Moved doc files to testing document structure testing/user ... testing/developer and modified doc index to match dir structure

Change-Id: I4b1a535808a48773505fa7874c61707cd349fced
Signed-off-by: Trevor Cooper <trevor.cooper@intel.com>

1 files changed, 667 insertions, 0 deletions

diff --git a/docs/testing/user/userguide/teststeps.rst b/docs/testing/user/userguide/teststeps.rst
new file mode 100644
index 00000000..870c3d80
--- /dev/null
+++ b/docs/testing/user/userguide/teststeps.rst
@@ -0,0 +1,667 @@
+.. This work is licensed under a Creative Commons Attribution 4.0 International License.
+.. http://creativecommons.org/licenses/by/4.0
+.. (c) OPNFV, Intel Corporation, AT&T and others.
+
+.. _step-driven-tests:
+
+Step driven tests
+=================
+
+In general, test scenarios are defined by a ``deployment`` used in the particular
+test case definition. The chosen deployment scenario will take care of the vSwitch
+configuration, deployment of VNFs and it can also affect configuration of a traffic
+generator. In order to allow a more flexible way of testcase scripting, VSPERF supports
+a detailed step driven testcase definition. It can be used to configure and
+program vSwitch, deploy and terminate VNFs, execute a traffic generator,
+modify a VSPERF configuration, execute external commands, etc.
+
+Execution of step driven tests is done on a step by step work flow starting
+with step 0 as defined inside the test case. Each step of the test increments
+the step number by one which is indicated in the log.
+
+.. code-block:: console
+
+    (testcases.integration) - Step 0 'vswitch add_vport ['br0']' start
+
+Step driven tests can be used for both performance and integration testing.
+In case of integration test, each step in the test case is validated. If a step
+does not pass validation the test will fail and terminate. The test will continue
+until a failure is detected or all steps pass. A csv report file is generated after
+a test completes with an OK or FAIL result.
+
+In case of performance test, the validation of steps is not performed and
+standard output files with results from traffic generator and underlying OS
+details are generated by vsperf.
+
+Step driven testcases can be used in two different ways:
+
+    # description of full testcase - in this case ``clean`` deployment is used
+      to indicate that vsperf should neither configure vSwitch nor deploy any VNF.
+      Test shall perform all required vSwitch configuration and programming and
+      deploy required number of VNFs.
+
+    # modification of existing deployment - in this case, any of supported
+      deployments can be used to perform initial vSwitch configuration and
+      deployment of VNFs. Additional actions defined by TestSteps can be used
+      to alter vSwitch configuration or deploy additional VNFs. After the last
+      step is processed, the test execution will continue with traffic execution.
+
+Test objects and their functions
+--------------------------------
+
+Every test step can call a function of one of the supported test objects. The list
+of supported objects and their most common functions follows:
+
+    * ``vswitch`` - provides functions for vSwitch configuration
+
+      List of supported functions:
+
+        * ``add_switch br_name`` - creates a new switch (bridge) with given ``br_name``
+        * ``del_switch br_name`` - deletes switch (bridge) with given ``br_name``
+        * ``add_phy_port br_name`` - adds a physical port into bridge specified by ``br_name``
+        * ``add_vport br_name`` - adds a virtual port into bridge specified by ``br_name``
+        * ``del_port br_name port_name`` - removes physical or virtual port specified by
+          ``port_name`` from bridge ``br_name``
+        * ``add_flow br_name flow`` - adds flow specified by ``flow`` dictionary into
+          the bridge ``br_name``; Content of flow dictionary will be passed to the vSwitch.
+          In case of Open vSwitch it will be passed to the ``ovs-ofctl add-flow`` command.
+          Please see Open vSwitch documentation for the list of supported flow parameters.
+        * ``del_flow br_name [flow]`` - deletes flow specified by ``flow`` dictionary from
+          bridge ``br_name``; In case that optional parameter ``flow`` is not specified
+          or set to an empty dictionary ``{}``, then all flows from bridge ``br_name``
+          will be deleted.
+        * ``dump_flows br_name`` - dumps all flows from bridge specified by ``br_name``
+        * ``enable_stp br_name`` - enables Spanning Tree Protocol for bridge ``br_name``
+        * ``disable_stp br_name`` - disables Spanning Tree Protocol for bridge ``br_name``
+        * ``enable_rstp br_name`` - enables Rapid Spanning Tree Protocol for bridge ``br_name``
+        * ``disable_rstp br_name`` - disables Rapid Spanning Tree Protocol for bridge ``br_name``
+
+        Examples:
+
+        .. code-block:: python
+
+            ['vswitch', 'add_switch', 'int_br0']
+
+            ['vswitch', 'del_switch', 'int_br0']
+
+            ['vswitch', 'add_phy_port', 'int_br0']
+
+            ['vswitch', 'del_port', 'int_br0', '#STEP[2][0]']
+
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '1', 'actions': ['output:2'],
+             'idle_timeout': '0'}],
+
+            ['vswitch', 'enable_rstp', 'int_br0']
+
+    * ``vnf[ID]`` - provides functions for deployment and termination of VNFs; Optional
+      alfanumerical ``ID`` is used for VNF identification in case that testcase
+      deploys multiple VNFs.
+
+      List of supported functions:
+
+        * ``start`` - starts a VNF based on VSPERF configuration
+        * ``stop`` - gracefully terminates given VNF
+
+        Examples:
+
+        .. code-block:: python
+
+            ['vnf1', 'start']
+            ['vnf2', 'start']
+            ['vnf2', 'stop']
+            ['vnf1', 'stop']
+
+    * ``trafficgen`` - triggers traffic generation
+
+      List of supported functions:
+
+        * ``send_traffic traffic`` - starts a traffic based on the vsperf configuration
+          and given ``traffic`` dictionary. More details about ``traffic`` dictionary
+          and its possible values are available at :ref:`Traffic Generator Integration Guide
+          <step-5-supported-traffic-types>`
+
+        Examples:
+
+        .. code-block:: python
+
+            ['trafficgen', 'send_traffic', {'traffic_type' : 'rfc2544_throughput'}]
+
+            ['trafficgen', 'send_traffic', {'traffic_type' : 'rfc2544_back2back', 'bidir' : 'True'}]
+
+    * ``settings`` - reads or modifies VSPERF configuration
+
+      List of supported functions:
+
+        * ``getValue param`` - returns value of given ``param``
+        * ``setValue param value`` - sets value of ``param`` to given ``value``
+
+        Examples:
+
+        .. code-block:: python
+
+            ['settings', 'getValue', 'TOOLS']
+
+            ['settings', 'setValue', 'GUEST_USERNAME', ['root']]
+
+    * ``namespace`` - creates or modifies network namespaces
+
+      List of supported functions:
+
+        * ``create_namespace name`` - creates new namespace with given ``name``
+        * ``delete_namespace name`` - deletes namespace specified by its ``name``
+        * ``assign_port_to_namespace port name [port_up]`` - assigns NIC specified by ``port``
+          into given namespace ``name``; If optional parameter ``port_up`` is set to ``True``,
+          then port will be brought up.
+        * ``add_ip_to_namespace_eth port name addr cidr`` - assigns an IP address ``addr``/``cidr``
+          to the NIC specified by ``port`` within namespace ``name``
+        * ``reset_port_to_root port name`` - returns given ``port`` from namespace ``name`` back
+          to the root namespace
+
+        Examples:
+
+        .. code-block:: python
+
+            ['namespace', 'create_namespace', 'testns']
+
+            ['namespace', 'assign_port_to_namespace', 'eth0', 'testns']
+
+    * ``veth`` - manipulates with eth and veth devices
+
+      List of supported functions:
+
+        * ``add_veth_port port peer_port`` - adds a pair of veth ports named ``port`` and
+          ``peer_port``
+        * ``del_veth_port port peer_port`` - deletes a veth port pair specified by ``port``
+          and ``peer_port``
+        * ``bring_up_eth_port eth_port [namespace]`` - brings up ``eth_port`` in (optional)
+          ``namespace``
+
+        Examples:
+
+        .. code-block:: python
+
+            ['veth', 'add_veth_port', 'veth', 'veth1']
+
+            ['veth', 'bring_up_eth_port', 'eth1']
+
+    * ``tools`` - provides a set of helper functions
+
+      List of supported functions:
+
+        * ``Assert condition`` - evaluates given ``condition`` and raises ``AssertionError``
+          in case that condition is not ``True``
+        * ``Eval expression`` - evaluates given expression as a python code and returns
+          its result
+        * ``Exec command [regex]`` - executes a shell command and filters its output by
+          (optional) regular expression
+
+        Examples:
+
+        .. code-block:: python
+
+            ['tools', 'exec', 'numactl -H', 'available: ([0-9]+)']
+            ['tools', 'assert', '#STEP[-1][0]>1']
+
+    * ``wait`` - is used for test case interruption. This object doesn't have
+      any functions. Once reached, vsperf will pause test execution and waits
+      for press of ``Enter key``. It can be used during testcase design
+      for debugging purposes.
+
+      Examples:
+
+      .. code-block:: python
+
+        ['wait']
+
+Test Macros
+-----------
+
+Test profiles can include macros as part of the test step. Each step in the
+profile may return a value such as a port name. Recall macros use #STEP to
+indicate the recalled value inside the return structure. If the method the
+test step calls returns a value it can be later recalled, for example:
+
+.. code-block:: python
+
+    {
+        "Name": "vswitch_add_del_vport",
+        "Deployment": "clean",
+        "Description": "vSwitch - add and delete virtual port",
+        "TestSteps": [
+                ['vswitch', 'add_switch', 'int_br0'],               # STEP 0
+                ['vswitch', 'add_vport', 'int_br0'],                # STEP 1
+                ['vswitch', 'del_port', 'int_br0', '#STEP[1][0]'],  # STEP 2
+                ['vswitch', 'del_switch', 'int_br0'],               # STEP 3
+             ]
+    }
+
+This test profile uses the vswitch add_vport method which returns a string
+value of the port added. This is later called by the del_port method using the
+name from step 1.
+
+It is also possible to use negative indexes in step macros. In that case
+``#STEP[-1]`` will refer to the result from previous step, ``#STEP[-2]``
+will refer to result of step called before previous step, etc. It means,
+that you could change ``STEP 2`` from previous example to achieve the same
+functionality:
+
+.. code-block:: python
+
+                ['vswitch', 'del_port', 'int_br0', '#STEP[-1][0]'],  # STEP 2
+
+Also commonly used steps can be created as a separate profile.
+
+.. code-block:: python
+
+    STEP_VSWITCH_PVP_INIT = [
+        ['vswitch', 'add_switch', 'int_br0'],           # STEP 0
+        ['vswitch', 'add_phy_port', 'int_br0'],         # STEP 1
+        ['vswitch', 'add_phy_port', 'int_br0'],         # STEP 2
+        ['vswitch', 'add_vport', 'int_br0'],            # STEP 3
+        ['vswitch', 'add_vport', 'int_br0'],            # STEP 4
+    ]
+
+This profile can then be used inside other testcases
+
+.. code-block:: python
+
+    {
+        "Name": "vswitch_pvp",
+        "Deployment": "clean",
+        "Description": "vSwitch - configure switch and one vnf",
+        "TestSteps": STEP_VSWITCH_PVP_INIT +
+                     [
+                        ['vnf', 'start'],
+                        ['vnf', 'stop'],
+                     ] +
+                     STEP_VSWITCH_PVP_FINIT
+    }
+
+HelloWorld and other basic Testcases
+------------------------------------
+
+The following examples are for demonstration purposes.
+You can run them by copying and pasting into the
+conf/integration/01_testcases.conf file.
+A command-line instruction is shown at the end of each
+example.
+
+HelloWorld
+^^^^^^^^^^
+
+The first example is a HelloWorld testcase.
+It simply creates a bridge with 2 physical ports, then sets up a flow to drop
+incoming packets from the port that was instantiated at the STEP #1.
+There's no interaction with the traffic generator.
+Then the flow, the 2 ports and the bridge are deleted.
+'add_phy_port' method creates a 'dpdk' type interface that will manage the
+physical port. The string value returned is the port name that will be referred
+by 'del_port' later on.
+
+.. code-block:: python
+
+    {
+        "Name": "HelloWorld",
+        "Description": "My first testcase",
+        "Deployment": "clean",
+        "TestSteps": [
+            ['vswitch', 'add_switch', 'int_br0'],   # STEP 0
+            ['vswitch', 'add_phy_port', 'int_br0'], # STEP 1
+            ['vswitch', 'add_phy_port', 'int_br0'], # STEP 2
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'actions': ['drop'], 'idle_timeout': '0'}],
+            ['vswitch', 'del_flow', 'int_br0'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[1][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[2][0]'],
+            ['vswitch', 'del_switch', 'int_br0'],
+        ]
+
+    },
+
+To run HelloWorld test:
+
+  .. code-block:: console
+
+    ./vsperf --conf-file user_settings.py --integration HelloWorld
+
+Specify a Flow by the IP address
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The next example shows how to explicitly set up a flow by specifying a
+destination IP address.
+All packets received from the port created at STEP #1 that have a destination
+IP address = 90.90.90.90 will be forwarded to the port created at the STEP #2.
+
+.. code-block:: python
+
+    {
+        "Name": "p2p_rule_l3da",
+        "Description": "Phy2Phy with rule on L3 Dest Addr",
+        "Deployment": "clean",
+        "biDirectional": "False",
+        "TestSteps": [
+            ['vswitch', 'add_switch', 'int_br0'],   # STEP 0
+            ['vswitch', 'add_phy_port', 'int_br0'], # STEP 1
+            ['vswitch', 'add_phy_port', 'int_br0'], # STEP 2
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'dl_type': '0x0800', 'nw_dst': '90.90.90.90', \
+                'actions': ['output:#STEP[2][1]'], 'idle_timeout': '0'}],
+            ['trafficgen', 'send_traffic', \
+                {'traffic_type' : 'rfc2544_continuous'}],
+            ['vswitch', 'dump_flows', 'int_br0'],   # STEP 5
+            ['vswitch', 'del_flow', 'int_br0'],     # STEP 7 == del-flows
+            ['vswitch', 'del_port', 'int_br0', '#STEP[1][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[2][0]'],
+            ['vswitch', 'del_switch', 'int_br0'],
+        ]
+    },
+
+To run the test:
+
+  .. code-block:: console
+
+    ./vsperf --conf-file user_settings.py --integration p2p_rule_l3da
+
+Multistream feature
+^^^^^^^^^^^^^^^^^^^
+
+The next testcase uses the multistream feature.
+The traffic generator will send packets with different UDP ports.
+That is accomplished by using "Stream Type" and "MultiStream" keywords.
+4 different flows are set to forward all incoming packets.
+
+.. code-block:: python
+
+    {
+        "Name": "multistream_l4",
+        "Description": "Multistream on UDP ports",
+        "Deployment": "clean",
+        "Parameters": {
+            'TRAFFIC' : {
+                "multistream": 4,
+                "stream_type": "L4",
+            },
+        },
+        "TestSteps": [
+            ['vswitch', 'add_switch', 'int_br0'],   # STEP 0
+            ['vswitch', 'add_phy_port', 'int_br0'], # STEP 1
+            ['vswitch', 'add_phy_port', 'int_br0'], # STEP 2
+            # Setup Flows
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'dl_type': '0x0800', 'nw_proto': '17', 'udp_dst': '0', \
+                'actions': ['output:#STEP[2][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'dl_type': '0x0800', 'nw_proto': '17', 'udp_dst': '1', \
+                'actions': ['output:#STEP[2][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'dl_type': '0x0800', 'nw_proto': '17', 'udp_dst': '2', \
+                'actions': ['output:#STEP[2][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'dl_type': '0x0800', 'nw_proto': '17', 'udp_dst': '3', \
+                'actions': ['output:#STEP[2][1]'], 'idle_timeout': '0'}],
+            # Send mono-dir traffic
+            ['trafficgen', 'send_traffic', \
+                {'traffic_type' : 'rfc2544_continuous', \
+                'bidir' : 'False'}],
+            # Clean up
+            ['vswitch', 'del_flow', 'int_br0'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[1][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[2][0]'],
+            ['vswitch', 'del_switch', 'int_br0'],
+         ]
+    },
+
+To run the test:
+
+  .. code-block:: console
+
+    ./vsperf --conf-file user_settings.py --integration multistream_l4
+
+PVP with a VM Replacement
+^^^^^^^^^^^^^^^^^^^^^^^^^
+
+This example launches a 1st VM in a PVP topology, then the VM is replaced
+by another VM.
+When VNF setup parameter in ./conf/04_vnf.conf is "QemuDpdkVhostUser"
+'add_vport' method creates a 'dpdkvhostuser' type port to connect a VM.
+
+.. code-block:: python
+
+    {
+        "Name": "ex_replace_vm",
+        "Description": "PVP with VM replacement",
+        "Deployment": "clean",
+        "TestSteps": [
+            ['vswitch', 'add_switch', 'int_br0'],       # STEP 0
+            ['vswitch', 'add_phy_port', 'int_br0'],     # STEP 1
+            ['vswitch', 'add_phy_port', 'int_br0'],     # STEP 2
+            ['vswitch', 'add_vport', 'int_br0'],        # STEP 3    vm1
+            ['vswitch', 'add_vport', 'int_br0'],        # STEP 4
+
+            # Setup Flows
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'actions': ['output:#STEP[3][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[4][1]', \
+                'actions': ['output:#STEP[2][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[2][1]', \
+                'actions': ['output:#STEP[4][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[3][1]', \
+                'actions': ['output:#STEP[1][1]'], 'idle_timeout': '0'}],
+
+            # Start VM 1
+            ['vnf1', 'start'],
+            # Now we want to replace VM 1 with another VM
+            ['vnf1', 'stop'],
+
+            ['vswitch', 'add_vport', 'int_br0'],        # STEP 11    vm2
+            ['vswitch', 'add_vport', 'int_br0'],        # STEP 12
+            ['vswitch', 'del_flow', 'int_br0'],
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'actions': ['output:#STEP[11][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[12][1]', \
+                'actions': ['output:#STEP[2][1]'], 'idle_timeout': '0'}],
+
+            # Start VM 2
+            ['vnf2', 'start'],
+            ['vnf2', 'stop'],
+            ['vswitch', 'dump_flows', 'int_br0'],
+
+            # Clean up
+            ['vswitch', 'del_flow', 'int_br0'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[1][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[2][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[3][0]'],    # vm1
+            ['vswitch', 'del_port', 'int_br0', '#STEP[4][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[11][0]'],   # vm2
+            ['vswitch', 'del_port', 'int_br0', '#STEP[12][0]'],
+            ['vswitch', 'del_switch', 'int_br0'],
+        ]
+    },
+
+To run the test:
+
+  .. code-block:: console
+
+     ./vsperf --conf-file user_settings.py --integration ex_replace_vm
+
+VM with a Linux bridge
+^^^^^^^^^^^^^^^^^^^^^^
+
+This example setups a PVP topology and routes traffic to the VM based on
+the destination IP address. A command-line parameter is used to select a Linux
+bridge as a guest loopback application. It is also possible to select a guest
+loopback application by a configuration option ``GUEST_LOOPBACK``.
+
+.. code-block:: python
+
+    {
+        "Name": "ex_pvp_rule_l3da",
+        "Description": "PVP with flow on L3 Dest Addr",
+        "Deployment": "clean",
+        "TestSteps": [
+            ['vswitch', 'add_switch', 'int_br0'],       # STEP 0
+            ['vswitch', 'add_phy_port', 'int_br0'],     # STEP 1
+            ['vswitch', 'add_phy_port', 'int_br0'],     # STEP 2
+            ['vswitch', 'add_vport', 'int_br0'],        # STEP 3    vm1
+            ['vswitch', 'add_vport', 'int_br0'],        # STEP 4
+            # Setup Flows
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'dl_type': '0x0800', 'nw_dst': '90.90.90.90', \
+                'actions': ['output:#STEP[3][1]'], 'idle_timeout': '0'}],
+            # Each pkt from the VM is forwarded to the 2nd dpdk port
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[4][1]', \
+                'actions': ['output:#STEP[2][1]'], 'idle_timeout': '0'}],
+            # Start VMs
+            ['vnf1', 'start'],
+            ['trafficgen', 'send_traffic', \
+                {'traffic_type' : 'rfc2544_continuous', \
+                'bidir' : 'False'}],
+            ['vnf1', 'stop'],
+            # Clean up
+            ['vswitch', 'dump_flows', 'int_br0'],       # STEP 10
+            ['vswitch', 'del_flow', 'int_br0'],         # STEP 11
+            ['vswitch', 'del_port', 'int_br0', '#STEP[1][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[2][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[3][0]'],  # vm1 ports
+            ['vswitch', 'del_port', 'int_br0', '#STEP[4][0]'],
+            ['vswitch', 'del_switch', 'int_br0'],
+        ]
+    },
+
+To run the test:
+
+  .. code-block:: console
+
+    ./vsperf --conf-file user_settings.py --test-params \
+            "GUEST_LOOPBACK=['linux_bridge']" --integration ex_pvp_rule_l3da
+
+Forward packets based on UDP port
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+This examples launches 2 VMs connected in parallel.
+Incoming packets will be forwarded to one specific VM depending on the
+destination UDP port.
+
+.. code-block:: python
+
+    {
+        "Name": "ex_2pvp_rule_l4dp",
+        "Description": "2 PVP with flows on L4 Dest Port",
+        "Deployment": "clean",
+        "Parameters": {
+            'TRAFFIC' : {
+                "multistream": 2,
+                "stream_type": "L4",
+            },
+        },
+        "TestSteps": [
+            ['vswitch', 'add_switch', 'int_br0'],       # STEP 0
+            ['vswitch', 'add_phy_port', 'int_br0'],     # STEP 1
+            ['vswitch', 'add_phy_port', 'int_br0'],     # STEP 2
+            ['vswitch', 'add_vport', 'int_br0'],        # STEP 3    vm1
+            ['vswitch', 'add_vport', 'int_br0'],        # STEP 4
+            ['vswitch', 'add_vport', 'int_br0'],        # STEP 5    vm2
+            ['vswitch', 'add_vport', 'int_br0'],        # STEP 6
+            # Setup Flows to reply ICMPv6 and similar packets, so to
+            # avoid flooding internal port with their re-transmissions
+            ['vswitch', 'add_flow', 'int_br0', \
+                {'priority': '1', 'dl_src': '00:00:00:00:00:01', \
+                'actions': ['output:#STEP[3][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', \
+                {'priority': '1', 'dl_src': '00:00:00:00:00:02', \
+                'actions': ['output:#STEP[4][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', \
+                {'priority': '1', 'dl_src': '00:00:00:00:00:03', \
+                'actions': ['output:#STEP[5][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', \
+                {'priority': '1', 'dl_src': '00:00:00:00:00:04', \
+                'actions': ['output:#STEP[6][1]'], 'idle_timeout': '0'}],
+            # Forward UDP packets depending on dest port
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'dl_type': '0x0800', 'nw_proto': '17', 'udp_dst': '0', \
+                'actions': ['output:#STEP[3][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[1][1]', \
+                'dl_type': '0x0800', 'nw_proto': '17', 'udp_dst': '1', \
+                'actions': ['output:#STEP[5][1]'], 'idle_timeout': '0'}],
+            # Send VM output to phy port #2
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[4][1]', \
+                'actions': ['output:#STEP[2][1]'], 'idle_timeout': '0'}],
+            ['vswitch', 'add_flow', 'int_br0', {'in_port': '#STEP[6][1]', \
+                'actions': ['output:#STEP[2][1]'], 'idle_timeout': '0'}],
+            # Start VMs
+            ['vnf1', 'start'],                          # STEP 16
+            ['vnf2', 'start'],                          # STEP 17
+            ['trafficgen', 'send_traffic', \
+                {'traffic_type' : 'rfc2544_continuous', \
+                'bidir' : 'False'}],
+            ['vnf1', 'stop'],
+            ['vnf2', 'stop'],
+            ['vswitch', 'dump_flows', 'int_br0'],
+            # Clean up
+            ['vswitch', 'del_flow', 'int_br0'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[1][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[2][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[3][0]'],  # vm1 ports
+            ['vswitch', 'del_port', 'int_br0', '#STEP[4][0]'],
+            ['vswitch', 'del_port', 'int_br0', '#STEP[5][0]'],  # vm2 ports
+            ['vswitch', 'del_port', 'int_br0', '#STEP[6][0]'],
+            ['vswitch', 'del_switch', 'int_br0'],
+        ]
+    },
+
+To run the test:
+
+  .. code-block:: console
+
+    ./vsperf --conf-file user_settings.py --integration ex_2pvp_rule_l4dp
+
+Modification of existing PVVP deployment
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+This is an example of modification of a standard deployment scenario with additional TestSteps.
+Standard PVVP scenario is used to configure a vSwitch and to deploy two VNFs connected
+in series. Additional TestSteps will deploy a 3rd VNF and connect it in parallel to
+already configured VNFs. Traffic generator is instructed (by Multistream feature) to send
+two separate traffic streams. One stream will be sent to the standalone VNF and second
+to two chained VNFs.
+
+In case, that test is defined as a performance test, then traffic results will be collected
+and available in both csv and rst report files.
+
+.. code-block:: python
+
+    {
+        "Name": "pvvp_pvp_cont",
+        "Deployment": "pvvp",
+        "Description": "PVVP and PVP in parallel with Continuous Stream",
+        "Parameters" : {
+            "TRAFFIC" : {
+                "traffic_type" : "rfc2544_continuous",
+                "multistream": 2,
+            },
+        },
+        "TestSteps": [
+                        ['vswitch', 'add_vport', 'br0'],
+                        ['vswitch', 'add_vport', 'br0'],
+                        # priority must be higher than default 32768, otherwise flows won't match
+                        ['vswitch', 'add_flow', 'br0',
+                         {'in_port': '1', 'actions': ['output:#STEP[-2][1]'], 'idle_timeout': '0', 'dl_type':'0x0800',
+                                                      'nw_proto':'17', 'tp_dst':'0', 'priority': '33000'}],
+                        ['vswitch', 'add_flow', 'br0',
+                         {'in_port': '2', 'actions': ['output:#STEP[-2][1]'], 'idle_timeout': '0', 'dl_type':'0x0800',
+                                                      'nw_proto':'17', 'tp_dst':'0', 'priority': '33000'}],
+                        ['vswitch', 'add_flow', 'br0', {'in_port': '#STEP[-4][1]', 'actions': ['output:1'],
+                                                        'idle_timeout': '0'}],
+                        ['vswitch', 'add_flow', 'br0', {'in_port': '#STEP[-4][1]', 'actions': ['output:2'],
+                                                        'idle_timeout': '0'}],
+                        ['vswitch', 'dump_flows', 'br0'],
+                        ['vnf1', 'start'],
+                     ]
+    },
+
+To run the test:
+
+  .. code-block:: console
+
+    ./vsperf --conf-file user_settings.py pvvp_pvp_cont
+