1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
|
/*
* SPDX-License-Identifier: GPL-2.0 IBM-pibs
*/
#include <config.h>
#include <asm/ppc4xx.h>
#include <ppc_asm.tmpl>
#include <ppc_defs.h>
#include <asm/cache.h>
#include <asm/mmu.h>
#define LI32(reg,val) \
addis reg,0,val@h;\
ori reg,reg,val@l
#define WDCR_EBC(reg,val) \
addi r4,0,reg;\
mtdcr EBC0_CFGADDR,r4;\
addis r4,0,val@h;\
ori r4,r4,val@l;\
mtdcr EBC0_CFGDATA,r4
#define WDCR_SDRAM(reg,val) \
addi r4,0,reg;\
mtdcr SDRAM0_CFGADDR,r4;\
addis r4,0,val@h;\
ori r4,r4,val@l;\
mtdcr SDRAM0_CFGDATA,r4
/******************************************************************************
* Function: ext_bus_cntlr_init
*
* Description: Configures EBC Controller and a few basic chip selects.
*
* CS0 is setup to get the Boot Flash out of the addresss range
* so that we may setup a stack. CS7 is setup so that we can
* access and reset the hardware watchdog.
*
* IMPORTANT: For pass1 this code must run from
* cache since you can not reliably change a peripheral banks
* timing register (pbxap) while running code from that bank.
* For ex., since we are running from ROM on bank 0, we can NOT
* execute the code that modifies bank 0 timings from ROM, so
* we run it from cache.
*
* Notes: Does NOT use the stack.
*****************************************************************************/
.section ".text"
.align 2
.globl ext_bus_cntlr_init
.type ext_bus_cntlr_init, @function
ext_bus_cntlr_init:
mflr r0
/********************************************************************
* Prefetch entire ext_bus_cntrl_init function into the icache.
* This is necessary because we are going to change the same CS we
* are executing from. Otherwise a CPU lockup may occur.
*******************************************************************/
bl ..getAddr
..getAddr:
mflr r3 /* get address of ..getAddr */
/* Calculate number of cache lines for this function */
addi r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2)
mtctr r4
..ebcloop:
icbt r0, r3 /* prefetch cache line for addr in r3*/
addi r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */
bdnz ..ebcloop /* continue for $CTR cache lines */
/********************************************************************
* Delay to ensure all accesses to ROM are complete before changing
* bank 0 timings. 200usec should be enough.
* 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles.
*******************************************************************/
addis r3, 0, 0x0
ori r3, r3, 0xA000 /* wait 200us from reset */
mtctr r3
..spinlp:
bdnz ..spinlp /* spin loop */
/********************************************************************
* SETUP CPC0_CR0
*******************************************************************/
LI32(r4, 0x007000c0)
mtdcr CPC0_CR0, r4
/********************************************************************
* Setup CPC0_CR1: Change PCIINT signal to PerWE
*******************************************************************/
mfdcr r4, CPC0_CR1
ori r4, r4, 0x4000
mtdcr CPC0_CR1, r4
/********************************************************************
* Setup External Bus Controller (EBC).
*******************************************************************/
WDCR_EBC(EBC0_CFG, 0xd84c0000)
/********************************************************************
* Memory Bank 0 (Intel 28F128J3 Flash) initialization
*******************************************************************/
/*WDCR_EBC(PB1AP, 0x02869200)*/
WDCR_EBC(PB1AP, 0x07869200)
WDCR_EBC(PB0CR, 0xfe0bc000)
/********************************************************************
* Memory Bank 1 (Holtek HT6542B PS/2) initialization
*******************************************************************/
WDCR_EBC(PB1AP, 0x1f869200)
WDCR_EBC(PB1CR, 0xf0818000)
/********************************************************************
* Memory Bank 2 (Epson S1D13506) initialization
*******************************************************************/
WDCR_EBC(PB2AP, 0x05860300)
WDCR_EBC(PB2CR, 0xf045a000)
/********************************************************************
* Memory Bank 3 (Philips SJA1000 CAN Controllers) initialization
*******************************************************************/
WDCR_EBC(PB3AP, 0x0387d200)
WDCR_EBC(PB3CR, 0xf021c000)
/********************************************************************
* Memory Bank 4-7 (Unused) initialization
*******************************************************************/
WDCR_EBC(PB4AP, 0)
WDCR_EBC(PB4CR, 0)
WDCR_EBC(PB5AP, 0)
WDCR_EBC(PB5CR, 0)
WDCR_EBC(PB6AP, 0)
WDCR_EBC(PB6CR, 0)
WDCR_EBC(PB7AP, 0)
WDCR_EBC(PB7CR, 0)
/* We are all done */
mtlr r0 /* Restore link register */
blr /* Return to calling function */
.Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init
/* end ext_bus_cntlr_init() */
/******************************************************************************
* Function: sdram_init
*
* Description: Configures SDRAM memory banks.
*
* Notes: Does NOT use the stack.
*****************************************************************************/
.section ".text"
.align 2
.globl sdram_init
.type sdram_init, @function
sdram_init:
/*
* Disable memory controller to allow
* values to be changed.
*/
WDCR_SDRAM(SDRAM0_CFG, 0x00000000)
/*
* Configure Memory Banks
*/
WDCR_SDRAM(SDRAM0_B0CR, 0x00084001)
WDCR_SDRAM(SDRAM0_B1CR, 0x00000000)
WDCR_SDRAM(SDRAM0_B2CR, 0x00000000)
WDCR_SDRAM(SDRAM0_B3CR, 0x00000000)
/*
* Set up SDTR1 (SDRAM Timing Register)
*/
WDCR_SDRAM(SDRAM0_TR, 0x00854009)
/*
* Set RTR (Refresh Timing Register)
*/
WDCR_SDRAM(SDRAM0_RTR, 0x10000000)
/* WDCR_SDRAM(SDRAM0_RTR, 0x05f00000) */
/********************************************************************
* Delay to ensure 200usec have elapsed since reset. Assume worst
* case that the core is running 200Mhz:
* 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles
*******************************************************************/
addis r3, 0, 0x0000
ori r3, r3, 0xA000 /* Wait >200us from reset */
mtctr r3
..spinlp2:
bdnz ..spinlp2 /* spin loop */
/********************************************************************
* Set memory controller options reg, MCOPT1.
*******************************************************************/
WDCR_SDRAM(SDRAM0_CFG,0x80800000)
..sdri_done:
blr /* Return to calling function */
.Lfe1: .size sdram_init,.Lfe1-sdram_init
/* end sdram_init() */
|
