vpp: Initial support of VPP vSwitch

Support of VPP was implemented into VSPERF. Initial implementation
uses step driven testcases to configure P2P, PVP and PVVP network
scenarios. These testcases were prepared for three RFC2544 traffic
types, i.e. throughput, continuous stream and back to back.
VPP configuration is driven by new configuration option VSWITCH_VPP_ARGS.
It is possible to use three types of l2 port connection supported
by VPP, i.e. l2 xconnect (default), l2patch and l2 bridge features.
Configuration is driven by parameter VSWITCH_VPP_L2_CONNECT_MODE.

JIRA: VSPERF-495

Change-Id: Idebef9b10fb0d70796adb3405fec77302de00a7e
Signed-off-by: Martin Klozik <martinx.klozik@intel.com>
Reviewed-by: Al Morton <acmorton@att.com>
Reviewed-by: Christian Trautman <ctrautma@redhat.com>
Reviewed-by: Sridhar Rao <sridhar.rao@spirent.com>
Reviewed-by: Trevor Cooper <trevor.cooper@intel.com>

1 files changed, 44 insertions, 5 deletions

diff --git a/docs/userguide/testusage.rst b/docs/userguide/testusage.rst
index 0055164e..c6037aaf 100644
--- a/docs/userguide/testusage.rst
+++ b/docs/userguide/testusage.rst
@@ -335,6 +335,43 @@ To run tests using Vanilla OVS:
 
        $ ./vsperf --conf-file<path_to_custom_conf>/10_custom.conf
 
+.. _vpp-test:
+
+Executing VPP tests
+^^^^^^^^^^^^^^^^^^^
+
+Currently it is not possible to use standard scenario deployments for execution of
+tests with VPP. It means, that deployments ``p2p``, ``pvp``, ``pvvp`` and in general any
+:ref:`pxp-deployment` won't work with VPP. However it is possible to use VPP in
+:ref:`step-driven-tests`. A basic set of VPP testcases covering ``phy2phy``, ``pvp``
+and ``pvvp`` tests are already prepared.
+
+List of performance tests with VPP support follows:
+
+* phy2phy_tput_vpp:              VPP: LTD.Throughput.RFC2544.PacketLossRatio
+* phy2phy_cont_vpp:              VPP: Phy2Phy Continuous Stream
+* phy2phy_back2back_vpp:         VPP: LTD.Throughput.RFC2544.BackToBackFrames
+* pvp_tput_vpp:                  VPP: LTD.Throughput.RFC2544.PacketLossRatio
+* pvp_cont_vpp:                  VPP: PVP Continuous Stream
+* pvp_back2back_vpp:             VPP: LTD.Throughput.RFC2544.BackToBackFrames
+* pvvp_tput_vpp:                 VPP: LTD.Throughput.RFC2544.PacketLossRatio
+* pvvp_cont_vpp:                 VPP: PVP Continuous Stream
+* pvvp_back2back_vpp:            VPP: LTD.Throughput.RFC2544.BackToBackFrames
+
+In order to execute testcases with VPP it is required to:
+
+* install VPP manually, see :ref:`vpp-installation`
+* configure ``WHITELIST_NICS``, with two physical NICs connected to the traffic generator
+* configure traffic generator, see :ref:`trafficgen-installation`
+
+After that it is possible to execute VPP testcases listed above.
+
+For example:
+
+.. code-block:: console
+
+    $ ./vsperf --conf-file=<path_to_custom_conf> phy2phy_tput_vpp
+
 .. _vfio-pci:
 
 Using vfio_pci with DPDK
@@ -689,7 +726,8 @@ application to use the correct number of nb-cores.
 
     .. code-block:: python
 
-        VSWITCHD_DPDK_ARGS = ['-l', '46,44,42,40,38', '-n', '4', '--socket-mem 1024,0']
+        DPDK_SOCKET_MEM = ['1024', '0']
+        VSWITCHD_DPDK_ARGS = ['-l', '46,44,42,40,38', '-n', '4']
         TESTPMD_ARGS = ['--nb-cores=4', '--txq=1', '--rxq=1']
 
 For guest TestPMD 3 VCpus should be assigned with the following TestPMD params.
@@ -790,16 +828,17 @@ an appropriate amount of memory:
 
 .. code-block:: python
 
-    VSWITCHD_DPDK_ARGS = ['-c', '0x4', '-n', '4', '--socket-mem 1024,0']
+    DPDK_SOCKET_MEM = ['1024', '0']
+    VSWITCHD_DPDK_ARGS = ['-c', '0x4', '-n', '4']
     VSWITCHD_DPDK_CONFIG = {
         'dpdk-init' : 'true',
         'dpdk-lcore-mask' : '0x4',
         'dpdk-socket-mem' : '1024,0',
     }
 
-Note: Option VSWITCHD_DPDK_ARGS is used for vswitchd, which supports --dpdk
-parameter. In recent vswitchd versions, option VSWITCHD_DPDK_CONFIG will be
-used to configure vswitchd via ovs-vsctl calls.
+Note: Option ``VSWITCHD_DPDK_ARGS`` is used for vswitchd, which supports ``--dpdk``
+parameter. In recent vswitchd versions, option ``VSWITCHD_DPDK_CONFIG`` will be
+used to configure vswitchd via ``ovs-vsctl`` calls.
 
 
 More information