diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/v38b.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/v38b.h | 336 |
1 files changed, 0 insertions, 336 deletions
diff --git a/qemu/roms/u-boot/include/configs/v38b.h b/qemu/roms/u-boot/include/configs/v38b.h deleted file mode 100644 index 7f6b0c7cb..000000000 --- a/qemu/roms/u-boot/include/configs/v38b.h +++ /dev/null @@ -1,336 +0,0 @@ -/* - * (C) Copyright 2003-2006 Wolfgang Denk, DENX Software Engineering, - * wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_V38B 1 /* ...on V38B board */ - -#define CONFIG_SYS_TEXT_BASE 0xFF000000 - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ...running at 33.000000MHz */ - -#define CONFIG_RTC_PCF8563 1 /* has PCF8563 RTC */ -#define CONFIG_MPC5200_DDR 1 /* has DDR SDRAM */ - -#undef CONFIG_HW_WATCHDOG /* don't use watchdog */ - -#define CONFIG_NETCONSOLE 1 - -#define CONFIG_BOARD_EARLY_INIT_R 1 /* do board-specific init */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* do board-specific init */ -#define CONFIG_MISC_INIT_R - -#define CONFIG_SYS_XLB_PIPELINING 1 /* gives better performance */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * DDR - */ -#define SDRAM_DDR 1 /* is DDR */ -/* Settings for XLB = 132 MHz */ -#define SDRAM_MODE 0x018D0000 -#define SDRAM_EMODE 0x40090000 -#define SDRAM_CONTROL 0x704f0f00 -#define SDRAM_CONFIG1 0x73722930 -#define SDRAM_CONFIG2 0x47770000 -#define SDRAM_TAPDELAY 0x10000000 - -/* - * PCI - no suport - */ -#undef CONFIG_PCI - -/* - * Partitions - */ -#define CONFIG_MAC_PARTITION 1 -#define CONFIG_DOS_PARTITION 1 - -/* - * USB - */ -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_DATE -#define CONFIG_CMD_USB -#define CONFIG_CMD_FAT - - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - -/* - * Boot low with 16 MB Flash - */ -#define CONFIG_SYS_LOWBOOT 1 -#define CONFIG_SYS_LOWBOOT16 1 - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "bootcmd=run net_nfs\0" \ - "bootdelay=3\0" \ - "baudrate=115200\0" \ - "preboot=echo;echo Type \"run flash_nfs\" to mount root " \ - "filesystem over NFS; echo\0" \ - "netdev=eth0\0" \ - "ramargs=setenv bootargs root=/dev/ram rw wdt=off \0" \ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):" \ - "$(netmask):$(hostname):$(netdev):off panic=1\0" \ - "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \ - "flash_self=run ramargs addip;bootm $(kernel_addr) " \ - "$(ramdisk_addr)\0" \ - "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath) wdt=off\0" \ - "hostname=v38b\0" \ - "ethact=FEC\0" \ - "rootpath=/opt/eldk-3.1.1/ppc_6xx\0" \ - "update=prot off ff000000 ff03ffff; era ff000000 ff03ffff; " \ - "cp.b 200000 ff000000 $(filesize);" \ - "prot on ff000000 ff03ffff\0" \ - "load=tftp 200000 $(u-boot)\0" \ - "netmask=255.255.0.0\0" \ - "ipaddr=192.168.160.18\0" \ - "serverip=192.168.1.1\0" \ - "ethaddr=00:e0:ee:00:05:2e\0" \ - "bootfile=/tftpboot/v38b/uImage\0" \ - "u-boot=/tftpboot/v38b/u-boot.bin\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run net_nfs" - -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * RTC configuration - */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - -/* - * Flash configuration - use CFI driver - */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 -#define CONFIG_SYS_FLASH_BASE 0xFF000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CONFIG_SYS_FLASH_SIZE 0x01000000 /* 16 MiB */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* flash write speed-up */ - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000) -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x10000 -#define CONFIG_ENV_OVERWRITE 1 - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Linux initial memory map */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -#define CONFIG_PHY_ADDR 0x00 -#define CONFIG_MII 1 - -/* - * GPIO configuration - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x90001404 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00047801 -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/* - * IDE/ATA (supports IDE harddisk) - */ -#undef CONFIG_IDE_8xx_PCCARD /* Don't use IDE with PC Card Adapter */ -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) /* data I/O offset */ - -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* normal register accesses offset */ - -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) /* alternate registers offset */ - -#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ - -/* - * Status LED - */ -#define CONFIG_STATUS_LED /* Status LED enabled */ -#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ - -#define CONFIG_SYS_LED_BASE MPC5XXX_GPT7_ENABLE /* Timer 7 GPIO */ -#ifndef __ASSEMBLY__ -typedef unsigned int led_id_t; - -#define __led_toggle(_msk) \ - do { \ - *((volatile long *) (CONFIG_SYS_LED_BASE)) ^= (_msk); \ - } while(0) - -#define __led_set(_msk, _st) \ - do { \ - if ((_st)) \ - *((volatile long *) (CONFIG_SYS_LED_BASE)) &= ~(_msk); \ - else \ - *((volatile long *) (CONFIG_SYS_LED_BASE)) |= (_msk); \ - } while(0) - -#define __led_init(_msk, st) \ - do { \ - *((volatile long *) (CONFIG_SYS_LED_BASE)) |= 0x34; \ - } while(0) -#endif /* __ASSEMBLY__ */ - -#endif /* __CONFIG_H */ |