diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/ve8313.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/ve8313.h | 498 |
1 files changed, 498 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/ve8313.h b/qemu/roms/u-boot/include/configs/ve8313.h new file mode 100644 index 000000000..00787bbb2 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/ve8313.h @@ -0,0 +1,498 @@ +/* + * Copyright (C) Freescale Semiconductor, Inc. 2006. + * + * (C) Copyright 2010 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ +/* + * ve8313 board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 +#define CONFIG_MPC831x 1 +#define CONFIG_MPC8313 1 +#define CONFIG_VE8313 1 + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xfe000000 +#endif + +#define CONFIG_PCI 1 +#define CONFIG_PCI_INDIRECT_BRIDGE 1 +#define CONFIG_FSL_ELBC 1 + +#define CONFIG_BOARD_EARLY_INIT_F 1 + +/* + * On-board devices + * + */ +#define CONFIG_83XX_CLKIN 32000000 /* in Hz */ + +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN + +#define CONFIG_SYS_IMMR 0xE0000000 + +#define CONFIG_SYS_MEMTEST_START 0x00001000 +#define CONFIG_SYS_MEMTEST_END 0x07000000 + +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count */ + +/* + * Device configurations + */ + +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE + +/* + * Manually set up DDR parameters, as this board does not + * have the SPD connected to I2C. + */ +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ + | CSCONFIG_AP \ + | CSCONFIG_ODT_RD_NEVER \ + | CSCONFIG_ODT_WR_ALL \ + | CSCONFIG_ROW_BIT_13 \ + | CSCONFIG_COL_BIT_10) + /* 0x80840102 */ + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ + | (0 << TIMING_CFG0_WRT_SHIFT) \ + | (3 << TIMING_CFG0_RRT_SHIFT) \ + | (2 << TIMING_CFG0_WWT_SHIFT) \ + | (7 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ + | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) + /* 0x0e720802 */ +#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ + | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ + | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ + | (5 << TIMING_CFG1_CASLAT_SHIFT) \ + | (6 << TIMING_CFG1_REFREC_SHIFT) \ + | (2 << TIMING_CFG1_WRREC_SHIFT) \ + | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ + | (2 << TIMING_CFG1_WRTORD_SHIFT)) + /* 0x26256222 */ +#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ + | (5 << TIMING_CFG2_CPO_SHIFT) \ + | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ + | (1 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ + | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ + | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ + | (7 << TIMING_CFG2_FOUR_ACT_SHIFT)) + /* 0x029028c7 */ +#define CONFIG_SYS_DDR_INTERVAL ((0x320 << SDRAM_INTERVAL_REFINT_SHIFT) \ + | (0x2000 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + /* 0x03202000 */ +#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_DBW_32) + /* 0x43080000 */ +#define CONFIG_SYS_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) \ + | (0x0232 << SDRAM_MODE_SD_SHIFT)) + /* 0x44400232 */ +#define CONFIG_SYS_DDR_MODE_2 0x8000C000 + +#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 + /*0x02000000*/ +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ + | DDRCDR_PZ_NOMZ \ + | DDRCDR_NZ_NOMZ \ + | DDRCDR_M_ODR) + /* 0x73000002 */ + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 +#define CONFIG_SYS_FLASH_SIZE 32 /* size in MB */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */ + +#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \ + | BR_PS_16 /* 16 bit */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV4 \ + | OR_GPCM_SCY_5 \ + | OR_GPCM_TRLX_SET \ + | OR_GPCM_EAD) + /* 0xfe000c55 */ + +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per dev */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ + +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) + +/* + * Local Bus LCRR and LBCR regs + */ +#define CONFIG_SYS_LCRR_EADC LCRR_EADC_3 +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 + +#define CONFIG_SYS_LBC_LBCR 0x00040000 + +#define CONFIG_SYS_LBC_MRTPR 0x20000000 + +/* + * NAND settings + */ +#define CONFIG_SYS_NAND_BASE 0x61000000 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND 1 +#define CONFIG_NAND_FSL_ELBC 1 +#define CONFIG_SYS_NAND_BLOCK_SIZE 16384 + +#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \ + | BR_PS_8 \ + | BR_DECC_CHK_GEN \ + | BR_MS_FCM \ + | BR_V) /* valid */ + /* 0x61000c21 */ +#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB \ + | OR_FCM_BCTLD \ + | OR_FCM_CHT \ + | OR_FCM_SCY_2 \ + | OR_FCM_RST \ + | OR_FCM_TRLX) + /* 0xffff90ac */ + +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM + +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) + +#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM +#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM + +/* CS2 NvRAM */ +#define CONFIG_SYS_BR2_PRELIM (0x60000000 \ + | BR_PS_8 \ + | BR_V) + /* 0x60000801 */ +#define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB \ + | OR_GPCM_CSNT \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_3 \ + | OR_GPCM_TRLX_SET \ + | OR_GPCM_EHTR_SET \ + | OR_GPCM_EAD) + /* 0xfffe0937 */ +/* local bus read write buffer mapping SRAM@0x64000000 */ +#define CONFIG_SYS_BR3_PRELIM (0x62000000 \ + | BR_PS_16 \ + | BR_V) + /* 0x62001001 */ + +#define CONFIG_SYS_OR3_PRELIM (OR_AM_32MB \ + | OR_GPCM_CSNT \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX_SET \ + | OR_GPCM_EHTR_SET \ + | OR_GPCM_EAD) + /* 0xfe0009f7 */ + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +#if defined(CONFIG_PCI) +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE +#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#endif + +/* + * TSEC + */ +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ + + +#define CONFIG_TSEC1 +#ifdef CONFIG_TSEC1 +#define CONFIG_HAS_ETH0 +#define CONFIG_TSEC1_NAME "TSEC1" +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define TSEC1_PHY_ADDR 0x01 +#define TSEC1_FLAGS 0 +#define TSEC1_PHYIDX 0 +#endif + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC1" + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR \ + (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x4000 +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_OFFSET_REDUND \ + (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_PCI + +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ + +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg Buffer size */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ + /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) + +/* 0x64050000 */ +#define CONFIG_SYS_HRCW_LOW (\ + 0x20000000 /* reserved, must be set */ |\ + HRCWL_DDRCM |\ + HRCWL_CSB_TO_CLKIN_4X1 | \ + HRCWL_CORE_TO_CSB_2_5X1) + +/* 0xa0600004 */ +#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \ + HRCWH_PCI_ARBITER_ENABLE | \ + HRCWH_CORE_ENABLE | \ + HRCWH_FROM_0X00000100 | \ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT | \ + HRCWH_TSEC1M_IN_MII | \ + HRCWH_BIG_ENDIAN | \ + HRCWH_LALE_EARLY) + +/* System IO Config */ +#define CONFIG_SYS_SICRH (0x01000000 | \ + SICRH_ETSEC2_B | \ + SICRH_ETSEC2_C | \ + SICRH_ETSEC2_D | \ + SICRH_ETSEC2_E | \ + SICRH_ETSEC2_F | \ + SICRH_ETSEC2_G | \ + SICRH_TSOBI1 | \ + SICRH_TSOBI2) + /* 0x010fff03 */ +#define CONFIG_SYS_SICRL (SICRL_LBC | \ + SICRL_SPI_A | \ + SICRL_SPI_B | \ + SICRL_SPI_C | \ + SICRL_SPI_D | \ + SICRL_ETSEC2_A) + /* 0x33fc0003) */ + +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ + HID0_ENABLE_INSTRUCTION_CACHE) + +#define CONFIG_SYS_HID2 HID2_HBE + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* DDR @ 0x00000000 */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) + +#if defined(CONFIG_PCI) +/* PCI @ 0x80000000 */ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#else +#define CONFIG_SYS_IBAT1L (0) +#define CONFIG_SYS_IBAT1U (0) +#define CONFIG_SYS_IBAT2L (0) +#define CONFIG_SYS_IBAT2U (0) +#endif + +/* PCI2 not supported on 8313 */ +#define CONFIG_SYS_IBAT3L (0) +#define CONFIG_SYS_IBAT3U (0) +#define CONFIG_SYS_IBAT4L (0) +#define CONFIG_SYS_IBAT4U (0) + +/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) + +/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ +#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +/* FPGA, SRAM, NAND @ 0x60000000 */ +#define CONFIG_SYS_IBAT7L (0x60000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT7U (0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U +#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U +#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U +#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U + +#define CONFIG_NETDEV eth0 + +#define CONFIG_HOSTNAME ve8313 +#define CONFIG_UBOOTPATH ve8313/u-boot.bin + +#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=" __stringify(CONFIG_NETDEV) "\0" \ + "ethprime=" __stringify(CONFIG_TSEC1_NAME) "\0" \ + "u-boot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "u-boot_addr_r=100000\0" \ + "load=tftp ${u-boot_addr_r} ${u-boot}\0" \ + "update=protect off " __stringify(CONFIG_SYS_FLASH_BASE) \ + " +${filesize};" \ + "erase " __stringify(CONFIG_SYS_FLASH_BASE) " +${filesize};" \ + "cp.b ${u-boot_addr_r} " __stringify(CONFIG_SYS_FLASH_BASE) \ + " ${filesize};" \ + "protect on " __stringify(CONFIG_SYS_FLASH_BASE) " +${filesize}\0" \ + +#endif /* __CONFIG_H */ |