Add L3 traffic management with Neutron routers

Change-Id: Ic9bff87e0d78652de28b3a756f9ebc342983cfbb
Signed-off-by: fmenguy <francoisregis.menguy@orange.com>

1 files changed, 66 insertions, 0 deletions

diff --git a/docs/testing/user/userguide/pvpl3.rst b/docs/testing/user/userguide/pvpl3.rst
new file mode 100644
index 0000000..12f1d86
--- /dev/null
+++ b/docs/testing/user/userguide/pvpl3.rst
@@ -0,0 +1,66 @@
+.. This work is licensed under a Creative Commons Attribution 4.0 International License.
+.. SPDX-License-Identifier: CC-BY-4.0
+.. (c) Cisco Systems, Inc
+
+
+PVP L3 Router Internal Chain
+--------------
+
+NFVbench can measure the performance of 1 L3 service chain that are setup by NFVbench (VMs, routers and networks).
+
+PVP L3 router chain is made of 1 VNF (in vpp mode) and has exactly 2 end network interfaces (left and right internal network interfaces) that are connected to 2 neutron routers with 2 edge networks (left and right edge networks).
+The PVP L3 router service chain can route L3 packets properly between the left and right networks.
+
+To run NFVbench on such PVP L3 router service chain:
+
+- explicitly tell NFVbench to use PVP service chain with L3 router option by adding ``-l3`` or ``--l3-router`` to NFVbench CLI options or ``l3_router: true`` in config
+- explicitly tell NFVbench to use VPP forwarder with ``vm_forwarder: vpp`` in config
+- specify the 2 end point networks (networks between NFVBench and neutron routers) of your environment in ``internal_networks`` inside the config file.
+    - The two networks specified will be created if not existing in Neutron and will be used as the end point networks by NFVbench ('lyon' and 'bordeaux' in the diagram below)
+- specify the 2 edge networks (networks between neutron routers and loopback VM) of your environment in ``edge_networks`` inside the config file.
+    - The two networks specified will be created if not existing in Neutron and will be used as the router gateway networks by NFVbench ('paris' and 'marseille' in the diagram below)
+- specify the router gateway IPs for the PVPL3 router service chain (1.2.0.1 and 2.2.0.1)
+- specify the traffic generator gateway IPs for the PVPL3 router service chain (1.2.0.254 and 2.2.0.254 in diagram below)
+- specify the packet source and destination IPs for the virtual devices that are simulated (10.0.0.0/8 and 20.0.0.0/8)
+
+
+.. image:: images/nfvbench-pvpl3.png
+
+nfvbench configuration file:
+
+.. code-block:: bash
+
+    vm_forwarder: vpp
+
+    traffic_generator:
+        ip_addrs: ['10.0.0.0/8', '20.0.0.0/8']
+        tg_gateway_ip_addrs: ['1.2.0.254', '2.2.0.254']
+        gateway_ip_addrs: ['1.2.0.1', '2.2.0.1']
+
+    internal_networks:
+        left:
+            name: 'lyon'
+            cidr: '1.2.0.0/24'
+            gateway: '1.2.0.1'
+        right:
+            name: 'bordeaux'
+            cidr: '2.2.0.0/24'
+            gateway: '2.2.0.1'
+
+    edge_networks:
+        left:
+            name: 'paris'
+            cidr: '1.1.0.0/24'
+            gateway: '1.1.0.1'
+        right:
+            name: 'marseille'
+            cidr: '2.1.0.0/24'
+            gateway: '2.1.0.1'
+
+Upon start, NFVbench will:
+- first retrieve the properties of the left and right networks using Neutron APIs,
+- extract the underlying network ID (typically VLAN segmentation ID),
+- generate packets with the proper VLAN ID and measure traffic.
+
+
+Please note: ``l3_router`` option is also compatible with external routers. In this case NFVBench will use ``EXT`` chain.
\ No newline at end of file