diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/ppmc8260.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/ppmc8260.h | 986 |
1 files changed, 986 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/ppmc8260.h b/qemu/roms/u-boot/include/configs/ppmc8260.h new file mode 100644 index 000000000..5dcd9cc0d --- /dev/null +++ b/qemu/roms/u-boot/include/configs/ppmc8260.h @@ -0,0 +1,986 @@ +/* + * (C) Copyright 2000 + * Murray Jensen <Murray.Jensen@cmst.csiro.au> + * + * (C) Copyright 2000 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger@sysgo.de> + * + * (C) Copyright 2001 + * Advent Networks, Inc. <http://www.adventnetworks.com> + * Jay Monkman <jtm@smoothsmoothie.com> + * + * Configuation settings for the WindRiver PPMC8260 board. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_SYS_TEXT_BASE 0xfe000000 + +/***************************************************************************** + * + * These settings must match the way _your_ board is set up + * + *****************************************************************************/ + +/* What is the oscillator's (UX2) frequency in Hz? */ +#define CONFIG_8260_CLKIN (66 * 1000 * 1000) + +/*----------------------------------------------------------------------- + * MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual + *----------------------------------------------------------------------- + * What should MODCK_H be? It is dependent on the oscillator + * frequency, MODCK[1-3], and desired CPM and core frequencies. + * Here are some example values (all frequencies are in MHz): + * + * MODCK_H MODCK[1-3] Osc CPM Core S2-6 S2-7 S2-8 + * ------- ---------- --- --- ---- ----- ----- ----- + * 0x2 0x2 33 133 133 Close Open Close + * 0x2 0x3 33 133 166 Close Open Open + * 0x2 0x4 33 133 200 Open Close Close + * 0x2 0x5 33 133 233 Open Close Open + * 0x2 0x6 33 133 266 Open Open Close + * + * 0x5 0x5 66 133 133 Open Close Open + * 0x5 0x6 66 133 166 Open Open Close + * 0x5 0x7 66 133 200 Open Open Open + * 0x6 0x0 66 133 233 Close Close Close + * 0x6 0x1 66 133 266 Close Close Open + * 0x6 0x2 66 133 300 Close Open Close + */ +#define CONFIG_SYS_PPMC_MODCK_H 0x05 + +/* Define this if you want to boot from 0x00000100. If you don't define + * this, you will need to program the bootloader to 0xfff00000, and + * get the hardware reset config words at 0xfe000000. The simplest + * way to do that is to program the bootloader at both addresses. + * It is suggested that you just let U-Boot live at 0x00000000. + */ +#define CONFIG_SYS_PPMC_BOOT_LOW 1 + +/* What should the base address of the main FLASH be and how big is + * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/ppmc8260/config.mk + * The main FLASH is whichever is connected to *CS0. U-Boot expects + * this to be the SIMM. + */ +#define CONFIG_SYS_FLASH0_BASE 0xFE000000 +#define CONFIG_SYS_FLASH0_SIZE 16 + +/* What should be the base address of the first SDRAM DIMM and how big is + * it (in Mbytes)? +*/ +#define CONFIG_SYS_SDRAM0_BASE 0x00000000 +#define CONFIG_SYS_SDRAM0_SIZE 128 + +/* What should be the base address of the second SDRAM DIMM and how big is + * it (in Mbytes)? +*/ +#define CONFIG_SYS_SDRAM1_BASE 0x08000000 +#define CONFIG_SYS_SDRAM1_SIZE 128 + +/* What should be the base address of the on board SDRAM and how big is + * it (in Mbytes)? +*/ +#define CONFIG_SYS_SDRAM2_BASE 0x38000000 +#define CONFIG_SYS_SDRAM2_SIZE 16 + +/* What should be the base address of the MAILBOX and how big is it + * (in Bytes) + * The eeprom lives at CONFIG_SYS_MAILBOX_BASE + 0x80000000 + */ +#define CONFIG_SYS_MAILBOX_BASE 0x32000000 +#define CONFIG_SYS_MAILBOX_SIZE 8192 + +/* What is the base address of the I/O select lines and how big is it + * (In Mbytes)? + */ + +#define CONFIG_SYS_IOSELECT_BASE 0xE0000000 +#define CONFIG_SYS_IOSELECT_SIZE 32 + + +/* What should be the base address of the LEDs and switch S0? + * If you don't want them enabled, don't define this. + */ +#define CONFIG_SYS_LED_BASE 0xF1000000 + +/* + * PPMC8260 with 256 16 MB DIMM: + * + * 0x0000 0000 Exception Vector code, 8k + * : + * 0x0000 1FFF + * 0x0000 2000 Free for Application Use + * : + * : + * + * : + * : + * 0x0FF5 FF30 Monitor Stack (Growing downward) + * Monitor Stack Buffer (0x80) + * 0x0FF5 FFB0 Board Info Data + * 0x0FF6 0000 Malloc Arena + * : CONFIG_ENV_SECT_SIZE, 256k + * : CONFIG_SYS_MALLOC_LEN, 128k + * 0x0FFC 0000 RAM Copy of Monitor Code + * : CONFIG_SYS_MONITOR_LEN, 256k + * 0x0FFF FFFF [End of RAM], CONFIG_SYS_SDRAM_SIZE - 1 + */ + + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere. + * The console can be on SMC1 or SMC2 + */ +#define CONFIG_CONS_ON_SMC 1 /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on neither */ +#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. + */ + +#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */ +#undef CONFIG_ETHER_NONE /* define if ethernet on neither */ +#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_BITBANGMII /* bit-bang MII PHY management */ +/* + * Port pins used for bit-banged MII communictions (if applicable). + */ +#define MDIO_PORT 2 /* Port C */ +#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ + (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) +#define MDC_DECLARE MDIO_DECLARE + +#define MDIO_ACTIVE (iop->pdir |= 0x00400000) +#define MDIO_TRISTATE (iop->pdir &= ~0x00400000) +#define MDIO_READ ((iop->pdat & 0x00400000) != 0) + +#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ + else iop->pdat &= ~0x00400000 + +#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ + else iop->pdat &= ~0x00200000 + +#define MIIDELAY udelay(1) + + +/* Define this to reserve an entire FLASH sector (256 KB) for + * environment variables. Otherwise, the environment will be + * put in the same sector as U-Boot, and changing variables + * will erase U-Boot temporarily + */ +#define CONFIG_ENV_IN_OWN_SECT 1 + +/* Define to allow the user to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +/* What should the console's baud rate be? */ +#define CONFIG_BAUDRATE 9600 + +/* Ethernet MAC address */ + +#define CONFIG_ETHADDR 00:a0:1e:90:2b:00 + +/* Define this to set the last octet of the ethernet address + * from the DS0-DS7 switch and light the leds with the result + * The DS0-DS7 switch and the leds are backwards with respect + * to each other. DS7 is on the board edge side of both the + * led strip and the DS0-DS7 switch. + */ +#define CONFIG_MISC_INIT_R + +/* Set to a positive value to delay for running BOOTCOMMAND */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#if 0 +/* Be selective on what keys can delay or stop the autoboot process + * To stop use: " " + */ +# define CONFIG_AUTOBOOT_KEYED +# define CONFIG_AUTOBOOT_PROMPT \ + "Autobooting in %d seconds, press \" \" to stop\n", bootdelay +# define CONFIG_AUTOBOOT_STOP_STR " " +# undef CONFIG_AUTOBOOT_DELAY_STR +# define DEBUG_BOOTKEYS 0 +#endif + +/* Define a command string that is automatically executed when no character + * is read on the console interface withing "Boot Delay" after reset. + */ +#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */ +#define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */ + +#ifdef CONFIG_BOOT_ROOT_INITRD +#define CONFIG_BOOTCOMMAND \ + "version;" \ + "echo;" \ + "bootp;" \ + "setenv bootargs root=/dev/ram0 rw " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ + "bootm" +#endif /* CONFIG_BOOT_ROOT_INITRD */ + +#ifdef CONFIG_BOOT_ROOT_NFS +#define CONFIG_BOOTCOMMAND \ + "version;" \ + "echo;" \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ + "bootm" +#endif /* CONFIG_BOOT_ROOT_NFS */ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_DNS + + +/* undef this to save memory */ +#define CONFIG_SYS_LONGHELP + +/* Monitor Command Prompt */ + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ELF +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_MEMTEST +#define CONFIG_CMD_MII +#define CONFIG_CMD_IMMAP + +#undef CONFIG_CMD_KGDB + + +/* Where do the internal registers live? */ +#define CONFIG_SYS_IMMR 0xf0000000 + +/***************************************************************************** + * + * You should not have to modify any of the following settings + * + *****************************************************************************/ + +#define CONFIG_PPMC8260 1 /* on an Wind River PPMC8260 Board */ +#define CONFIG_CPM2 1 /* Has a CPM2 */ + +/* + * Miscellaneous configurable options + */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) + +#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ + +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_LOAD_ADDR 0x140000 /* default load address */ + +#define CONFIG_SYS_MEMTEST_START 0x2000 /* memtest works from the end of */ + /* the exception vector table */ + /* to the end of the DRAM */ + /* less monitor and malloc area */ +#define CONFIG_SYS_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */ +#define CONFIG_SYS_MEM_END_USAGE ( CONFIG_SYS_MONITOR_LEN \ + + CONFIG_SYS_MALLOC_LEN \ + + CONFIG_ENV_SECT_SIZE \ + + CONFIG_SYS_STACK_USAGE ) + +#define CONFIG_SYS_MEMTEST_END ( CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 \ + - CONFIG_SYS_MEM_END_USAGE ) + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1) +/* + * Attention: This is board specific + * - RX clk is CLK11 + * - TX clk is CLK12 + */ +#define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 |\ + CMXSCR_TS1CS_CLK12) + +#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) +/* + * Attention: this is board-specific + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - Select bus for bd/buffers (see 28-13) + * - Enable Full Duplex in FSMR + */ +#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) +#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) +#define CONFIG_SYS_CPMFCR_RAMTYPE 0 +#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#endif /* CONFIG_ETHER_INDEX */ + +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE +#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE +#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SYS_SDRAM0_SIZE + CONFIG_SYS_SDRAM1_SIZE) + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + */ +#if defined(CONFIG_SYS_PPMC_BOOT_LOW) +# define CONFIG_SYS_PPMC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) +#else +# define CONFIG_SYS_PPMC_HRCW_BOOT_FLAGS (0) +#endif /* defined(CONFIG_SYS_PPMC_BOOT_LOW) */ + +/* get the HRCW ISB field from CONFIG_SYS_IMMR */ +#define CONFIG_SYS_PPMC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) | \ + ((CONFIG_SYS_IMMR & 0x01000000) >> 7) | \ + ((CONFIG_SYS_IMMR & 0x00100000) >> 4) ) + +#define CONFIG_SYS_HRCW_MASTER ( HRCW_EBM | \ + HRCW_BPS11 | \ + HRCW_L2CPC10 | \ + HRCW_DPPC00 | \ + CONFIG_SYS_PPMC_HRCW_IMMR | \ + HRCW_MMR00 | \ + HRCW_LBPC00 | \ + HRCW_APPC10 | \ + HRCW_CS10PC00 | \ + (CONFIG_SYS_PPMC_MODCK_H & HRCW_MODCK_H1111) | \ + CONFIG_SYS_PPMC_HRCW_BOOT_FLAGS ) + +/* no slaves */ +#define CONFIG_SYS_HRCW_SLAVE1 0 +#define CONFIG_SYS_HRCW_SLAVE2 0 +#define CONFIG_SYS_HRCW_SLAVE3 0 +#define CONFIG_SYS_HRCW_SLAVE4 0 +#define CONFIG_SYS_HRCW_SLAVE5 0 +#define CONFIG_SYS_HRCW_SLAVE6 0 +#define CONFIG_SYS_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent. + */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH0_BASE + +#ifndef CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE 0x0ff80000 +#endif + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 374 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ + +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ + + +#ifndef CONFIG_SYS_RAMBOOT + +# define CONFIG_ENV_IS_IN_FLASH 1 +# ifdef CONFIG_ENV_IN_OWN_SECT +# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) +# define CONFIG_ENV_SECT_SIZE 0x40000 +# else +# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE) +# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ +# define CONFIG_ENV_SECT_SIZE 0x40000 /* see README - env sect real size */ +# endif /* CONFIG_ENV_IN_OWN_SECT */ + +#else +# define CONFIG_ENV_IS_IN_FLASH 1 +# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000) +#define CONFIG_ENV_SIZE 0x1000 +# define CONFIG_ENV_SECT_SIZE 0x40000 +#endif /* CONFIG_SYS_RAMBOOT */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ + +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CONFIG_SYS_HID0_INIT (HID0_ICE |\ + HID0_DCE |\ + HID0_ICFI |\ + HID0_DCI |\ + HID0_IFEM |\ + HID0_ABE) + +#define CONFIG_SYS_HID0_FINAL (HID0_ICE |\ + HID0_IFEM |\ + HID0_ABE |\ + HID0_EMCP) +#define CONFIG_SYS_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_RMR 0 + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_BCR (BCR_EBM |\ + 0x30000000) + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + * Ref Section 4.3.2.6 page 4-31 + *----------------------------------------------------------------------- + */ + +#define CONFIG_SYS_SIUMCR (SIUMCR_ESE |\ + SIUMCR_DPPC00 |\ + SIUMCR_L2CPC10 |\ + SIUMCR_LBPC00 |\ + SIUMCR_APPC10 |\ + SIUMCR_CS10PC00 |\ + SIUMCR_BCTLC00 |\ + SIUMCR_MMR00) + + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\ + SYPCR_BMT |\ + SYPCR_PBME |\ + SYPCR_LBME |\ + SYPCR_SWRI |\ + SYPCR_SWP) + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\ + TMCNTSC_ALR |\ + TMCNTSC_TCF |\ + TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CONFIG_SYS_PISCR (PISCR_PS |\ + PISCR_PTF |\ + PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_SCCR 0 + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_RCCR 0 + +/* + * Initialize Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 32 bit FLASH (SIMM - 32MB) * + * 1 unused + * 2 60x SDRAM 64 bit SDRAM (DIMM - 128MB) + * 3 60x SDRAM 64 bit SDRAM (DIMM - 128MB) + * 4 Local SDRAM 32 bit SDRAM (on board - 16MB) + * 5 60x GPCM 8 bit Mailbox/EEPROM (8KB) + * 6 60x GPCM 8 bit FLASH (on board - 2MB) * + * 7 60x GPCM 8 bit LEDs, switches + * + * (*) This configuration requires the PPMC8260 be configured + * so that *CS0 goes to the FLASH SIMM, and *CS6 goes to + * the on board FLASH. In other words, JP24 should have + * pins 1 and 2 jumpered and pins 3 and 4 jumpered. + * + */ + +/*----------------------------------------------------------------------- + * BR0,BR1 - Base Register + * Ref: Section 10.3.1 on page 10-14 + * OR0,OR1 - Option Register + * Ref: Section 10.3.2 on page 10-18 + *----------------------------------------------------------------------- + */ + +/* Bank 0,1 - FLASH SIMM + * + * This expects the FLASH SIMM to be connected to *CS0 + * It consists of 4 AM29F080B parts. + * + * Note: For the 4 MB SIMM, *CS1 is unused. + */ + +/* BR0 is configured as follows: + * + * - Base address of 0xFE000000 + * - 32 bit port size + * - Data errors checking is disabled + * - Read and write access + * - GPCM 60x bus + * - Access are handled by the memory controller according to MSEL + * - Not used for atomic operations + * - No data pipelining is done + * - Valid + */ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +/* OR0 is configured as follows: + * + * - 32 MB + * - *BCTL0 is asserted upon access to the current memory bank + * - *CW / *WE are negated a quarter of a clock earlier + * - *CS is output at the same time as the address lines + * - Uses a clock cycle length of 5 + * - *PSDVAL is generated internally by the memory controller + * unless *GTA is asserted earlier externally. + * - Relaxed timing is generated by the GPCM for accesses + * initiated to this memory region. + * - One idle clock is inserted between a read access from the + * current bank and the next access. + */ +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_5_CLK |\ + ORxG_TRLX |\ + ORxG_EHTR) + +/*----------------------------------------------------------------------- + * BR2,BR3 - Base Register + * Ref: Section 10.3.1 on page 10-14 + * OR2,OR3 - Option Register + * Ref: Section 10.3.2 on page 10-16 + *----------------------------------------------------------------------- + */ + +/* + * Bank 2,3 - 128 MB SDRAM DIMM + */ + +/* With a 128 MB DIMM, the BR2 is configured as follows: + * + * - Base address of 0x00000000/0x08000000 + * - 64 bit port size (60x bus only) + * - Data errors checking is disabled + * - Read and write access + * - SDRAM 60x bus + * - Access are handled by the memory controller according to MSEL + * - Not used for atomic operations + * - No data pipelining is done + * - Valid + */ +#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +/* With a 128 MB DIMM, the OR2 is configured as follows: + * + * - 128 MB + * - 4 internal banks per device + * - Row start address bit is A8 with PSDMR[PBI] = 0 + * - 13 row address lines + * - Back-to-back page mode + * - Internal bank interleaving within save device enabled + */ + +#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A7 |\ + ORxS_NUMR_13) + +#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A7 |\ + ORxS_NUMR_13) + + +/*----------------------------------------------------------------------- + * PSDMR - 60x Bus SDRAM Mode Register + * Ref: Section 10.3.3 on page 10-21 + *----------------------------------------------------------------------- + */ + +/* With a 128 MB DIMM, the PSDMR is configured as follows: + * + * - Page Based Interleaving, + * - Refresh Enable, + * - Normal Operation + * - Address Multiplexing where A5 is output on A14 pin + * (A6 on A15, and so on), + * - use address pins A13-A15 as bank select, + * - A9 is output on SDA10 during an ACTIVATE command, + * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks, + * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command + * is 3 clocks, + * - earliest timing for READ/WRITE command after ACTIVATE command is + * 2 clocks, + * - earliest timing for PRECHARGE after last data was read is 1 clock, + * - earliest timing for PRECHARGE after last data was written is 1 clock, + * - External Address Multiplexing enabled + * - CAS Latency is 2. + */ +#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\ + PSDMR_SDAM_A14_IS_A5 |\ + PSDMR_BSMA_A13_A15 |\ + PSDMR_SDA10_PBI0_A9 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_3W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_EAMUX |\ + PSDMR_CL_2) + + +#define CONFIG_SYS_PSRT 0x0e +#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV32 + + +/*----------------------------------------------------------------------- + * BR4 - Base Register + * Ref: Section 10.3.1 on page 10-14 + * OR4 - Option Register + * Ref: Section 10.3.2 on page 10-16 + *----------------------------------------------------------------------- + */ + +/* + * Bank 4 - On board SDRAM + * + */ +/* With 16 MB of onboard SDRAM BR4 is configured as follows + * + * - Base address 0x38000000 + * - 32 bit port size + * - Data error checking disabled + * - Read/Write access + * - SDRAM local bus + * - Not used for atomic operations + * - No data pipelining is done + * - Valid + * + */ + +#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_SDRAM2_BASE & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_DECC_NONE |\ + BRx_MS_SDRAM_L |\ + BRx_V) + +/* + * With 16MB SDRAM, OR4 is configured as follows + * - 4 internal banks per device + * - Row start address bit is A10 with LSDMR[PBI] = 0 + * - 12 row address lines + * - Back-to-back page mode + * - Internal bank interleaving within save device enabled + */ + +#define CONFIG_SYS_OR4_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM2_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A10 |\ + ORxS_NUMR_12) + + +/*----------------------------------------------------------------------- + * LSDMR - Local Bus SDRAM Mode Register + * Ref: Section 10.3.4 on page 10-24 + *----------------------------------------------------------------------- + */ + +/* With a 16 MB onboard SDRAM, the LSDMR is configured as follows: + * + * - Page Based Interleaving, + * - Refresh Enable, + * - Normal Operation + * - Address Multiplexing where A5 is output on A13 pin + * (A6 on A15, and so on), + * - use address pins A15-A17 as bank select, + * - A11 is output on SDA10 during an ACTIVATE command, + * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks, + * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command + * is 2 clocks, + * - earliest timing for READ/WRITE command after ACTIVATE command is + * 2 clocks, + * - SDRAM burst length is 8 + * - earliest timing for PRECHARGE after last data was read is 1 clock, + * - earliest timing for PRECHARGE after last data was written is 1 clock, + * - External Address Multiplexing disabled + * - CAS Latency is 2. + */ +#define CONFIG_SYS_LSDMR (PSDMR_RFEN |\ + PSDMR_SDAM_A13_IS_A5 |\ + PSDMR_BSMA_A15_A17 |\ + PSDMR_SDA10_PBI0_A11 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_BL |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) + +#define CONFIG_SYS_LSRT 0x0e + +/*----------------------------------------------------------------------- + * BR5 - Base Register + * Ref: Section 10.3.1 on page 10-14 + * OR5 - Option Register + * Ref: Section 10.3.2 on page 10-16 + *----------------------------------------------------------------------- + */ + +/* + * Bank 5 EEProm and Mailbox + * + * The EEPROM and mailbox live on the same chip select. + * the eeprom is selected if the MSb of the address is set and the mailbox is + * selected if the MSb of the address is clear. + * + */ + +/* BR5 is configured as follows: + * + * - Base address of 0x32000000/0xF2000000 + * - 8 bit + * - Data error checking disabled + * - Read/Write access + * - GPCM 60x Bus + * - SDRAM local bus + * - No data pipelining is done + * - Valid + */ + +#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_MAILBOX_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_DECC_NONE |\ + BRx_MS_GPCM_P |\ + BRx_V) +/* OR5 is configured as follows + * - buffer control enabled + * - chip select negated normally + * - CS output 1/2 clock after address + * - 15 wait states + * - *PSDVAL is generated internally by the memory controller + * unless *GTA is asserted earlier externally. + * - Relaxed timing is generated by the GPCM for accesses + * initiated to this memory region. + * - One idle clock is inserted between a read access from the + * current bank and the next access. + */ + +#define CONFIG_SYS_OR5_PRELIM ((P2SZ_TO_AM(CONFIG_SYS_MAILBOX_SIZE) & ~0x80000000) |\ + ORxG_ACS_DIV2 |\ + ORxG_SCY_15_CLK |\ + ORxG_TRLX |\ + ORxG_EHTR) + +/*----------------------------------------------------------------------- + * BR6 - Base Register + * Ref: Section 10.3.1 on page 10-14 + * OR6 - Option Register + * Ref: Section 10.3.2 on page 10-18 + *----------------------------------------------------------------------- + */ + +/* Bank 6 - I/O select + * + */ + +/* BR6 is configured as follows: + * + * - Base address of 0xE0000000 + * - 16 bit port size + * - Data errors checking is disabled + * - Read and write access + * - GPCM 60x bus + * - Access are handled by the memory controller according to MSEL + * - Not used for atomic operations + * - No data pipelining is done + * - Valid + */ +#define CONFIG_SYS_BR6_PRELIM ((CONFIG_SYS_IOSELECT_BASE & BRx_BA_MSK) |\ + BRx_PS_16 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +/* OR6 is configured as follows + * - buffer control enabled + * - chip select negated normally + * - CS output 1/2 clock after address + * - 15 wait states + * - *PSDVAL is generated internally by the memory controller + * unless *GTA is asserted earlier externally. + * - Relaxed timing is generated by the GPCM for accesses + * initiated to this memory region. + * - One idle clock is inserted between a read access from the + * current bank and the next access. + */ + +#define CONFIG_SYS_OR6_PRELIM (MEG_TO_AM(CONFIG_SYS_IOSELECT_SIZE) |\ + ORxG_ACS_DIV2 |\ + ORxG_SCY_15_CLK |\ + ORxG_TRLX |\ + ORxG_EHTR) + + +/*----------------------------------------------------------------------- + * BR7 - Base Register + * Ref: Section 10.3.1 on page 10-14 + * OR7 - Option Register + * Ref: Section 10.3.2 on page 10-18 + *----------------------------------------------------------------------- + */ + +/* Bank 7 - LEDs and switches + * + * LEDs are at 0x00001 (write only) + * switches are at 0x00001 (read only) + */ +#ifdef CONFIG_SYS_LED_BASE + +/* BR7 is configured as follows: + * + * - Base address of 0xA0000000 + * - 8 bit port size + * - Data errors checking is disabled + * - Read and write access + * - GPCM 60x bus + * - Access are handled by the memory controller according to MSEL + * - Not used for atomic operations + * - No data pipelining is done + * - Valid + */ +#define CONFIG_SYS_BR7_PRELIM ((CONFIG_SYS_LED_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_DECC_NONE |\ + BRx_MS_GPCM_P |\ + BRx_V) + +/* OR7 is configured as follows: + * + * - 1 byte + * - *BCTL0 is asserted upon access to the current memory bank + * - *CW / *WE are negated a quarter of a clock earlier + * - *CS is output at the same time as the address lines + * - Uses a clock cycle length of 15 + * - *PSDVAL is generated internally by the memory controller + * unless *GTA is asserted earlier externally. + * - Relaxed timing is generated by the GPCM for accesses + * initiated to this memory region. + * - One idle clock is inserted between a read access from the + * current bank and the next access. + */ +#define CONFIG_SYS_OR7_PRELIM (ORxG_AM_MSK |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_15_CLK |\ + ORxG_TRLX |\ + ORxG_EHTR) +#endif /* CONFIG_SYS_LED_BASE */ +#endif /* __CONFIG_H */ |