietf.org/rfc/rfc2544.txt>`__
-*  `RFC 2285 Benchmarking Terminology for LAN Switching
-   Devices <http://www.ietf.org/rfc/rfc2285.txt>`__
-*  `RFC 2889 Benchmarking Methodology for LAN Switching
-   Devices <http://www.ietf.org/rfc/rfc2889.txt>`__
-*  `RFC 3918 Methodology for IP Multicast
-   Benchmarking <http://www.ietf.org/rfc/rfc3918.txt>`__
-*  `RFC 4737 Packet Reordering
-   Metrics <http://www.ietf.org/rfc/rfc4737.txt>`__
-*  `RFC 5481 Packet Delay Variation Applicability
-   Statement <http://www.ietf.org/rfc/rfc5481.txt>`__
-*  `RFC 6201 Device Reset
-   Characterization <http://tools.ietf.org/html/rfc6201>`__
-
-.. 3.1.4
-
-Level in the overall sequence
-===============================
-The level of testing conducted by vswitchperf in the overall testing sequence (among
-all the testing projects in OPNFV) is the performance benchmarking of a
-specific component (the vswitch) in the OPNFV platfrom. It's expected that this
-testing will follow on from the functional and integration testing conducted by
-other testing projects in OPNFV, namely Functest and Yardstick.
-
-.. 3.1.5
-
-Test classes and overall test conditions
-=========================================
-A benchmark is defined by the IETF as: A standardized test that serves as a
-basis for performance evaluation and comparison. It's important to note that
-benchmarks are not Functional tests. They do not provide PASS/FAIL criteria,
-and most importantly ARE NOT performed on live networks, or performed with live
-network traffic.
-
-In order to determine the packet transfer characteristics of a virtual switch,
-the benchmarking tests will be broken down into the following categories:
-
-- **Throughput Tests** to measure the maximum forwarding rate (in
-  frames per second or fps) and bit rate (in Mbps) for a constant load
-  (as defined by `RFC1242 <https://www.rfc-editor.org/rfc/rfc1242.txt>`__)
-  without traffic loss.
-- **Packet and Frame Delay Tests** to measure average, min and max
-  packet and frame delay for constant loads.
-- **Stream Performance Tests** (TCP, UDP) to measure bulk data transfer
-  performance, i.e. how fast systems can send and receive data through
-  the virtual switch.
-- **Request/Response Performance** Tests (TCP, UDP) the measure the
-  transaction rate through the virtual switch.
-- **Packet Delay Tests** to understand latency distribution for
-  different packet sizes and over an extended test run to uncover
-  outliers.
-- **Scalability Tests** to understand how the virtual switch performs
-  as the number of flows, active ports, complexity of the forwarding
-  logic's configuration... it has to deal with increases.
-- **Control Path and Datapath Coupling** Tests, to understand how
-  closely coupled the datapath and the control path are as well as the
-  effect of this coupling on the performance of the DUT.
-- **CPU and Memory Consumption Tests** to understand the virtual
-  switch’s footprint on the system, this includes:
-
-  * CPU core utilization.
-  * CPU cache utilization.
-  * Memory footprint.
-  * System bus (QPI, PCI, ..) utilization.
-  * Memory lanes utilization.
-  * CPU cycles consumed per packet.
-  * Time To Establish Flows Tests.
-
-- **Noisy Neighbour Tests**, to understand the effects of resource
-  sharing on the performance of a virtual switch.
-
-**Note:** some of the tests above can be conducted simultaneously where
-the combined results would be insightful, for example Packet/Frame Delay
-and Scalability.
-
-
-
-.. 3.2
-
-.. _details-of-LTP:
-
-===================================
-Details of the Level Test Plan
-===================================
-
-This section describes the following items:
-* Test items and their identifiers (TestItems_)
-* Test Traceability Matrix (TestMatrix_)
-* Features to be tested (FeaturesToBeTested_)
-* Features not to be tested (FeaturesNotToBeTested_)
-* Approach (Approach_)
-* Item pass/fail criteria (PassFailCriteria_)
-* Suspension criteria and resumption requirements (SuspensionResumptionReqs_)
-
-.. 3.2.1
-
-.. _TestItems:
-
-Test items and their identifiers
-==================================
-The test item/application vsperf is trying to test are virtual switches and in
-particular their performance in an nfv environment. vsperf will first try to
-measure the maximum achievable performance by a virtual switch and then it will
-focus in on usecases that are as close to real life deployment scenarios as
-possible.
-
-.. 3.2.2
-
-.. _TestMatrix:
-
-Test Traceability Matrix
-==========================
-vswitchperf leverages the "3x3" matrix (introduced in
-https://tools.ietf.org/html/draft-ietf-bmwg-virtual-net-02) to achieve test
-traceability. The matrix was expanded to 3x4 to accommodate scale metrics when
-displaying the coverage of many metrics/benchmarks). Test case covreage in the
-LTD is tracked using the following catagories:
-
-
-+---------------+-------------+------------+---------------+-------------+
-|               |             |            |               |             |
-|               |   SPEED     |  ACCURACY  |  RELIABILITY  |    SCALE    |
-|               |             |            |               |             |
-+---------------+-------------+------------+---------------+-------------+
-|               |             |            |               |             |
-|  Activation   |      X      |     X      |       X       |      X      |
-|               |             |            |               |             |
-+---------------+-------------+------------+---------------+-------------+
-|               |             |            |               |             |
-|  Operation    |      X      |      X     |       X       |      X      |
-|               |             |            |               |             |
-+---------------+-------------+------------+---------------+-------------+
-|               |             |            |               |             |
-| De-activation |             |            |               |             |
-|               |             |            |               |             |
-+---------------+-------------+------------+---------------+-------------+
-
-X = denotes a test catagory that has 1 or more test cases defined.
-
-.. 3.2.3
-
-.. _FeaturesToBeTested:
-
-Features to be tested
-==========================
-
-Characterizing virtual switches (i.e. Device Under Test (DUT) in this document)
-includes measuring the following performance metrics:
-
-- **Throughput** as defined by `RFC1242
-  <https://www.rfc-editor.org/rfc/rfc1242.txt>`__: The maximum rate at which
-  **none** of the offered frames are dropped by the DUT. The maximum frame
-  rate and bit rate that can be transmitted by the DUT without any error
-  should be recorded. Note there is an equivalent bit rate and a specific
-  layer at which the payloads contribute to the bits. Errors and
-  improperly formed frames or packets are dropped.
-- **Packet delay** introduced by the DUT and its cumulative effect on
-  E2E networks. Frame delay can be measured equivalently.
-- **Packet delay variation**: measured from the perspective of the
-  VNF/application. Packet delay variation is sometimes called "jitter".
-  However, we will avoid the term "jitter" as the term holds different
-  meaning to different groups of people. In this document we will
-  simply use the term packet delay variation. The preferred form for this
-  metric is the PDV form of delay variation defined in `RFC5481
-  <https://www.rfc-editor.org/rfc/rfc5481.txt>`__. The most relevant
-  measurement of PDV considers the delay variation of a single user flow,
-  as this will be relevant to the size of end-system buffers to compensate
-  for delay variation. The measurement system's ability to store the
-  delays of individual packets in the flow of interest is a key factor
-  that determines the specific measurement method. At the outset, it is
-  ideal to view the complete PDV distribution. Systems that can capture
-  and store packets and their delays have the freedom to calculate the
-  reference minimum delay and to determine various quantiles of the PDV
-  distribution accurately (in post-measurement processing routines).
-  Systems without storage must apply algorithms to calculate delay and
-  statistical measurements on the fly. For example, a system may store
-  temporary estimates of the mimimum delay and the set of (100) packets
-  with the longest delays during measurement (to calculate a high quantile,
-  and update these sets with new values periodically.
-  In some cases, a limited number of delay histogram bins will be
-  available, and the bin limits will need to be set using results from
-  repeated experiments. See section 8 of `RFC5481
-  <https://www.rfc-editor.org/rfc/rfc5481.txt>`__.
-- **Packet loss** (within a configured waiting time at the receiver): All
-  packets sent to the DUT should be accounted for.
-- **Burst behaviour**: measures the ability of the DUT to buffer packets.
-- **Packet re-ordering**: measures the ability of the device under test to
-  maintain sending order throughout transfer to the destination.
-- **Packet correctness**: packets or Frames must be well-formed, in that
-  they include all required fields, conform to length requirements, pass
-  integrity checks, etc.
-- **Availability and capacity** of the DUT i.e. when the DUT is fully “up”
-  and connected, following measurements should be captured for
-  DUT without any network packet load:
-
-  - Includes average power consumption of the CPUs (in various power states) and
-    system over specified period of time. Time period should not be less
-    than 60 seconds.
-  - Includes average per core CPU utilization over specified period of time.
-    Time period should not be less than 60 seconds.
-  - Includes the number of NIC interfaces supported.
-  - Includes headroom of VM workload processing cores (i.e. available
-    for applications).
-
-.. 3.2.4
-
-.. _FeaturesNotToBeTested:
-
-Features not to be tested
-==========================
-vsperf doesn't intend to define or perform any functional tests. The aim is to
-focus on performance.
-
-.. 3.2.5
-
-.. _Approach:
-
-Approach
-==============
-The testing approach adoped by the vswitchperf project is black box testing,
-meaning the test inputs can be generated and the outputs captured and
-completely evaluated from the outside of the System Under Test. Some metrics
-can be collected on the SUT, such as cpu or memory utilization if the
-collection has no/minimal impact on benchmark.
-This section will look at the deployment scenarios and the general methodology
-used by vswitchperf. In addition, this section will also specify the details of
-the Test Report that must be collected for each of the test cases.
-
-.. 3.2.5.1
-
-Deployment Scenarios
---------------------------
-The following represents possible deployment test scenarios which can
-help to determine the performance of both the virtual switch and the
-datapaths to physical ports (to NICs) and to logical ports (to VNFs):
-
-.. 3.2.5.1.1
-
-.. _Phy2Phy:
-
-Physical port → vSwitch → physical port
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-.. code-block:: console
-
-                                                            _
-       +--------------------------------------------------+  |
-       |              +--------------------+              |  |
-       |              |                    |              |  |
-       |              |                    v              |  |  Host
-       |   +--------------+            +--------------+   |  |
-       |   |   phy port   |  vSwitch   |   phy port   |   |  |
-       +---+--------------+------------+--------------+---+ _|
-                  ^                           :
-                  |                           |
-                  :                           v
-       +--------------------------------------------------+
-       |                                                  |
-       |                traffic generator                 |
-       |                                                  |
-       +--------------------------------------------------+
-
-.. 3.2.5.1.2
-
-.. _PVP:
-
-Physical port → vSwitch → VNF → vSwitch → physical port
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-.. code-block:: console
-
-                                                             _
-       +---------------------------------------------------+  |
-       |                                                   |  |
-       |   +-------------------------------------------+   |  |
-       |   |                 Application               |   |  |
-       |   +-------------------------------------------+   |  |
-       |       ^                                  :        |  |
-       |       |                                  |        |  |  Guest
-       |       :                                  v        |  |
-       |   +---------------+           +---------------+   |  |
-       |   | logical port 0|           | logical port 1|   |  |
-       +---+---------------+-----------+---------------+---+ _|
-               ^                                  :
-               |                                  |
-               :                                  v         _
-       +---+---------------+----------+---------------+---+  |
-       |   | logical port 0|          | logical port 1|   |  |
-       |   +---------------+          +---------------+   |  |
-       |       ^                                  :       |  |
-       |       |                                  |       |  |  Host
-       |       :                                  v       |  |
-       |   +--------------+            +--------------+   |  |
-       |   |   phy port   |  vSwitch   |   phy port   |   |  |
-       +---+--------------+------------+--------------+---+ _|
-                  ^                           :
-                  |                           |
-                  :                           v
-       +--------------------------------------------------+
-       |                                                  |
-       |                traffic generator                 |
-       |                                                  |
-       +--------------------------------------------------+
-
-.. 3.2.5.1.3
-
-.. _PVVP:
-
-Physical port → vSwitch → VNF → vSwitch → VNF → vSwitch → physical port
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-.. code-block:: console
-
-                                                       _
-    +----------------------+  +----------------------+  |
-    |   Guest 1            |  |   Guest 2            |  |
-    |   +---------------+  |  |   +---------------+  |  |
-    |   |  Application  |  |  |   |  Application  |  |  |
-    |   +---------------+  |  |   +---------------+  |  |
-    |       ^       |      |  |       ^       |      |  |
-    |       |       v      |  |       |       v      |  |  Guests
-    |   +---------------+  |  |   +---------------+  |  |
-    |   | logical ports |  |  |   | logical ports |  |  |
-    |   |   0       1   |  |  |   |   0       1   |  |  |
-    +---+---------------+--+  +---+---------------+--+ _|
-            ^       :                 ^       :
-            |       |                 |       |
-            :       v                 :       v        _
-    +---+---------------+---------+---------------+--+  |
-    |   |   0       1   |         |   3       4   |  |  |
-    |   | logical ports |         | logical ports |  |  |
-    |   +---------------+         +---------------+  |  |
-    |       ^       |                 ^       |      |  |  Host
-    |       |       L-----------------+       v      |  |
-    |   +--------------+          +--------------+   |  |
-    |   |   phy ports  | vSwitch  |   phy ports  |   |  |
-    +---+--------------+----------+--------------+---+ _|
-            ^       ^                 :       :
-            |       |                 |       |
-            :       :                 v       v
-    +--------------------------------------------------+
-    |                                                  |
-    |                traffic generator                 |
-    |                                                  |
-    +--------------------------------------------------+
-
-.. 3.2.5.1.4
-
-Physical port → VNF → vSwitch → VNF → physical port
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-.. code-block:: console
-
-                                                        _
-    +----------------------+  +----------------------+   |
-    |   Guest 1            |  |   Guest 2            |   |
-    |+-------------------+ |  | +-------------------+|   |
-    ||     Application   | |  | |     Application   ||   |
-    |+-------------------+ |  | +-------------------+|   |
-    |       ^       |      |  |       ^       |      |   |  Guests
-    |       |       v      |  |       |       v      |   |
-    |+-------------------+ |  | +-------------------+|   |
-    ||   logical ports   | |  | |   logical ports   ||   |
-    ||  0              1 | |  | | 0              1  ||   |
-    ++--------------------++  ++--------------------++  _|
-        ^              :          ^              :
-    (PCI passthrough)  |          |     (PCI passthrough)
-        |              v          :              |      _
-    +--------++------------+-+------------++---------+   |
-    |   |    ||        0   | |    1       ||     |   |   |
-    |   |    ||logical port| |logical port||     |   |   |
-    |   |    |+------------+ +------------+|     |   |   |
-    |   |    |     |                 ^     |     |   |   |
-    |   |    |     L-----------------+     |     |   |   |
-    |   |    |                             |     |   |   |  Host
-    |   |    |           vSwitch           |     |   |   |
-    |   |    +-----------------------------+     |   |   |
-    |   |                                        |   |   |
-    |   |                                        v   |   |
-    | +--------------+              +--------------+ |   |
-    | | phy port/VF  |              | phy port/VF  | |   |
-    +-+--------------+--------------+--------------+-+  _|
-        ^                                        :
-        |                                        |
-        :                                        v
-    +--------------------------------------------------+
-    |                                                  |
-    |                traffic generator                 |
-    |                                                  |
-    +--------------------------------------------------+
-
-.. 3.2.5.1.5
-
-Physical port → vSwitch → VNF
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-.. code-block:: console
-
-                                                          _
-    +---------------------------------------------------+  |
-    |                                                   |  |
-    |   +-------------------------------------------+   |  |
-    |   |                 Application               |   |  |
-    |   +-------------------------------------------+   |  |
-    |       ^                                           |  |
-    |       |                                           |  |  Guest
-    |       :                                           |  |
-    |   +---------------+                               |  |
-    |   | logical port 0|                               |  |
-    +---+---------------+-------------------------------+ _|
-            ^
-            |
-            :                                            _
-    +---+---------------+------------------------------+  |
-    |   | logical port 0|                              |  |
-    |   +---------------+                              |  |
-    |       ^                                          |  |
-    |       |                                          |  |  Host
-    |       :                                          |  |
-    |   +--------------+                               |  |
-    |   |   phy port   |  vSwitch                      |  |
-    +---+--------------+------------ -------------- ---+ _|
-               ^
-               |
-               :
-    +--------------------------------------------------+
-    |                                                  |
-    |                traffic generator                 |
-    |                                                  |
-    +--------------------------------------------------+
-
-.. 3.2.5.1.6
-
-VNF → vSwitch → physical port
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-.. code-block:: console
-
-                                                          _
-    +---------------------------------------------------+  |
-    |                                                   |  |
-    |   +-------------------------------------------+   |  |
-    |   |                 Application               |   |  |
-    |   +-------------------------------------------+   |  |
-    |                                          :        |  |
-    |                                          |        |  |  Guest
-    |                                          v        |  |
-    |                               +---------------+   |  |
-    |                               | logical port  |   |  |
-    +-------------------------------+---------------+---+ _|
-                                               :
-                                               |
-                                               v         _
-    +------------------------------+---------------+---+  |
-    |                              | logical port  |   |  |
-    |                              +---------------+   |  |
-    |                                          :       |  |
-    |                                          |       |  |  Host
-    |                                          v       |  |
-    |                               +--------------+   |  |
-    |                     vSwitch   |   phy port   |   |  |
-    +-------------------------------+--------------+---+ _|
-                                           :
-                                           |
-                                           v
-    +--------------------------------------------------+
-    |                                                  |
-    |                traffic generator                 |
-    |                                                  |
-    +--------------------------------------------------+
-
-.. 3.2.5.1.7
-
-VNF → vSwitch → VNF → vSwitch
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-.. code-block:: console
-
-                                                             _
-    +-------------------------+  +-------------------------+  |
-    |   Guest 1               |  |   Guest 2               |  |
-    |   +-----------------+   |  |   +-----------------+   |  |
-    |   |   Application   |   |  |   |   Application   |   |  |
-    |   +-----------------+   |  |   +-----------------+   |  |
-    |                :        |  |       ^                 |  |
-    |                |        |  |       |                 |  |  Guest
-    |                v        |  |       :                 |  |
-    |     +---------------+   |  |   +---------------+     |  |
-    |     | logical port 0|   |  |   | logical port 0|     |  |
-    +-----+---------------+---+  +---+---------------+-----+ _|
-                    :                    ^
-                    |                    |
-                    v                    :                    _
-    +----+---------------+------------+---------------+-----+  |
-    |    |     port 0    |            |     port 1    |     |  |
-    |    +---------------+            +---------------+     |  |
-    |              :                    ^                   |  |
-    |              |                    |                   |  |  Host
-    |              +--------------------+                   |  |
-    |                                                       |  |
-    |                     vswitch                           |  |
-    +-------------------------------------------------------+ _|
-
-.. 3.2.5.1.8
-
-HOST 1(Physical port → virtual switch → VNF → virtual switch → Physical port)
-→ HOST 2(Physical port → virtual switch → VNF → virtual switch → Physical port)
-
-HOST 1 (PVP) → HOST 2 (PVP)
-~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-.. code-block:: console
-
-                                                       _
-    +----------------------+  +----------------------+  |
-    |   Guest 1            |  |   Guest 2            |  |
-    |   +---------------+  |  |   +---------------+  |  |
-    |   |  Application  |  |  |   |  Application  |  |  |
-    |   +---------------+  |  |   +---------------+  |  |
-    |       ^       |      |  |       ^       |      |  |
-    |       |       v      |  |       |       v      |  |  Guests
-    |   +---------------+  |  |   +---------------+  |  |
-    |   | logical ports |  |  |   | logical ports |  |  |
-    |   |   0       1   |  |  |   |   0       1   |  |  |
-    +---+---------------+--+  +---+---------------+--+ _|
-            ^       :                 ^       :
-            |       |                 |       |
-            :       v                 :       v        _
-    +---+---------------+--+  +---+---------------+--+  |
-    |   |   0       1   |  |  |   |   3       4   |  |  |
-    |   | logical ports |  |  |   | logical ports |  |  |
-    |   +---------------+  |  |   +---------------+  |  |
-    |       ^       |      |  |       ^       |      |  |  Hosts
-    |       |       v      |  |       |       v      |  |
-    |   +--------------+   |  |   +--------------+   |  |
-    |   |   phy ports  |   |  |   |   phy ports  |   |  |
-    +---+--------------+---+  +---+--------------+---+ _|
-            ^       :                 :       :
-            |       +-----------------+       |
-            :                                 v
-    +--------------------------------------------------+
-    |                                                  |
-    |                traffic generator                 |
-    |                                                  |
-    +--------------------------------------------------+
-
-
-
-**Note:** For tests where the traffic generator and/or measurement
-receiver are implemented on VM and connected to the virtual switch
-through vNIC, the issues of shared resources and interactions between
-the measurement devices and the device under test must be considered.
-
-**Note:** Some RFC 2889 tests require a full-mesh sending and receiving
-pattern involving more than two ports. This possibility is illustrated in the
-Physical port → vSwitch → VNF → vSwitch → VNF → vSwitch → physical port
-diagram above (with 2 sending and 2 receiving ports, though all ports
-could be used bi-directionally).
-
-**Note:** When Deployment Scenarios are used in RFC 2889 address learning
-or cache capacity testing, an additional port from the vSwitch must be
-connected to the test device. This port is used to listen for flooded
-frames.
-
-.. 3.2.5.2
-
-General Methodology:
---------------------------
-To establish the baseline performance of the virtual switch, tests would
-initially be run with a simple workload in the VNF (the recommended
-simple workload VNF would be `DPDK <http://www.dpdk.org/>`__'s testpmd
-application forwarding packets in a VM or vloop\_vnf a simple kernel
-module that forwards traffic between two network interfaces inside the
-virtualized environment while bypassing the networking stack).
-Subsequently, the tests would also be executed with a real Telco
-workload running in the VNF, which would exercise the virtual switch in
-the context of higher level Telco NFV use cases, and prove that its
-underlying characteristics and behaviour can be measured and validated.
-Suitable real Telco workload VNFs are yet to be identified.
-
-.. 3.2.5.2.1
-
-.. _default-test-parameters:
-
-Default Test Parameters
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-The following list identifies the default parameters for suite of
-tests:
-
--  Reference application: Simple forwarding or Open Source VNF.
--  Frame size (bytes): 64, 128, 256, 512, 1024, 1280, 1518, 2K, 4k OR
-   Packet size based on use-case (e.g. RTP 64B, 256B) OR Mix of packet sizes as
-   maintained by the Functest project <https://wiki.opnfv.org/traffic_profile_management>.
--  Reordering check: Tests should confirm that packets within a flow are
-   not reordered.
--  Duplex: Unidirectional / Bidirectional. Default: Full duplex with
-   traffic transmitting in both directions, as network traffic generally
-   does not flow in a single direction. By default the data rate of
-   transmitted traffic should be the same in both directions, please
-   note that asymmetric traffic (e.g. downlink-heavy) tests will be
-   mentioned explicitly for the relevant test cases.
--  Number of Flows: Default for non scalability tests is a single flow.
-   For scalability tests the goal is to test with maximum supported
-   flows but where possible will test up to 10 Million flows. Start with
-   a single flow and scale up. By default flows should be added
-   sequentially, tests that add flows simultaneously will explicitly
-   call out their flow addition behaviour. Packets are generated across
-   the flows uniformly with no burstiness. For multi-core tests should
-   consider the number of packet flows based on vSwitch/VNF multi-thread
-   implementation and behavior.
-
--  Traffic Types: UDP, SCTP, RTP, GTP and UDP traffic.
--  Deployment scenarios are:
--  Physical → virtual switch → physical.
--  Physical → virtual switch → VNF → virtual switch → physical.
--  Physical → virtual switch → VNF → virtual switch → VNF → virtual
-   switch → physical.
--  Physical → VNF → virtual switch → VNF → physical.
--  Physical → virtual switch → VNF.
--  VNF → virtual switch → Physical.
--  VNF → virtual switch → VNF.
-
-Tests MUST have these parameters unless otherwise stated. **Test cases
-with non default parameters will be stated explicitly**.
-
-**Note**: For throughput tests unless stated otherwise, test
-configurations should ensure that traffic traverses the installed flows
-through the virtual switch, i.e. flows are installed and have an appropriate
-time out that doesn't expire before packet transmission starts.
-
-.. 3.2.5.2.2
-
-Flow Classification
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-Virtual switches classify packets into flows by processing and matching
-particular header fields in the packet/frame and/or the input port where
-the packets/frames arrived. The vSwitch then carries out an action on
-the group of packets that match the classification parameters. Thus a
-flow is considered to be a sequence of packets that have a shared set of
-header field values or have arrived on the same port and have the same
-action applied to them. Performance results can vary based on the
-parameters the vSwitch uses to match for a flow. The recommended flow
-classification parameters for L3 vSwitch performance tests are: the
-input port, the source IP address, the destination IP address and the
-Ethernet protocol type field. It is essential to increase the flow
-time-out time on a vSwitch before conducting any performance tests that
-do not measure the flow set-up time. Normally the first packet of a
-particular flow will install the flow in the vSwitch which adds an
-additional latency, subsequent packets of the same flow are not subject
-to this latency if the flow is already installed on the vSwitch.
-
-.. 3.2.5.2.3
-
-Test Priority
-~~~~~~~~~~~~~~~~~~~~~
-
-Tests will be assigned a priority in order to determine which tests
-should be implemented immediately and which tests implementations
-can be deferred.
-
-Priority can be of following types: - Urgent: Must be implemented
-immediately. - High: Must be implemented in the next release. - Medium:
-May be implemented after the release. - Low: May or may not be
-implemented at all.
-
-.. 3.2.5.2.4
-
-SUT Setup
-~~~~~~~~~~~~~~~~~~
-
-The SUT should be configured to its "default" state. The
-SUT's configuration or set-up must not change between tests in any way
-other than what is required to do the test. All supported protocols must
-be configured and enabled for each test set up.
-
-.. 3.2.5.2.5
-
-Port Configuration
-~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-The DUT should be configured with n ports where
-n is a multiple of 2. Half of the ports on the DUT should be used as
-ingress ports and the other half of the ports on the DUT should be used
-as egress ports. Where a DUT has more than 2 ports, the ingress data
-streams should be set-up so that they transmit packets to the egress
-ports in sequence so that there is an even distribution of traffic
-across ports. For example, if a DUT has 4 ports 0(ingress), 1(ingress),
-2(egress) and 3(egress), the traffic stream directed at port 0 should
-output a packet to port 2 followed by a packet to port 3. The traffic
-stream directed at port 1 should also output a packet to port 2 followed
-by a packet to port 3.
-
-.. 3.2.5.2.6
-
-Frame Formats
-~~~~~~~~~~~~~~~~~~~~~
-
-**Frame formats Layer 2 (data link layer) protocols**
-
--  Ethernet II
-
-.. code-block:: console
-
-     +---------------------------+-----------+
-     | Ethernet Header | Payload | Check Sum |
-     +-----------------+---------+-----------+
-     |_________________|_________|___________|
-           14 Bytes     46 - 1500   4 Bytes
-                          Bytes
-
-
-**Layer 3 (network layer) protocols**
-
--  IPv4
-
-.. code-block:: console
-
-     +-----------------+-----------+---------+-----------+
-     | Ethernet Header | IP Header | Payload | Checksum  |
-     +-----------------+-----------+---------+-----------+
-     |_________________|___________|_________|___________|
-           14 Bytes       20 bytes  26 - 1480   4 Bytes
-                                      Bytes
-
--  IPv6
-
-.. code-block:: console
-
-     +-----------------+-----------+---------+-----------+
-     | Ethernet Header | IP Header | Payload | Checksum  |
-     +-----------------+-----------+---------+-----------+
-     |_________________|___________|_________|___________|
-           14 Bytes       40 bytes  26 - 1460   4 Bytes
-                                      Bytes
-
-**Layer 4 (transport layer) protocols**
-
-  - TCP
-  - UDP
-  - SCTP
-
-.. code-block:: console
-
-     +-----------------+-----------+-----------------+---------+-----------+
-     | Ethernet Header | IP Header | Layer 4 Header  | Payload | Checksum  |
-     +-----------------+-----------+-----------------+---------+-----------+
-     |_________________|___________|_________________|_________|___________|
-           14 Bytes      40 bytes      20 Bytes       6 - 1460   4 Bytes
-                                                       Bytes
-
-
-**Layer 5 (application layer) protocols**
-
-  - RTP
-  - GTP
-
-.. code-block:: console
-
-     +-----------------+-----------+-----------------+---------+-----------+
-     | Ethernet Header | IP Header | Layer 4 Header  | Payload | Checksum  |
-     +-----------------+-----------+-----------------+---------+-----------+
-     |_________________|___________|_________________|_________|___________|
-           14 Bytes      20 bytes     20 Bytes        >= 6 Bytes   4 Bytes
-
-.. 3.2.5.2.7
-
-Packet Throughput
-~~~~~~~~~~~~~~~~~~~~~~~~~
-There is a difference between an Ethernet frame,
-an IP packet, and a UDP datagram. In the seven-layer OSI model of
-computer networking, packet refers to a data unit at layer 3 (network
-layer). The correct term for a data unit at layer 2 (data link layer) is
-a frame, and at layer 4 (transport layer) is a segment or datagram.
-
-Important concepts related to 10GbE performance are frame rate and
-throughput. The MAC bit rate of 10GbE, defined in the IEEE standard 802
-.3ae, is 10 billion bits per second. Frame rate is based on the bit rate
-and frame format definitions. Throughput, defined in IETF RFC 1242, is
-the highest rate at which the system under test can forward the offered
-load, without loss.
-
-The frame rate for 10GbE is determined by a formula that divides the 10
-billion bits per second by the preamble + frame length + inter-frame
-gap.
-
-The maximum frame rate is calculated using the minimum values of the
-following parameters, as described in the IEEE 802 .3ae standard:
-
--  Preamble: 8 bytes \* 8 = 64 bits
--  Frame Length: 64 bytes (minimum) \* 8 = 512 bits
--  Inter-frame Gap: 12 bytes (minimum) \* 8 = 96 bits
-
-Therefore, Maximum Frame Rate (64B Frames)
-= MAC Transmit Bit Rate / (Preamble + Frame Length + Inter-frame Gap)
-= 10,000,000,000 / (64 + 512 + 96)
-= 10,000,000,000 / 672
-= 14,880,952.38 frame per second (fps)
-
-.. 3.2.5.3
-
-RFCs for testing virtual switch performance
---------------------------------------------------
-
-The starting point for defining the suite of tests for benchmarking the
-performance of a virtual switch is to take existing RFCs and standards
-that were designed to test their physical counterparts and adapting them
-for testing virtual switches. The rationale behind this is to establish
-a fair comparison between the performance of virtual and physical
-switches. This section outlines the RFCs that are used by this
-specification.
-
-.. 3.2.5.3.1
-
-RFC 1242 Benchmarking Terminology for Network Interconnection
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-Devices RFC 1242 defines the terminology that is used in describing
-performance benchmarking tests and their results. Definitions and
-discussions covered include: Back-to-back, bridge, bridge/router,
-constant load, data link frame size, frame loss rate, inter frame gap,
-latency, and many more.
-
-.. 3.2.5.3.2
-
-RFC 2544 Benchmarking Methodology for Network Interconnect Devices
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-RFC 2544 outlines a benchmarking methodology for network Interconnect
-Devices. The methodology results in performance metrics such as latency,
-frame loss percentage, and maximum data throughput.
-
-In this document network “throughput” (measured in millions of frames
-per second) is based on RFC 2544, unless otherwise noted. Frame size
-refers to Ethernet frames ranging from smallest frames of 64 bytes to
-largest frames of 9K bytes.
-
-Types of tests are:
-
-1. Throughput test defines the maximum number of frames per second
-   that can be transmitted without any error, or 0% loss ratio.
-   In some Throughput tests (and those tests with long duration),
-   evaluation of an additional frame loss ratio is suggested. The
-   current ratio (10^-7 %) is based on understanding the typical
-   user-to-user packet loss ratio needed for good application
-   performance and recognizing that a single transfer through a
-   vswitch must contribute a tiny fraction of user-to-user loss.
-   Further, the ratio 10^-7 % also recognizes practical limitations
-   when measuring loss ratio.
-
-2. Latency test measures the time required for a frame to travel from
-   the originating device through the network to the destination device.
-   Please note that RFC2544 Latency measurement will be superseded with
-   a measurement of average latency over all successfully transferred
-   packets or frames.
-
-3. Frame loss test measures the network’s
-   response in overload conditions - a critical indicator of the
-   network’s ability to support real-time applications in which a
-   large amount of frame loss will rapidly degrade service quality.
-
-4. Burst test assesses the buffering capability of a virtual switch. It
-   measures the maximum number of frames received at full line rate
-   before a frame is lost. In carrier Ethernet networks, this
-   measurement validates the excess information rate (EIR) as defined in
-   many SLAs.
-
-5. System recovery to characterize speed of recovery from an overload
-   condition.
-
-6. Reset to characterize speed of recovery from device or software
-   reset. This type of test has been updated by `RFC6201
-   <https://www.rfc-editor.org/rfc/rfc6201.txt>`__ as such,
-   the methodology defined by this specification will be that of RFC 6201.
-
-Although not included in the defined RFC 2544 standard, another crucial
-measurement in Ethernet networking is packet delay variation. The
-definition set out by this specification comes from
-`RFC5481 <https://www.rfc-editor.org/rfc/rfc5481.txt>`__.
-
-.. 3.2.5.3.3
-
-RFC 2285 Benchmarking Terminology for LAN Switching Devices
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-RFC 2285 defines the terminology that is used to describe the
-terminology for benchmarking a LAN switching device. It extends RFC
-1242 and defines: DUTs, SUTs, Traffic orientation and distribution,
-bursts, loads, forwarding rates, etc.
-
-.. 3.2.5.3.4
-
-RFC 2889 Benchmarking Methodology for LAN Switching
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-RFC 2889 outlines a benchmarking methodology for LAN switching, it
-extends RFC 2544. The outlined methodology gathers performance
-metrics for forwarding, congestion control, latency, address handling
-and finally filtering.
-
-.. 3.2.5.3.5
-
-RFC 3918 Methodology for IP Multicast Benchmarking
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-RFC 3918 outlines a methodology for IP Multicast benchmarking.
-
-.. 3.2.5.3.6
-
-RFC 4737 Packet Reordering Metrics
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-RFC 4737 describes metrics for identifying and counting re-ordered
-packets within a stream, and metrics to measure the extent each
-packet has been re-ordered.
-
-.. 3.2.5.3.7
-
-RFC 5481 Packet Delay Variation Applicability Statement
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-RFC 5481 defined two common, but different forms of delay variation
-metrics, and compares the metrics over a range of networking
-circumstances and tasks. The most suitable form for vSwitch
-benchmarking is the "PDV" form.
-
-.. 3.2.5.3.8
-
-RFC 6201 Device Reset Characterization
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-RFC 6201 extends the methodology for characterizing the speed of
-recovery of the DUT from device or software reset described in RFC
-2544.
-
-.. 3.2.6:
-
-.. _PassFailCriteria:
-
-Item pass/fail criteria
-=========================
-
-vswitchperf does not specify Pass/Fail criteria for the tests in terms of a
-threshold, as benchmarks do not (and should not do this). The results/metrics
-for a test are simply reported. If it had to be defined, a test is considered
-to have passed if it succesfully completed and a relavent metric was
-recorded/reported for the SUT.
-
-.. 3.2.7:
-
-.. _SuspensionResumptionReqs:
-
-Suspension criteria and resumption requirements
-================================================
-In the case of a throughput test, a test should be suspended if a virtual
-switch is failing to forward any traffic. A test should be restarted from a
-clean state if the intention is to carry out the test again.
-
-.. 3.2.8:
-
-.. _TestDelierables:
-
-Test deliverables
-==================
-Each test should produce a test report that details SUT information as well as
-the test results. There are a number of parameters related to the system, DUT
-and tests that can affect the repeatability of a test results and should be
-recorded. In order to minimise the variation in the results of a test,
-it is recommended that the test report includes the following information:
-
--  Hardware details including:
-
-   -  Platform details.
-   -  Processor details.
-   -  Memory information (see below)
-   -  Number of enabled cores.
-   -  Number of cores used for the test.
-   -  Number of physical NICs, as well as their details (manufacturer,
-      versions, type and the PCI slot they are plugged into).
-   -  NIC interrupt configuration.
-   -  BIOS version, release date and any configurations that were
-      modified.
-
--  Software details including:
-
-   -  OS version (for host and VNF)
-   -  Kernel version (for host and VNF)
-   -  GRUB boot parameters (for host and VNF).
-   -  Hypervisor details (Type and version).
-   -  Selected vSwitch, version number or commit id used.
-   -  vSwitch launch command line if it has been parameterised.
-   -  Memory allocation to the vSwitch – which NUMA node it is using,
-      and how many memory channels.
-   -  Where the vswitch is built from source: compiler details including
-      versions and the flags that were used to compile the vSwitch.
-   -  DPDK or any other SW dependency version number or commit id used.
-   -  Memory allocation to a VM - if it's from Hugpages/elsewhere.
-   -  VM storage type: snapshot/independent persistent/independent
-      non-persistent.
-   -  Number of VMs.
-   -  Number of Virtual NICs (vNICs), versions, type and driver.
-   -  Number of virtual CPUs and their core affinity on the host.
-   -  Number vNIC interrupt configuration.
-   -  Thread affinitization for the applications (including the vSwitch
-      itself) on the host.
-   -  Details of Resource isolation, such as CPUs designated for
-      Host/Kernel (isolcpu) and CPUs designated for specific processes
-      (taskset).
-
--  Memory Details
-
-   -  Total memory
-   -  Type of memory
-   -  Used memory
-   -  Active memory
-   -  Inactive memory
-   -  Free memory
-   -  Buffer memory
-   -  Swap cache
-   -  Total swap
-   -  Used swap
-   -  Free swap
-
--  Test duration.
--  Number of flows.
--  Traffic Information:
-
-   -  Traffic type - UDP, TCP, IMIX / Other.
-   -  Packet Sizes.
-
--  Deployment Scenario.
-
-**Note**: Tests that require additional parameters to be recorded will
-explicitly specify this.
-
-
-.. 3.3:
-
-.. _TestManagement:
-
-Test management
-=================
-This section will detail the test activities that will be conducted by vsperf
-as well as the infrastructure that will be used to complete the tests in OPNFV.
-
-.. 3.3.1:
-
-Planned activities and tasks; test progression
-=================================================
-A key consideration when conducting any sort of benchmark is trying to
-ensure the consistency and repeatability of test results between runs.
-When benchmarking the performance of a virtual switch there are many
-factors that can affect the consistency of results. This section
-describes these factors and the measures that can be taken to limit
-their effects. In addition, this section will outline some system tests
-to validate the platform and the VNF before conducting any vSwitch
-benchmarking tests.
-
-**System Isolation:**
-
-When conducting a benchmarking test on any SUT, it is essential to limit
-(and if reasonable, eliminate) any noise that may interfere with the
-accuracy of the metrics collected by the test. This noise may be
-introduced by other hardware or software (OS, other applications), and
-can result in significantly varying performance metrics being collected
-between consecutive runs of the same test. In the case of characterizing
-the performance of a virtual switch, there are a number of configuration
-parameters that can help increase the repeatability and stability of
-test results, including:
-
--  OS/GRUB configuration:
-
-   -  maxcpus = n where n >= 0; limits the kernel to using 'n'
-      processors. Only use exactly what you need.
-   -  isolcpus: Isolate CPUs from the general scheduler. Isolate all
-      CPUs bar one which will be used by the OS.
-   -  use taskset to affinitize the forwarding application and the VNFs
-      onto isolated cores. VNFs and the vSwitch should be allocated
-      their own cores, i.e. must not share the same cores. vCPUs for the
-      VNF should be affinitized to individual cores also.
-   -  Limit the amount of background applications that are running and
-      set OS to boot to runlevel 3. Make sure to kill any unnecessary
-      system processes/daemons.
-   -  Only enable hardware that you need to use for your test – to
-      ensure there are no other interrupts on the system.
-   -  Configure NIC interrupts to only use the cores that are not
-      allocated to any other process (VNF/vSwitch).
-
--  NUMA configuration: Any unused sockets in a multi-socket system
-   should be disabled.
--  CPU pinning: The vSwitch and the VNF should each be affinitized to
-   separate logical cores using a combination of maxcpus, isolcpus and
-   taskset.
--  BIOS configuration: BIOS should be configured for performance where
-   an explicit option exists, sleep states should be disabled, any
-   virtualization optimization technologies should be enabled, and
-   hyperthreading should also be enabled, turbo boost and overclocking
-   should be disabled.
-
-**System Validation:**
-
-System validation is broken down into two sub-categories: Platform
-validation and VNF validation. The validation test itself involves
-verifying the forwarding capability and stability for the sub-system
-under test. The rationale behind system validation is two fold. Firstly
-to give a tester confidence in the stability of the platform or VNF that
-is being tested; and secondly to provide base performance comparison
-points to understand the overhead introduced by the virtual switch.
-
-* Benchmark platform forwarding capability: This is an OPTIONAL test
-  used to verify the platform and measure the base performance (maximum
-  forwarding rate in fps and latency) that can be achieved by the
-  platform without a vSwitch or a VNF. The following diagram outlines
-  the set-up for benchmarking Platform forwarding capability:
-
-  .. code-block:: console
-
-                                                            __
-       +--------------------------------------------------+   |
-       |   +------------------------------------------+   |   |
-       |   |                                          |   |   |
-       |   |          l2fw or DPDK L2FWD app          |   |  Host
-       |   |                                          |   |   |
-       |   +------------------------------------------+   |   |
-       |   |                 NIC                      |   |   |
-       +---+------------------------------------------+---+ __|
-                  ^                           :
-                  |                           |
-                  :                           v
-       +--------------------------------------------------+
-       |                                                  |
-       |                traffic generator                 |
-       |                                                  |
-       +--------------------------------------------------+
-
-* Benchmark VNF forwarding capability: This test is used to verify
-  the VNF and measure the base performance (maximum forwarding rate in
-  fps and latency) that can be achieved by the VNF without a vSwitch.
-  The performance metrics collected by this test will serve as a key
-  comparison point for NIC passthrough technologies and vSwitches. VNF
-  in this context refers to the hypervisor and the VM. The following
-  diagram outlines the set-up for benchmarking VNF forwarding
-  capability:
-
-  .. code-block:: console
-
-                                                            __
-       +--------------------------------------------------+   |
-       |   +------------------------------------------+   |   |
-       |   |                                          |   |   |
-       |   |                 VNF                      |   |   |
-       |   |                                          |   |   |
-       |   +------------------------------------------+   |   |
-       |   |          Passthrough/SR-IOV              |   |  Host
-       |   +------------------------------------------+   |   |
-       |   |                 NIC                      |   |   |
-       +---+------------------------------------------+---+ __|
-                  ^                           :
-                  |                           |
-                  :                           v
-       +--------------------------------------------------+
-       |                                                  |
-       |                traffic generator                 |
-       |                                                  |
-       +--------------------------------------------------+
-
-
-**Methodology to benchmark Platform/VNF forwarding capability**
-
-
-The recommended methodology for the platform/VNF validation and
-benchmark is: - Run `RFC2889 <https://www.rfc-editor.org/rfc/rfc2289.txt>`__
-Maximum Forwarding Rate test, this test will produce maximum
-forwarding rate and latency results that will serve as the
-expected values. These expected values can be used in
-subsequent steps or compared with in subsequent validation tests. -
-Transmit bidirectional traffic at line rate/max forwarding rate
-(whichever is higher) for at least 72 hours, measure throughput (fps)
-and latency. - Note: Traffic should be bidirectional. - Establish a
-baseline forwarding rate for what the platform can achieve. - Additional
-validation: After the test has completed for 72 hours run bidirectional
-traffic at the maximum forwarding rate once more to see if the system is
-still functional and measure throughput (fps) and latency. Compare the
-measure the new obtained values with the expected values.
-
-**NOTE 1**: How the Platform is configured for its forwarding capability
-test (BIOS settings, GRUB configuration, runlevel...) is how the
-platform should be configured for every test after this
-
-**NOTE 2**: How the VNF is configured for its forwarding capability test
-(# of vCPUs, vNICs, Memory, affinitization…) is how it should be
-configured for every test that uses a VNF after this.
-
-**Methodology to benchmark the VNF to vSwitch to VNF deployment scenario**
-
-vsperf has identified the following concerns when benchmarking the VNF to
-vSwitch to VNF deployment scenario:
-
-* The accuracy of the timing synchronization between VNFs/VMs.
-* The clock accuracy of a VNF/VM if they were to be used as traffic generators.
-* VNF traffic generator/receiver may be using resources of the system under
-  test, causing at least three forms of workload to increase as the traffic
-  load increases (generation, switching, receiving).
-
-The recommendation from vsperf is that tests for this sceanario must
-include an external HW traffic generator to act as the tester/traffic transmitter
-and receiver. The perscribed methodology to benchmark this deployment scanrio with
-an external tester involves the following three steps:
-
-#. Determine the forwarding capability and latency through the virtual interface
-connected to the VNF/VM.
-
-.. Figure:: vm2vm_virtual_interface_benchmark.png
-
-   Virtual interfaces performance benchmark
-
-#. Determine the forwarding capability and latency through the VNF/hypervisor.
-
-.. Figure:: vm2vm_hypervisor_benchmark.png
-
-   Hypervisor performance benchmark
-
-#. Determine the forwarding capability and latency for the VNF to vSwitch to VNF
-   taking the information from the previous two steps into account.
-
-.. Figure:: vm2vm_benchmark.png
-
-   VNF to vSwitch to VNF performance benchmark
-
-vsperf also identified an alternative configuration for the final step:
-
-.. Figure:: vm2vm_alternative_benchmark.png
-
-   VNF to vSwitch to VNF alternative performance benchmark
-
-.. 3.3.2:
-
-Environment/infrastructure
-============================
-Intel is providing a hosted test-bed with nine bare-metal environments
-allocated to different OPNFV projects. Currently a number of servers in
-`Intel POD 3 <https://wiki.opnfv.org/display/pharos/Intel+Pod3>`__ are
-allocated to vsperf:
-
-  * pod3-wcp-node3 and pod3-wcp-node4 which are used for CI jobs.
-  * pod3-node6 which is used as a vsperf sandbox environment.
-
-vsperf CI
----------
-vsperf CI jobs are broken down into:
-
-  * Daily job:
-
-    * Runs everyday takes about 10 hours to complete.
-    * TESTCASES_DAILY='phy2phy_tput back2back phy2phy_tput_mod_vlan
-      phy2phy_scalability pvp_tput pvp_back2back pvvp_tput pvvp_back2back'.
-    * TESTPARAM_DAILY='--test-params TRAFFICGEN_PKT_SIZES=(64,128,512,1024,1518)'.
-
-  * Merge job:
-
-    * Runs whenever patches are merged to master.
-    * Runs a basic Sanity test.
-
-  * Verify job:
-
-    * Runs every time a patch is pushed to gerrit.
-    * Builds documentation.
-
-Scripts:
---------
-There are 2 scripts that are part of VSPERFs CI:
-
-  * build-vsperf.sh: Lives in the VSPERF repository in the ci/ directory and is
-    used to run vsperf with the appropriate cli parameters.
-  * vswitchperf.yml: YAML description of our jenkins job. lives in the RELENG
-    repository.
-
-More info on vsperf CI can be found here:
-https://wiki.opnfv.org/display/vsperf/VSPERF+CI
-
-.. 3.3.3:
-
-Responsibilities and authority
-===============================
-The group responsible for managing, designing, preparing and executing the
-tests listed in the LTD are the vsperf committers and contributors. The vsperf
-committers and contributors should work with the relavent OPNFV projects to
-ensure that the infrastructure is in place for testing vswitches, and that the
-results are published to common end point (a results database).
-