diff options
Diffstat (limited to 'conf/03_traffic.conf')
-rw-r--r-- | conf/03_traffic.conf | 60 |
1 files changed, 55 insertions, 5 deletions
diff --git a/conf/03_traffic.conf b/conf/03_traffic.conf index 67318893..597f2ceb 100644 --- a/conf/03_traffic.conf +++ b/conf/03_traffic.conf @@ -1,4 +1,4 @@ -# Copyright 2015-2017 Intel Corporation. +# Copyright 2015-2018 Intel Corporation., Tieto # # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. @@ -23,8 +23,8 @@ LOG_FILE_TRAFFIC_GEN = 'traffic-gen.log' # Detailed description of TRAFFIC dictionary items follows: # # 'traffic_type' - One of the supported traffic types. -# E.g. rfc2544_throughput, rfc2544_back2back -# or rfc2544_continuous +# E.g. rfc2544_throughput, rfc2544_back2back, +# rfc2544_continuous or burst # Data type: str # Default value: "rfc2544_throughput". # 'bidir' - Specifies if generated traffic will be full-duplex (True) @@ -36,6 +36,12 @@ LOG_FILE_TRAFFIC_GEN = 'traffic-gen.log' # continuous stream tests. # Data type: int # Default value: 100. +# 'burst_size' - Defines a number of frames in the single burst, which is sent +# by burst traffic type. Burst size is applied for each direction, +# i.e. the total number of tx frames will be 2*burst_size in case of +# bidirectional traffic. +# Data type: int +# Default value: 100. # 'multistream' - Defines number of flows simulated by traffic generator. # Value 0 disables multistream feature # Data type: int @@ -58,7 +64,6 @@ LOG_FILE_TRAFFIC_GEN = 'traffic-gen.log' # feature. If enabled, it will implicitly insert a flow # for each stream. If multistream is disabled, then # pre-installed flows will be ignored. -# Note: It is supported only for p2p deployment scenario. # Data type: str # Supported values: # "Yes" - flows will be inserted into OVS @@ -112,7 +117,7 @@ LOG_FILE_TRAFFIC_GEN = 'traffic-gen.log' # NOTE: It can be modified by vsperf in some scenarios. # Data type: str # Default value: "90.90.90.90". -# 'proto' - Specifies deflaut protocol type. +# 'proto' - Specifies protocol type. # Please check particular traffic generator implementation # for supported protocol types. # Data type: str @@ -171,9 +176,38 @@ LOG_FILE_TRAFFIC_GEN = 'traffic-gen.log' # details. # Data type: str # Default value: '' +# 'scapy' - A dictionary with definition of a frame content for both traffic +# directions. The frame content is defined by a SCAPY notation. +# NOTE: It is supported only by the T-Rex traffic generator. +# Following keywords can be used to refer to the related parts of +# the TRAFFIC dictionary: +# Ether_src - refers to TRAFFIC['l2']['srcmac'] +# Ether_dst - refers to TRAFFIC['l2']['dstmac'] +# IP_proto - refers to TRAFFIC['l3']['proto'] +# IP_PROTO - refers to upper case version of TRAFFIC['l3']['proto'] +# IP_src - refers to TRAFFIC['l3']['srcip'] +# IP_dst - refers to TRAFFIC['l3']['dstip'] +# IP_PROTO_sport - refers to TRAFFIC['l4']['srcport'] +# IP_PROTO_dport - refers to TRAFFIC['l4']['dstport'] +# Dot1Q_prio - refers to TRAFFIC['vlan']['priority'] +# Dot1Q_id - refers to TRAFFIC['vlan']['cfi'] +# Dot1Q_vlan - refers to TRAFFIC['vlan']['id'] +# '0' - A string with the frame definition for the 1st direction. +# Data type: str +# Default value: 'Ether(src={Ether_src}, dst={Ether_dst})/' +# 'Dot1Q(prio={Dot1Q_prio}, id={Dot1Q_id}, vlan={Dot1Q_vlan})/' +# 'IP(proto={IP_proto}, src={IP_src}, dst={IP_dst})/' +# '{IP_PROTO}(sport={IP_PROTO_sport}, dport={IP_PROTO_dport})' +# '1' - A string with the frame definition for the 2nd direction. +# Data type: str +# Default value: 'Ether(src={Ether_dst}, dst={Ether_src})/' +# 'Dot1Q(prio={Dot1Q_prio}, id={Dot1Q_id}, vlan={Dot1Q_vlan})/' +# 'IP(proto={IP_proto}, src={IP_dst}, dst={IP_src})/' +# '{IP_PROTO}(sport={IP_PROTO_dport}, dport={IP_PROTO_sport})', TRAFFIC = { 'traffic_type' : 'rfc2544_throughput', 'frame_rate' : 100, + 'burst_size' : 100, 'bidir' : 'True', # will be passed as string in title format to tgen 'multistream' : 0, 'stream_type' : 'L4', @@ -210,6 +244,17 @@ TRAFFIC = { 'count': 1, 'filter': '', }, + 'scapy': { + 'enabled': False, + '0' : 'Ether(src={Ether_src}, dst={Ether_dst})/' + 'Dot1Q(prio={Dot1Q_prio}, id={Dot1Q_id}, vlan={Dot1Q_vlan})/' + 'IP(proto={IP_proto}, src={IP_src}, dst={IP_dst})/' + '{IP_PROTO}(sport={IP_PROTO_sport}, dport={IP_PROTO_dport})', + '1' : 'Ether(src={Ether_dst}, dst={Ether_src})/' + 'Dot1Q(prio={Dot1Q_prio}, id={Dot1Q_id}, vlan={Dot1Q_vlan})/' + 'IP(proto={IP_proto}, src={IP_dst}, dst={IP_src})/' + '{IP_PROTO}(sport={IP_PROTO_dport}, dport={IP_PROTO_sport})', + } } #path to traffic generators directory. @@ -487,6 +532,11 @@ TRAFFICGEN_TREX_LEARNING_MODE = True TRAFFICGEN_TREX_LEARNING_DURATION = 5 # FOR SR-IOV or multistream layer 2 tests to work with T-Rex enable Promiscuous mode TRAFFICGEN_TREX_PROMISCUOUS = False +# Enable below options to force T-rex api to attempt to use speed specified on server +# side when pushing traffic. For 40G use 40000. For 25G use 25000. +TRAFFICGEN_TREX_FORCE_PORT_SPEED = False +TRAFFICGEN_TREX_PORT_SPEED = 10000 # 10G + PATHS['trafficgen'] = { 'Trex': { 'type' : 'src', |