diff options
Diffstat (limited to 'qemu/roms/u-boot/include/status_led.h')
| -rw-r--r-- | qemu/roms/u-boot/include/status_led.h | 324 |
1 files changed, 0 insertions, 324 deletions
diff --git a/qemu/roms/u-boot/include/status_led.h b/qemu/roms/u-boot/include/status_led.h deleted file mode 100644 index ecff60d59..000000000 --- a/qemu/roms/u-boot/include/status_led.h +++ /dev/null @@ -1,324 +0,0 @@ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * The purpose of this code is to signal the operational status of a - * target which usually boots over the network; while running in - * PCBoot, a status LED is blinking. As soon as a valid BOOTP reply - * message has been received, the LED is turned off. The Linux - * kernel, once it is running, will start blinking the LED again, - * with another frequency. - */ - -#ifndef _STATUS_LED_H_ -#define _STATUS_LED_H_ - -#ifdef CONFIG_STATUS_LED - -#define STATUS_LED_OFF 0 -#define STATUS_LED_BLINKING 1 -#define STATUS_LED_ON 2 - -void status_led_tick (unsigned long timestamp); -void status_led_set (int led, int state); - -/***** TQM8xxL ********************************************************/ -#if defined(CONFIG_TQM8xxL) -# define STATUS_LED_PAR im_cpm.cp_pbpar -# define STATUS_LED_DIR im_cpm.cp_pbdir -# define STATUS_LED_ODR im_cpm.cp_pbodr -# define STATUS_LED_DAT im_cpm.cp_pbdat - -# define STATUS_LED_BIT 0x00000001 -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -/***** MVS v1 **********************************************************/ -#elif (defined(CONFIG_MVS) && CONFIG_MVS < 2) -# define STATUS_LED_PAR im_ioport.iop_pdpar -# define STATUS_LED_DIR im_ioport.iop_pddir -# undef STATUS_LED_ODR -# define STATUS_LED_DAT im_ioport.iop_pddat - -# define STATUS_LED_BIT 0x00000001 -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -/***** GEN860T *********************************************************/ -#elif defined(CONFIG_GEN860T) - -# define STATUS_LED_PAR im_ioport.iop_papar -# define STATUS_LED_DIR im_ioport.iop_padir -# define STATUS_LED_ODR im_ioport.iop_paodr -# define STATUS_LED_DAT im_ioport.iop_padat - -# define STATUS_LED_BIT 0x0800 /* Red LED 0 is on PA.4 */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) -# define STATUS_LED_STATE STATUS_LED_OFF -# define STATUS_LED_BIT1 0x0400 /* Grn LED 1 is on PA.5 */ -# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 8) -# define STATUS_LED_STATE1 STATUS_LED_BLINKING -# define STATUS_LED_BIT2 0x0080 /* Red LED 2 is on PA.8 */ -# define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 4) -# define STATUS_LED_STATE2 STATUS_LED_OFF -# define STATUS_LED_BIT3 0x0040 /* Grn LED 3 is on PA.9 */ -# define STATUS_LED_PERIOD3 (CONFIG_SYS_HZ / 4) -# define STATUS_LED_STATE3 STATUS_LED_OFF - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ -# define STATUS_LED_BOOT 1 /* Boot status on LED 1 */ - -/***** IVMS8 **********************************************************/ -#elif defined(CONFIG_IVMS8) - -# define STATUS_LED_PAR im_cpm.cp_pbpar -# define STATUS_LED_DIR im_cpm.cp_pbdir -# define STATUS_LED_ODR im_cpm.cp_pbodr -# define STATUS_LED_DAT im_cpm.cp_pbdat - -# define STATUS_LED_BIT 0x00000010 /* LED 0 is on PB.27 */ -# define STATUS_LED_PERIOD (1 * CONFIG_SYS_HZ) -# define STATUS_LED_STATE STATUS_LED_OFF -# define STATUS_LED_BIT1 0x00000020 /* LED 1 is on PB.26 */ -# define STATUS_LED_PERIOD1 (1 * CONFIG_SYS_HZ) -# define STATUS_LED_STATE1 STATUS_LED_OFF -/* IDE LED usable for other purposes, too */ -# define STATUS_LED_BIT2 0x00000008 /* LED 2 is on PB.28 */ -# define STATUS_LED_PERIOD2 (1 * CONFIG_SYS_HZ) -# define STATUS_LED_STATE2 STATUS_LED_OFF - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_ILOCK_SWITCH 0x00800000 /* ILOCK switch in IRQ4 */ - -# define STATUS_ILOCK_PERIOD (CONFIG_SYS_HZ / 10) /* about every 100 ms */ - -# define STATUS_LED_YELLOW 0 -# define STATUS_LED_GREEN 1 -# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */ - -/***** IVML24 *********************************************************/ -#elif defined(CONFIG_IVML24) - -# define STATUS_LED_PAR im_cpm.cp_pbpar -# define STATUS_LED_DIR im_cpm.cp_pbdir -# define STATUS_LED_ODR im_cpm.cp_pbodr -# define STATUS_LED_DAT im_cpm.cp_pbdat - -# define STATUS_LED_BIT 0x00000010 /* LED 0 is on PB.27 */ -# define STATUS_LED_PERIOD (1 * CONFIG_SYS_HZ) -# define STATUS_LED_STATE STATUS_LED_OFF -# define STATUS_LED_BIT1 0x00000020 /* LED 1 is on PB.26 */ -# define STATUS_LED_PERIOD1 (1 * CONFIG_SYS_HZ) -# define STATUS_LED_STATE1 STATUS_LED_OFF -/* IDE LED usable for other purposes, too */ -# define STATUS_LED_BIT2 0x00000008 /* LED 2 is on PB.28 */ -# define STATUS_LED_PERIOD2 (1 * CONFIG_SYS_HZ) -# define STATUS_LED_STATE2 STATUS_LED_OFF - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_ILOCK_SWITCH 0x00004000 /* ILOCK is on PB.17 */ - -# define STATUS_ILOCK_PERIOD (CONFIG_SYS_HZ / 10) /* about every 100 ms */ - -# define STATUS_LED_YELLOW 0 -# define STATUS_LED_GREEN 1 -# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */ - -/***** ICU862 ********************************************************/ -#elif defined(CONFIG_ICU862) - -# define STATUS_LED_PAR im_ioport.iop_papar -# define STATUS_LED_DIR im_ioport.iop_padir -# define STATUS_LED_ODR im_ioport.iop_paodr -# define STATUS_LED_DAT im_ioport.iop_padat - -# define STATUS_LED_BIT 0x4000 /* LED 0 is on PA.1 */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING -# define STATUS_LED_BIT1 0x1000 /* LED 1 is on PA.3 */ -# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ) -# define STATUS_LED_STATE1 STATUS_LED_OFF - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -/***** Someone else defines these *************************************/ -#elif defined(STATUS_LED_PAR) - - /* - * ADVICE: Define in your board configuration file rather than - * filling this file up with lots of custom board stuff. - */ - -/***** NetVia ********************************************************/ -#elif defined(CONFIG_NETVIA) - -#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1 - -#define STATUS_LED_PAR im_ioport.iop_pdpar -#define STATUS_LED_DIR im_ioport.iop_pddir -#undef STATUS_LED_ODR -#define STATUS_LED_DAT im_ioport.iop_pddat - -# define STATUS_LED_BIT 0x0080 /* PD.8 */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_BIT1 0x0040 /* PD.9 */ -# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE1 STATUS_LED_OFF - -# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -#endif - -/***** CMI ********************************************************/ -#elif defined(CONFIG_CMI) -# define STATUS_LED_DIR im_mios.mios_mpiosm32ddr -# define STATUS_LED_DAT im_mios.mios_mpiosm32dr - -# define STATUS_LED_BIT 0x2000 /* Select one of the 16 possible*/ - /* MIOS outputs */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) /* Blinking periode is 500 ms */ -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 0 */ -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -/***** KUP4K, KUP4X ****************************************************/ -#elif defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X) - -# define STATUS_LED_PAR im_ioport.iop_papar -# define STATUS_LED_DIR im_ioport.iop_padir -# define STATUS_LED_ODR im_ioport.iop_paodr -# define STATUS_LED_DAT im_ioport.iop_padat - -# define STATUS_LED_BIT 0x00000300 /* green + red PA[8]=yellow, PA[7]=red, PA[6]=green */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -#elif defined(CONFIG_SVM_SC8xx) -# define STATUS_LED_PAR im_cpm.cp_pbpar -# define STATUS_LED_DIR im_cpm.cp_pbdir -# define STATUS_LED_ODR im_cpm.cp_pbodr -# define STATUS_LED_DAT im_cpm.cp_pbdat - -# define STATUS_LED_BIT 0x00000001 -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -/***** RBC823 ********************************************************/ -#elif defined(CONFIG_RBC823) - -# define STATUS_LED_PAR im_ioport.iop_pcpar -# define STATUS_LED_DIR im_ioport.iop_pcdir -# undef STATUS_LED_ODR -# define STATUS_LED_DAT im_ioport.iop_pcdat - -# define STATUS_LED_BIT 0x0002 /* LED 0 is on PC.14 */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING -# define STATUS_LED_BIT1 0x0004 /* LED 1 is on PC.13 */ -# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ) -# define STATUS_LED_STATE1 STATUS_LED_OFF - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -/***** NetPhone ********************************************************/ -#elif defined(CONFIG_NETPHONE) || defined(CONFIG_NETTA2) -/* XXX empty just to avoid the error */ -/***** STx XTc ********************************************************/ -#elif defined(CONFIG_STXXTC) -/* XXX empty just to avoid the error */ -/************************************************************************/ -#elif defined(CONFIG_V38B) - -# define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */ -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -#elif defined(CONFIG_MOTIONPRO) - -#define STATUS_LED_BIT ((vu_long *) MPC5XXX_GPT6_ENABLE) -#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 10) -#define STATUS_LED_STATE STATUS_LED_BLINKING - -#define STATUS_LED_BIT1 ((vu_long *) MPC5XXX_GPT7_ENABLE) -#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 10) -#define STATUS_LED_STATE1 STATUS_LED_OFF - -#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -#elif defined(CONFIG_BOARD_SPECIFIC_LED) -/* led_id_t is unsigned long mask */ -typedef unsigned long led_id_t; - -extern void __led_toggle (led_id_t mask); -extern void __led_init (led_id_t mask, int state); -extern void __led_set (led_id_t mask, int state); -#else -# error Status LED configuration missing -#endif -/************************************************************************/ - -#ifndef CONFIG_BOARD_SPECIFIC_LED -# include <asm/status_led.h> -#endif - -/* - * Coloured LEDs API - */ -#ifndef __ASSEMBLY__ -extern void coloured_LED_init (void); -extern void red_led_on(void); -extern void red_led_off(void); -extern void green_led_on(void); -extern void green_led_off(void); -extern void yellow_led_on(void); -extern void yellow_led_off(void); -extern void blue_led_on(void); -extern void blue_led_off(void); -#else - .extern LED_init - .extern red_led_on - .extern red_led_off - .extern yellow_led_on - .extern yellow_led_off - .extern green_led_on - .extern green_led_off - .extern blue_led_on - .extern blue_led_off -#endif - -#endif /* CONFIG_STATUS_LED */ - -#endif /* _STATUS_LED_H_ */ |