diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/stxgp3.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/stxgp3.h | 364 |
1 files changed, 364 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/stxgp3.h b/qemu/roms/u-boot/include/configs/stxgp3.h new file mode 100644 index 000000000..5fb40ebf8 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/stxgp3.h @@ -0,0 +1,364 @@ +/* + * (C) Copyright 2003 Embedded Edge, LLC + * Dan Malek <dan@embeddededge.com> + * Copied from ADS85xx. + * Updates for Silicon Tx GP3 8560 board. + * + * (C) Copyright 2002,2003 Motorola,Inc. + * Xianghua Xiao <X.Xiao@motorola.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* mpc8560ads board configuration file */ +/* please refer to doc/README.mpc85xx for more info */ +/* make sure you change the MAC address and other network params first, + * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_CPM2 1 /* has CPM2 */ +#define CONFIG_STXGP3 1 /* Silicon Tx GPPP board specific*/ +#define CONFIG_MPC8560 1 + +#define CONFIG_SYS_TEXT_BASE 0xfff80000 + +#undef CONFIG_PCI /* pci ethernet support */ +#define CONFIG_TSEC_ENET /* tsec ethernet support*/ +#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +/* sysclk for MPC85xx + */ + +#define CONFIG_SYS_CLK_FREQ 33333333 /* most pci cards are 33Mhz */ + +/* Blinkin' LEDs for Robert :-) +*/ +#define CONFIG_SHOW_ACTIVITY 1 + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ + +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 + + +/* Localbus SDRAM is an option, not all boards have it. + * This address, however, is used to configure a 256M local bus + * window that includes the Config latch below. + */ +#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CONFIG_SYS_LBC_SDRAM_SIZE 256 /* LBC SDRAM is 64MB */ + +#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ +#define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */ + +#define CONFIG_SYS_OR0_PRELIM 0xff000ff7 /* 16 MB Flash */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 136 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +/* The configuration latch is Chip Select 1. + * It's an 8-bit latch in the lower 8 bits of the word. + */ +#define CONFIG_SYS_BR1_PRELIM 0xfc001801 /* 32-bit port */ +#define CONFIG_SYS_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ +#define CONFIG_SYS_LBC_LCLDEVS_BASE 0xfc000000 /* Base of localbus devices */ + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + +#ifdef CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ +#endif +#define CONFIG_SYS_CCSRBAR 0xfdf00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR + +/* DDR Setup */ +#define CONFIG_SYS_FSL_DDR1 +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ +#define CONFIG_DDR_SPD +#undef CONFIG_FSL_DDR_INTERACTIVE + +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */ +#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) + +/* I2C addresses of SPD EEPROMs */ +#define SPD_EEPROM_ADDRESS 0x54 /* CTLR 0 DIMM 0 */ + +#undef CONFIG_CLOCKS_IN_MHZ + +/* local bus definitions */ +#define CONFIG_SYS_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ +#define CONFIG_SYS_OR2_PRELIM 0xfc006901 +#define CONFIG_SYS_LBC_LCRR 0x00030004 /* local bus freq */ +#define CONFIG_SYS_LBC_LBCR 0x00000000 +#define CONFIG_SYS_LBC_LSRT 0x20000000 +#define CONFIG_SYS_LBC_MRTPR 0x20000000 +#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723 +#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723 +#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723 +#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723 +#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723 + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ + +#define CONFIG_BAUDRATE 38400 + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#endif + +/* + * I2C + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 + +#if 0 +#define CONFIG_SYS_I2C_NOPROBES {0x00} /* Don't probe these addrs */ +#else +/* I did the 'if 0' so we could keep the syntax above if ever needed. */ +#undef CONFIG_SYS_I2C_NOPROBES +#endif + +/* RapdIO Map configuration, mapped 1:1. +*/ +#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 +#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE +#define CONFIG_SYS_RIO_MEM_SIZE 0x200000000 /* 512 M */ + +/* Standard 8560 PCI addressing, mapped 1:1. +*/ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCI1_IO_BASE 0xe2000000 +#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE +#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16 M */ + +#if defined(CONFIG_PCI) /* PCI Ethernet card */ + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR 0xe0000000 + #define PCI_ENET0_MEMADDR 0xe0000000 + #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ +#endif + +#undef CONFIG_PCI_SCAN_SHOW +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +#endif /* CONFIG_PCI */ + +#if defined(CONFIG_TSEC_ENET) + +#define CONFIG_MII 1 /* MII PHY management */ + +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "TSEC1" + +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 4 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT +#define CONFIG_ETHPRIME "TSEC0" + +#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ + +#define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 2 /* which channel for ether */ + +#if (CONFIG_ETHER_INDEX == 2) + /* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - Select bus for bd/buffers + * - Full duplex + */ + #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) + #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) + #define CONFIG_SYS_CPMFCR_RAMTYPE 0 +#if 0 + #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE) +#else + #define CONFIG_SYS_FCC_PSMR 0 +#endif + #define FETH2_RST 0x01 +#elif (CONFIG_ETHER_INDEX == 3) + /* need more definitions here for FE3 */ + #define FETH3_RST 0x80 +#endif /* CONFIG_ETHER_INDEX */ + +/* MDIO is done through the TSEC0 control. +*/ +#define CONFIG_MII /* MII PHY management */ +#undef CONFIG_BITBANGMII /* bit-bang MII PHY management */ + +#endif + +/* Environment */ +/* We use the top boot sector flash, so we have some 16K sectors for env + */ +#ifndef CONFIG_SYS_RAMBOOT + #define CONFIG_ENV_IS_IN_FLASH 1 + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x60000) + #define CONFIG_ENV_SECT_SIZE 0x4000 /* 16K (one top sector) for env */ + #define CONFIG_ENV_SIZE 0x2000 +#else + #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ + #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) + #define CONFIG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400" +#define CONFIG_BOOTCOMMAND "bootm 0xff000000 0xff100000" +#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_REGINFO + +#if defined(CONFIG_SYS_RAMBOOT) + #undef CONFIG_CMD_SAVEENV + #undef CONFIG_CMD_LOADS +#else + #define CONFIG_CMD_ELF +#endif + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) + #define CONFIG_CMD_MII +#endif + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "GPPP=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#endif + +/*Note: change below for your network setting!!! */ +#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) +#define CONFIG_HAS_ETH0 +#define CONFIG_ETHADDR 00:e0:0c:07:9b:8a +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b +#define CONFIG_HAS_ETH2 +#define CONFIG_ETH2ADDR 00:e0:0c:07:9b:8c +#endif + +#define CONFIG_SERVERIP 192.168.85.1 +#define CONFIG_IPADDR 192.168.85.60 +#define CONFIG_GATEWAYIP 192.168.85.1 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_HOSTNAME STX_GP3 +#define CONFIG_ROOTPATH "/gppproot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_LOADADDR 0x1000000 + +#endif /* __CONFIG_H */ |