diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/woodburn_common.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/woodburn_common.h | 296 |
1 files changed, 0 insertions, 296 deletions
diff --git a/qemu/roms/u-boot/include/configs/woodburn_common.h b/qemu/roms/u-boot/include/configs/woodburn_common.h deleted file mode 100644 index 695bc230c..000000000 --- a/qemu/roms/u-boot/include/configs/woodburn_common.h +++ /dev/null @@ -1,296 +0,0 @@ -/* - * (C) Copyright 2011, Stefano Babic <sbabic@denx.de> - * - * (C) Copyright 2008-2010 Freescale Semiconductor, Inc. - * - * Configuration for the woodburn board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __WOODBURN_COMMON_CONFIG_H -#define __WOODBURN_COMMON_CONFIG_H - -#include <asm/arch/imx-regs.h> - - /* High Level Configuration Options */ -#define CONFIG_ARM1136 /* This is an arm1136 CPU core */ -#define CONFIG_MX35 -#define CONFIG_MX35_HCLK_FREQ 24000000 - -#define CONFIG_SYS_DCACHE_OFF -#define CONFIG_SYS_CACHELINE_SIZE 32 - -#define CONFIG_DISPLAY_CPUINFO - -/* Only in case the value is not present in mach-types.h */ -#ifndef MACH_TYPE_FLEA3 -#define MACH_TYPE_FLEA3 3668 -#endif - -#define CONFIG_MACH_TYPE MACH_TYPE_FLEA3 - -/* This is required to setup the ESDC controller */ - -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_REVISION_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024) - -/* - * Hardware drivers - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_SPD_BUS_NUM 0 -#define CONFIG_MXC_SPI -#define CONFIG_MXC_GPIO - -/* PMIC Controller */ -#define CONFIG_POWER -#define CONFIG_POWER_I2C -#define CONFIG_POWER_FSL -#define CONFIG_PMIC_FSL_MC13892 -#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8 -#define CONFIG_RTC_MC13XXX - - -/* mmc driver */ -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_FSL_ESDHC -#define CONFIG_SYS_FSL_ESDHC_ADDR 0 -#define CONFIG_SYS_FSL_ESDHC_NUM 1 - -/* - * UART (console) - */ -#define CONFIG_MXC_UART -#define CONFIG_MXC_UART_BASE UART1_BASE - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 115200 - -/* - * Command definition - */ - -#include <config_cmd_default.h> - -#define CONFIG_CMD_PING -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_DNS - -#define CONFIG_CMD_NAND -#define CONFIG_CMD_CACHE - -#define CONFIG_CMD_I2C -#define CONFIG_CMD_SPI -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET - -#define CONFIG_CMD_MMC -#define CONFIG_DOS_PARTITION -#define CONFIG_EFI_PARTITION -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT - -#define CONFIG_CMD_GPIO -#define CONFIG_MXC_GPIO - -#define CONFIG_NET_RETRY_COUNT 100 - -#define CONFIG_BOOTDELAY 3 - -#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */ - - -/* - * Ethernet on SOC (FEC) - */ -#define CONFIG_FEC_MXC -#define IMX_FEC_BASE FEC_BASE_ADDR -#define CONFIG_PHYLIB -#define CONFIG_PHY_MICREL -#define CONFIG_FEC_MXC_PHYADDR 0x1 - -#define CONFIG_MII -#define CONFIG_DISCOVER_PHY - -#define CONFIG_ARP_TIMEOUT 200UL - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "woodburn U-Boot > " -#define CONFIG_CMDLINE_EDITING -#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */ - -#define CONFIG_AUTO_COMPLETE -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x10000 - -#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */ - -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR - -/* - * Stack sizes - * - * The stack sizes are set up in start.S using the settings below - */ -#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ - -/* - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 CSD0_BASE_ADDR -#define PHYS_SDRAM_1_SIZE (256 * 1024 * 1024) - -#define CONFIG_SYS_SDRAM_BASE CSD0_BASE_ADDR - -#define CONFIG_SYS_GBL_DATA_OFFSET (LOW_LEVEL_SRAM_STACK - \ - IRAM_BASE_ADDR - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR (IRAM_BASE_ADDR + \ - CONFIG_SYS_GBL_DATA_OFFSET) - -/* - * MTD Command for mtdparts - */ -#define CONFIG_CMD_MTDPARTS -#define CONFIG_MTD_DEVICE -#define CONFIG_FLASH_CFI_MTD -#define CONFIG_MTD_PARTITIONS -#define MTDIDS_DEFAULT "nand0=mxc_nand,nor0=physmap-flash.0" -#define MTDPARTS_DEFAULT "mtdparts=mxc_nand:50m(root1)," \ - "32m(rootfb)," \ - "64m(pcache)," \ - "64m(app1)," \ - "10m(app2),-(spool);" \ - "physmap-flash.0:512k(u-boot),64k(env1)," \ - "64k(env2),3776k(kernel1),3776k(kernel2)" - -/* - * FLASH and environment organization - */ -#define CONFIG_SYS_FLASH_BASE CS0_BASE_ADDR -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ -/* Monitor at beginning of flash */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) - -#define CONFIG_ENV_SECT_SIZE (128 * 1024) -#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) - -#define CONFIG_ENV_IS_IN_FLASH - -/* - * CFI FLASH driver setup - */ -#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */ -#define CONFIG_FLASH_CFI_DRIVER - -/* A non-standard buffered write algorithm */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* faster */ -#define CONFIG_SYS_FLASH_PROTECTION /* Use hardware sector protection */ - -/* - * NAND FLASH driver setup - */ -#define CONFIG_NAND_MXC -#define CONFIG_NAND_MXC_V1_1 -#define CONFIG_MXC_NAND_REGS_BASE (NFC_BASE_ADDR) -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE (NFC_BASE_ADDR) -#define CONFIG_MXC_NAND_HWECC -#define CONFIG_SYS_NAND_LARGEPAGE - -#if 0 -#define CONFIG_MTD_DEBUG -#define CONFIG_MTD_DEBUG_VERBOSE 7 -#endif -#define CONFIG_SYS_NAND_ONFI_DETECTION - -/* - * Default environment and default scripts - * to update uboot and load kernel - */ -#define xstr(s) str(s) -#define str(s) #s - -#define CONFIG_HOSTNAME woodburn -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip_sta=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \ - "addip=if test -n ${ipdyn};then run addip_dyn;" \ - "else run addip_sta;fi\0" \ - "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ - "addtty=setenv bootargs ${bootargs}" \ - " console=ttymxc0,${baudrate}\0" \ - "addmisc=setenv bootargs ${bootargs} ${misc}\0" \ - "loadaddr=80800000\0" \ - "kernel_addr_r=80800000\0" \ - "hostname=" xstr(CONFIG_HOSTNAME) "\0" \ - "bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \ - "ramdisk_file=" xstr(CONFIG_HOSTNAME) "/uRamdisk\0" \ - "flash_self=run ramargs addip addtty addmtd addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ - "bootm ${kernel_addr}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ - "run nfsargs addip addtty addmtd addmisc;" \ - "bootm ${kernel_addr_r}\0" \ - "net_self_load=tftp ${kernel_addr_r} ${bootfile};" \ - "tftp ${ramdisk_addr_r} ${ramdisk_file};\0" \ - "net_self=if run net_self_load;then " \ - "run ramargs addip addtty addmtd addmisc;" \ - "bootm ${kernel_addr_r} ${ramdisk_addr_r};" \ - "else echo Images not loades;fi\0" \ - "u-boot=" xstr(CONFIG_HOSTNAME) "/u-boot.bin\0" \ - "load=tftp ${loadaddr} ${u-boot}\0" \ - "uboot_addr=" xstr(CONFIG_SYS_MONITOR_BASE) "\0" \ - "update=protect off ${uboot_addr} +80000;" \ - "erase ${uboot_addr} +80000;" \ - "cp.b ${loadaddr} ${uboot_addr} ${filesize}\0" \ - "upd=if run load;then echo Updating u-boot;if run update;" \ - "then echo U-Boot updated;" \ - "else echo Error updating u-boot !;" \ - "echo Board without bootloader !!;" \ - "fi;" \ - "else echo U-Boot not downloaded..exiting;fi\0" \ - "bootcmd=run net_nfs\0" - -#endif /* __CONFIG_H */ |