1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
|
/*
* Device Tree for the ST-Ericsson Nomadik S8815 board
* Produced by Calao Systems
*/
/dts-v1/;
#include <dt-bindings/interrupt-controller/irq.h>
#include "ste-nomadik-stn8815.dtsi"
/ {
model = "Calao Systems USB-S8815";
compatible = "calaosystems,usb-s8815";
chosen {
bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
};
aliases {
serial0 = &uart0;
serial1 = &uart1;
};
gpio3: gpio@101e7000 {
/* This hog will bias the MMC/SD card detect line */
mmcsd-gpio {
gpio-hog;
gpios = <16 0x0>;
output-low;
line-name = "card detect bias";
};
};
src@101e0000 {
/* These chrystal drivers are not used on this board */
disable-sxtalo;
disable-mxtalo;
};
pinctrl {
/* Hog CD pins */
pinctrl-names = "default";
pinctrl-0 = <&cd_default_mode>;
uart0 {
/* Only use RX/TX pins */
uart0_s8815_mode: uart0_mux {
u0_default_mux {
function = "u0";
groups = "u0txrx_a_1";
};
};
};
mmcsd-cd {
cd_default_mode: cd_default {
cd_default_cfg1 {
/* CD input GPIO */
pins = "GPIO111_H21";
ste,input = <0>;
};
cd_default_cfg2 {
/* CD GPIO biasing */
pins = "GPIO112_J21";
ste,output = <0>;
};
};
};
gpioi2c {
gpioi2c_default_mode: gpioi2c_default {
gpioi2c_default_cfg {
pins = "GPIO73_C21", "GPIO74_C20";
ste,input = <0>;
};
};
};
user-led {
user_led_default_mode: user_led_default {
user_led_default_cfg {
pins = "GPIO2_C5";
ste,output = <1>;
};
};
};
user-button {
user_button_default_mode: user_button_default {
user_button_default_cfg {
pins = "GPIO3_A4";
ste,input = <0>;
};
};
};
};
/* Ethernet */
external-bus@34000000 {
compatible = "simple-bus";
reg = <0x34000000 0x1000000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x34000000 0x1000000>;
ethernet@300 {
compatible = "smsc,lan91c111";
reg = <0x300 0x0fd00>;
interrupt-parent = <&gpio3>;
interrupts = <8 IRQ_TYPE_EDGE_RISING>;
};
};
i2c1 {
lis3lv02dl@1d {
/* Accelerometer */
compatible = "st,lis3lv02dl-accel";
reg = <0x1d>;
};
};
/* GPIO I2C connected to the USB portions of the STw4811 only */
gpio-i2c {
compatible = "i2c-gpio";
gpios = <&gpio2 10 0>, /* sda */
<&gpio2 9 0>; /* scl */
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&gpioi2c_default_mode>;
stw4811@2d {
compatible = "st,stw4811-usb";
reg = <0x2d>;
};
};
amba {
/* Activate RXTX on UART 0 */
uart0: uart@101fd000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_s8815_mode>;
status = "okay";
};
/* Configure card detect for the uSD slot */
mmcsd: sdi@101f6000 {
cd-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
};
};
/* The user LED on the board is set up to be used for heartbeat */
leds {
compatible = "gpio-leds";
user-led {
label = "user_led";
gpios = <&gpio0 2 0x1>;
default-state = "off";
linux,default-trigger = "heartbeat";
pinctrl-names = "default";
pinctrl-0 = <&user_led_default_mode>;
};
};
/* User key mapped in as "escape" */
gpio-keys {
compatible = "gpio-keys";
user-button {
label = "user_button";
gpios = <&gpio0 3 0x1>;
linux,code = <1>; /* KEY_ESC */
gpio-key,wakeup;
pinctrl-names = "default";
pinctrl-0 = <&user_button_default_mode>;
};
};
};
|
