aboutsummaryrefslogtreecommitdiffstats
path: root/docs
diff options
context:
space:
mode:
Diffstat (limited to 'docs')
-rw-r--r--docs/requirements/vswitchperf_ltd.rst91
1 files changed, 91 insertions, 0 deletions
diff --git a/docs/requirements/vswitchperf_ltd.rst b/docs/requirements/vswitchperf_ltd.rst
index 4a08bdd6..77396121 100644
--- a/docs/requirements/vswitchperf_ltd.rst
+++ b/docs/requirements/vswitchperf_ltd.rst
@@ -1759,6 +1759,97 @@ Test ID: LTD.Throughput.RFC2889.BroadcastFrameForwarding
four test ports are required. One of the ports is connected to the test
device, so it can send broadcast frames and listen for miss-routed frames.
+.. 3.2.3.1.13
+
+Test ID: LTD.Throughput.RFC2544.WorstN-BestN
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ **Title**: Modified RFC 2544 X% packet loss ratio Throughput and Latency Test
+
+ **Prerequisite Test**: N/A
+
+ **Priority**:
+
+ **Description**:
+
+ This test determines the DUT's maximum forwarding rate with X% traffic
+ loss for a constant load (fixed length frames at a fixed interval time).
+ The default loss percentages to be tested are: X = 0%, X = 10^-7%
+
+ Modified RFC 2544 throughput benchmarking methodology aims to quantify
+ the throughput measurement variations observed during standard RFC 2544
+ benchmarking measurements of virtual switches and VNFs. The RFC2544
+ binary search algorithm is modified to use more samples per test trial
+ to drive the binary search and yield statistically more meaningful
+ results. This keeps the heart of the RFC2544 methodology, still relying
+ on the binary search of throughput at specified loss tolerance, while
+ providing more useful information about the range of results seen in
+ testing. Instead of using a single traffic trial per iteration step,
+ each traffic trial is repeated N times and the success/failure of the
+ iteration step is based on these N traffic trials. Two types of revised
+ tests are defined - *Worst-of-N* and *Best-of-N*.
+
+ **Worst-of-N**
+
+ *Worst-of-N* indicates the lowest expected maximum throughput for (
+ packet size, loss tolerance) when repeating the test.
+
+ 1. Repeat the same test run N times at a set packet rate, record each
+ result.
+ 2. Take the WORST result (highest packet loss) out of N result samples,
+ called the Worst-of-N sample.
+ 3. If Worst-of-N sample has loss less than the set loss tolerance, then
+ the step is successful - increase the test traffic rate.
+ 4. If Worst-of-N sample has loss greater than the set loss tolerance
+ then the step failed - decrease the test traffic rate.
+ 5. Go to step 1.
+
+ **Best-of-N**
+
+ *Best-of-N* indicates the highest expected maximum throughput for (
+ packet size, loss tolerance) when repeating the test.
+
+ 1. Repeat the same traffic run N times at a set packet rate, record
+ each result.
+ 2. Take the BEST result (least packet loss) out of N result samples,
+ called the Best-of-N sample.
+ 3. If Best-of-N sample has loss less than the set loss tolerance, then
+ the step is successful - increase the test traffic rate.
+ 4. If Best-of-N sample has loss greater than the set loss tolerance,
+ then the step failed - decrease the test traffic rate.
+ 5. Go to step 1.
+
+ Performing both Worst-of-N and Best-of-N benchmark tests yields lower
+ and upper bounds of expected maximum throughput under the operating
+ conditions, giving a very good indication to the user of the
+ deterministic performance range for the tested setup.
+
+ **Expected Result**: At the end of each trial series, the presence or
+ absence of loss determines the modification of offered load for the
+ next trial series, converging on a maximum rate, or
+ `RFC2544 <https://www.rfc-editor.org/rfc/rfc2544.txt>`__ Throughput
+ with X% loss.
+ The Throughput load is re-used in related
+ `RFC2544 <https://www.rfc-editor.org/rfc/rfc2544.txt>`__ tests and other
+ tests.
+
+ **Metrics Collected**:
+
+ The following are the metrics collected for this test:
+
+ - The maximum forwarding rate in Frames Per Second (FPS) and Mbps of
+ the DUT for each frame size with X% packet loss.
+ - The average latency of the traffic flow when passing through the DUT
+ (if testing for latency, note that this average is different from the
+ test specified in Section 26.3 of
+ `RFC2544 <https://www.rfc-editor.org/rfc/rfc2544.txt>`__).
+ - Following may also be collected as part of this test, to determine
+ the vSwitch's performance footprint on the system:
+ - CPU core utilization.
+ - CPU cache utilization.
+ - Memory footprint.
+ - System bus (QPI, PCI, ...) utilization.
+ - CPU cycles consumed per packet.
+
.. 3.2.3.2
Packet Latency tests