1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
|
/*
* Copyright (C) 2009 Texas Instruments Incorporated
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* Spectrum Digital TMS320DM365 EVM board */
#define DAVINCI_DM365EVM
#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 3rd stage loader */
#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
#define CONFIG_SYS_CONSOLE_INFO_QUIET
/* SoC Configuration */
#define CONFIG_ARM926EJS /* arm926ejs CPU */
#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
#define CONFIG_SYS_HZ_CLOCK 24000000 /* timer0 freq */
#define CONFIG_SOC_DM365
/* Memory Info */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x80000000
#define PHYS_SDRAM_1_SIZE (128 << 20) /* 128 MiB */
/* Serial Driver info: UART0 for console */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE -4
#define CONFIG_SYS_NS16550_COM1 0x01c20000
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
/* EEPROM definitions for EEPROM on DM365 EVM */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
/* Network Configuration */
#define CONFIG_DRIVER_TI_EMAC
#define CONFIG_MII
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_DAVINCI
#define CONFIG_SYS_DAVINCI_I2C_SPEED 400000
#define CONFIG_SYS_DAVINCI_I2C_SLAVE 0x10 /* SMBus host address */
/* NAND: socketed, two chipselects, normally 2 GBytes */
#define CONFIG_NAND_DAVINCI
#define CONFIG_SYS_NAND_CS 2
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
#define CONFIG_SYS_NAND_PAGE_2K
#define CONFIG_SYS_NAND_LARGEPAGE
#define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, }
/* socket has two chipselects, nCE0 gated by address BIT(14) */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_MAX_CHIPS 2
/* SD/MMC */
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_DAVINCI_MMC
#define CONFIG_DAVINCI_MMC_SD1
#define CONFIG_MMC_MBLOCK
#define PINMUX4_USBDRVBUS_BITCLEAR 0x3000
#define PINMUX4_USBDRVBUS_BITSET 0x2000
/* USB Configuration */
#define CONFIG_USB_DAVINCI
#define CONFIG_MUSB_HCD
#ifdef CONFIG_USB_DAVINCI
#define CONFIG_CMD_USB /* include support for usb */
#define CONFIG_CMD_STORAGE /* include support for usb */
#define CONFIG_CMD_FAT /* include support for FAT/storage*/
#define CONFIG_DOS_PARTITION /* include support for FAT/storage*/
#endif
#ifdef CONFIG_MUSB_HCD /* include support for usb host */
#define CONFIG_CMD_USB /* include support for usb cmd */
#define CONFIG_USB_STORAGE /* MSC class support */
#define CONFIG_CMD_STORAGE /* inclue support for usb-storage cmd */
#define CONFIG_CMD_FAT /* inclue support for FAT/storage */
#define CONFIG_DOS_PARTITION /* inclue support for FAT/storage */
#ifdef CONFIG_USB_KEYBOARD /* HID class support */
#define CONFIG_SYS_USB_EVENT_POLL
#define CONFIG_PREBOOT "usb start"
#endif /* CONFIG_USB_KEYBOARD */
#endif /* CONFIG_MUSB_HCD */
#ifdef CONFIG_MUSB_UDC
#define CONFIG_USB_DEVICE 1
#define CONFIG_USB_TTY 1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
#define CONFIG_USBD_VENDORID 0x0451
#define CONFIG_USBD_PRODUCTID 0x5678
#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
#define CONFIG_USBD_PRODUCT_NAME "DM365VM"
#endif /* CONFIG_MUSB_UDC */
/* U-Boot command configuration */
#include <config_cmd_default.h>
#undef CONFIG_CMD_BDI
#undef CONFIG_CMD_FLASH
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_SETGETDCR
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_I2C
#define CONFIG_CMD_PING
#define CONFIG_CMD_SAVES
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#ifdef CONFIG_MMC
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_MMC
#endif
#ifdef CONFIG_NAND_DAVINCI
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_PARTITIONS
#define CONFIG_MTD_DEVICE
#define CONFIG_CMD_NAND
#define CONFIG_CMD_UBI
#define CONFIG_RBTREE
#endif
#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
/* U-Boot general configuration */
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
#define CONFIG_SYS_PROMPT "DM36x EVM # " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE /* Print buffer size */ \
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_LONGHELP
#ifdef CONFIG_NAND_DAVINCI
#define CONFIG_ENV_SIZE (256 << 10) /* 256 KiB */
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0x3C0000
#undef CONFIG_ENV_IS_IN_FLASH
#endif
#if defined(CONFIG_MMC) && !defined(CONFIG_ENV_IS_IN_NAND)
#define CONFIG_CMD_ENV
#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
#define CONFIG_ENV_OFFSET (51 << 9) /* Sector 51 */
#define CONFIG_ENV_IS_IN_MMC
#undef CONFIG_ENV_IS_IN_FLASH
#endif
#define CONFIG_BOOTDELAY 3
#define CONFIG_BOOTCOMMAND \
"dhcp;bootm"
#define CONFIG_BOOTARGS \
"console=ttyS0,115200n8 " \
"root=/dev/mmcblk0p1 rootwait rootfstype=ext3 ro"
#define CONFIG_CMDLINE_EDITING
#define CONFIG_VERSION_VARIABLE
#define CONFIG_TIMESTAMP
/* U-Boot memory configuration */
#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* 1 MiB */
#define CONFIG_SYS_MEMTEST_START 0x87000000 /* physical address */
#define CONFIG_SYS_MEMTEST_END 0x88000000 /* test 16MB RAM */
/* Linux interfacing */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_SYS_BARGSIZE 1024 /* bootarg Size */
#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* kernel address */
/* NAND configuration issocketed with two chipselects just like the DM355 EVM.
* It normally comes with a 2GByte SLC part with 2KB pages
* (and 128KB erase blocks); other
* 2GByte parts may have 4KB pages, 256KB erase blocks, and use MLC. (MLC
* pretty much demands the 4-bit ECC support.) You can of course swap in
* other parts, including small page ones.
*/
#define MTDIDS_DEFAULT "nand0=davinci_nand.0"
#ifdef CONFIG_SYS_NAND_LARGEPAGE
/* Use same layout for 128K/256K blocks; allow some bad blocks */
#define PART_BOOT "2m(bootloader)ro,"
#else
/* Assume 16K erase blocks; allow a few bad ones. */
#define PART_BOOT "512k(bootloader)ro,"
#endif
#define PART_KERNEL "4m(kernel)," /* kernel + initramfs */
#define PART_REST "-(filesystem)"
#define MTDPARTS_DEFAULT \
"mtdparts=davinci_nand.0:" PART_BOOT PART_KERNEL PART_REST
#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
#endif /* __CONFIG_H */
|
