diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/stxgp3.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/stxgp3.h | 364 |
1 files changed, 0 insertions, 364 deletions
diff --git a/qemu/roms/u-boot/include/configs/stxgp3.h b/qemu/roms/u-boot/include/configs/stxgp3.h deleted file mode 100644 index 5fb40ebf8..000000000 --- a/qemu/roms/u-boot/include/configs/stxgp3.h +++ /dev/null @@ -1,364 +0,0 @@ -/* - * (C) Copyright 2003 Embedded Edge, LLC - * Dan Malek <dan@embeddededge.com> - * Copied from ADS85xx. - * Updates for Silicon Tx GP3 8560 board. - * - * (C) Copyright 2002,2003 Motorola,Inc. - * Xianghua Xiao <X.Xiao@motorola.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* mpc8560ads board configuration file */ -/* please refer to doc/README.mpc85xx for more info */ -/* make sure you change the MAC address and other network params first, - * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* High Level Configuration Options */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_CPM2 1 /* has CPM2 */ -#define CONFIG_STXGP3 1 /* Silicon Tx GPPP board specific*/ -#define CONFIG_MPC8560 1 - -#define CONFIG_SYS_TEXT_BASE 0xfff80000 - -#undef CONFIG_PCI /* pci ethernet support */ -#define CONFIG_TSEC_ENET /* tsec ethernet support*/ -#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ - -/* sysclk for MPC85xx - */ - -#define CONFIG_SYS_CLK_FREQ 33333333 /* most pci cards are 33Mhz */ - -/* Blinkin' LEDs for Robert :-) -*/ -#define CONFIG_SHOW_ACTIVITY 1 - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ - -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00400000 - - -/* Localbus SDRAM is an option, not all boards have it. - * This address, however, is used to configure a 256M local bus - * window that includes the Config latch below. - */ -#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ -#define CONFIG_SYS_LBC_SDRAM_SIZE 256 /* LBC SDRAM is 64MB */ - -#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ -#define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */ - -#define CONFIG_SYS_OR0_PRELIM 0xff000ff7 /* 16 MB Flash */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 136 /* sectors per device */ -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* The configuration latch is Chip Select 1. - * It's an 8-bit latch in the lower 8 bits of the word. - */ -#define CONFIG_SYS_BR1_PRELIM 0xfc001801 /* 32-bit port */ -#define CONFIG_SYS_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ -#define CONFIG_SYS_LBC_LCLDEVS_BASE 0xfc000000 /* Base of localbus devices */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#ifdef CONFIG_SYS_RAMBOOT -#define CONFIG_SYS_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ -#endif -#define CONFIG_SYS_CCSRBAR 0xfdf00000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ -#define CONFIG_SYS_FSL_DDR1 -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_SPD -#undef CONFIG_FSL_DDR_INTERACTIVE - -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */ -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ - -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) - -/* I2C addresses of SPD EEPROMs */ -#define SPD_EEPROM_ADDRESS 0x54 /* CTLR 0 DIMM 0 */ - -#undef CONFIG_CLOCKS_IN_MHZ - -/* local bus definitions */ -#define CONFIG_SYS_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ -#define CONFIG_SYS_OR2_PRELIM 0xfc006901 -#define CONFIG_SYS_LBC_LCRR 0x00030004 /* local bus freq */ -#define CONFIG_SYS_LBC_LBCR 0x00000000 -#define CONFIG_SYS_LBC_LSRT 0x20000000 -#define CONFIG_SYS_LBC_MRTPR 0x20000000 -#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723 -#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723 -#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723 -#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723 -#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723 - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ - -/* Serial Port */ -#define CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ -#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ - -#define CONFIG_BAUDRATE 38400 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER -#ifdef CONFIG_SYS_HUSH_PARSER -#endif - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 - -#if 0 -#define CONFIG_SYS_I2C_NOPROBES {0x00} /* Don't probe these addrs */ -#else -/* I did the 'if 0' so we could keep the syntax above if ever needed. */ -#undef CONFIG_SYS_I2C_NOPROBES -#endif - -/* RapdIO Map configuration, mapped 1:1. -*/ -#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 -#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE -#define CONFIG_SYS_RIO_MEM_SIZE 0x200000000 /* 512 M */ - -/* Standard 8560 PCI addressing, mapped 1:1. -*/ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_BASE 0xe2000000 -#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE -#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16 M */ - -#if defined(CONFIG_PCI) /* PCI Ethernet card */ - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP - -#if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xe0000000 - #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ -#endif - -#undef CONFIG_PCI_SCAN_SHOW -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_MII 1 /* MII PHY management */ - -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "TSEC1" - -#define TSEC1_PHY_ADDR 2 -#define TSEC2_PHY_ADDR 4 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT -#define CONFIG_ETHPRIME "TSEC0" - -#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ - -#define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */ -#undef CONFIG_ETHER_NONE /* define if ether on something else */ -#define CONFIG_ETHER_INDEX 2 /* which channel for ether */ - -#if (CONFIG_ETHER_INDEX == 2) - /* - * - Rx-CLK is CLK13 - * - Tx-CLK is CLK14 - * - Select bus for bd/buffers - * - Full duplex - */ - #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) - #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) - #define CONFIG_SYS_CPMFCR_RAMTYPE 0 -#if 0 - #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE) -#else - #define CONFIG_SYS_FCC_PSMR 0 -#endif - #define FETH2_RST 0x01 -#elif (CONFIG_ETHER_INDEX == 3) - /* need more definitions here for FE3 */ - #define FETH3_RST 0x80 -#endif /* CONFIG_ETHER_INDEX */ - -/* MDIO is done through the TSEC0 control. -*/ -#define CONFIG_MII /* MII PHY management */ -#undef CONFIG_BITBANGMII /* bit-bang MII PHY management */ - -#endif - -/* Environment */ -/* We use the top boot sector flash, so we have some 16K sectors for env - */ -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x60000) - #define CONFIG_ENV_SECT_SIZE 0x4000 /* 16K (one top sector) for env */ - #define CONFIG_ENV_SIZE 0x2000 -#else - #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ - #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400" -#define CONFIG_BOOTCOMMAND "bootm 0xff000000 0xff100000" -#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PING -#define CONFIG_CMD_I2C -#define CONFIG_CMD_REGINFO - -#if defined(CONFIG_SYS_RAMBOOT) - #undef CONFIG_CMD_SAVEENV - #undef CONFIG_CMD_LOADS -#else - #define CONFIG_CMD_ELF -#endif - -#if defined(CONFIG_PCI) - #define CONFIG_CMD_PCI -#endif - -#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_CMD_MII -#endif - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "GPPP=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/*Note: change below for your network setting!!! */ -#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) -#define CONFIG_HAS_ETH0 -#define CONFIG_ETHADDR 00:e0:0c:07:9b:8a -#define CONFIG_HAS_ETH1 -#define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b -#define CONFIG_HAS_ETH2 -#define CONFIG_ETH2ADDR 00:e0:0c:07:9b:8c -#endif - -#define CONFIG_SERVERIP 192.168.85.1 -#define CONFIG_IPADDR 192.168.85.60 -#define CONFIG_GATEWAYIP 192.168.85.1 -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_HOSTNAME STX_GP3 -#define CONFIG_ROOTPATH "/gppproot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_LOADADDR 0x1000000 - -#endif /* __CONFIG_H */ |