diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/pdm360ng.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/pdm360ng.h | 481 |
1 files changed, 481 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/pdm360ng.h b/qemu/roms/u-boot/include/configs/pdm360ng.h new file mode 100644 index 000000000..553eb8f96 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/pdm360ng.h @@ -0,0 +1,481 @@ +/* + * (C) Copyright 2009-2010 + * Michael Weiß, ifm ecomatic gmbh, michael.weiss@ifm.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * pdm360ng board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_PDM360NG 1 + +/* + * Memory map for the PDM360NG board: + * + * 0x0000_0000 - 0x1FFF_FFFF DDR RAM (512 MB) + * 0x2000_0000 - 0x3FFF_FFFF reserved (DDR RAM (512 MB) + * 0x5000_0000 - 0x5001_FFFF SRAM (128 KB) + * 0x5004_0000 - 0x5005_FFFF MRAM (CS2) (128 KB) + * 0x8000_0000 - 0x803F_FFFF IMMR (4 MB) + * 0xF000_0000 - 0xF7FF_FFFF NOR FLASH (CS0) (128 MB) + * 0xF800_0000 - 0xFFFF_FFFF NOR FLASH (CS1) (128 MB) optional + */ + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 Family */ +#define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ + +#define CONFIG_SYS_TEXT_BASE 0xF0000000 + +/* Used for silent command in environment */ +#define CONFIG_SYS_DEVICE_NULLDEV +#define CONFIG_SILENT_CONSOLE + +/* Video */ +#define CONFIG_VIDEO + +#if defined(CONFIG_VIDEO) +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SPLASH_SCREEN +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_RLE8 +#endif + +#define CONFIG_SYS_MPC512X_CLKIN 33333333 /* in Hz */ + +#define CONFIG_MISC_INIT_R + +#define CONFIG_SYS_IMMR 0x80000000 +#define CONFIG_SYS_DIU_ADDR ((CONFIG_SYS_IMMR) + 0x2100) + +/* + * DDR Setup + */ + +/* DDR is system memory */ +#define CONFIG_SYS_DDR_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_MAX_RAM_SIZE 0x40000000 + +/* DDR pin mux and slew rate */ +#define CONFIG_SYS_IOCTRL_MUX_DDR 0x00000012 + +/* Manually set all parameters as there's no SPD etc. */ +/* + * DDR Controller Configuration for Micron DDR2 SDRAM MT47H128M8-3 + * + * SYS_CFG: + * [31:31] MDDRC Soft Reset: Diabled + * [30:30] DRAM CKE pin: Enabled + * [29:29] DRAM CLK: Enabled + * [28:28] Command Mode: Enabled (For initialization only) + * [27:25] DRAM Row Select: dram_row[15:0] = magenta_address[25:10] + * [24:21] DRAM Bank Select: dram_bank[1:0] = magenta_address[11:10] + * [20:19] Read Test: DON'T USE + * [18:18] Self Refresh: Enabled + * [17:17] 16bit Mode: Disabled + * [16:13] Read Delay: 3 + * [12:12] Half DQS Delay: Disabled + * [11:11] Quarter DQS Delay: Disabled + * [10:08] Write Delay: 2 + * [07:07] Early ODT: Disabled + * [06:06] On DIE Termination: Enabled + * [05:05] FIFO Overflow Clear: DON'T USE here + * [04:04] FIFO Underflow Clear: DON'T USE here + * [03:03] FIFO Overflow Pending: DON'T USE here + * [02:02] FIFO Underlfow Pending: DON'T USE here + * [01:01] FIFO Overlfow Enabled: Enabled + * [00:00] FIFO Underflow Enabled: Enabled + * TIME_CFG0 + * [31:16] DRAM Refresh Time: 0 CSB clocks + * [15:8] DRAM Command Time: 0 CSB clocks + * [07:00] DRAM Precharge Time: 0 CSB clocks + * TIME_CFG1 + * [31:26] DRAM tRFC: + * [25:21] DRAM tWR1: + * [20:17] DRAM tWRT1: + * [16:11] DRAM tDRR: + * [10:05] DRAM tRC: + * [04:00] DRAM tRAS: + * TIME_CFG2 + * [31:28] DRAM tRCD: + * [27:23] DRAM tFAW: + * [22:19] DRAM tRTW1: + * [18:15] DRAM tCCD: + * [14:10] DRAM tRTP: + * [09:05] DRAM tRP: + * [04:00] DRAM tRPA + */ +#define CONFIG_SYS_MDDRC_SYS_CFG 0xEA804A40 +#define CONFIG_SYS_MDDRC_TIME_CFG0 0x030C3D2E +#define CONFIG_SYS_MDDRC_TIME_CFG1 0x68EC1168 +#define CONFIG_SYS_MDDRC_TIME_CFG2 0x34310864 + +/* + * Alternative 1: small RAM (128 MB) configuration + */ +#define CONFIG_SYS_MDDRC_SYS_CFG_ALT1 0xE8604A40 +#define CONFIG_SYS_MDDRC_TIME_CFG0_ALT1 0x030C3D2E +#define CONFIG_SYS_MDDRC_TIME_CFG1_ALT1 0x3CEC1168 +#define CONFIG_SYS_MDDRC_TIME_CFG2_ALT1 0x33310863 + +#define CONFIG_SYS_MDDRC_SYS_CFG_EN 0xF0000000 + +#define CONFIG_SYS_DDRCMD_NOP 0x01380000 +#define CONFIG_SYS_DDRCMD_PCHG_ALL 0x01100400 +#define CONFIG_SYS_DDRCMD_EM2 0x01020000 /* EMR2 */ +#define CONFIG_SYS_DDRCMD_EM3 0x01030000 /* EMR3 */ +/* EMR with 150 ohm ODT todo: verify */ +#define CONFIG_SYS_DDRCMD_EN_DLL 0x01010040 +#define CONFIG_SYS_DDRCMD_RES_DLL 0x01000100 +#define CONFIG_SYS_DDRCMD_RFSH 0x01080000 +#define CONFIG_SYS_MICRON_INIT_DEV_OP 0x01000432 +/* EMR with 150 ohm ODT todo: verify */ +#define CONFIG_SYS_DDRCMD_OCD_DEFAULT 0x010107C0 +/* EMR new command with 150 ohm ODT todo: verify */ +#define CONFIG_SYS_DDRCMD_OCD_EXIT 0x01010440 + +/* DDR Priority Manager Configuration */ +#define CONFIG_SYS_MDDRCGRP_PM_CFG1 0x00077777 +#define CONFIG_SYS_MDDRCGRP_PM_CFG2 0x00000000 +#define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG 0x00000001 +#define CONFIG_SYS_MDDRCGRP_LUT0_MU 0xFFEEDDCC +#define CONFIG_SYS_MDDRCGRP_LUT0_ML 0xBBAAAAAA +#define CONFIG_SYS_MDDRCGRP_LUT1_MU 0x66666666 +#define CONFIG_SYS_MDDRCGRP_LUT1_ML 0x55555555 +#define CONFIG_SYS_MDDRCGRP_LUT2_MU 0x44444444 +#define CONFIG_SYS_MDDRCGRP_LUT2_ML 0x44444444 +#define CONFIG_SYS_MDDRCGRP_LUT3_MU 0x55555555 +#define CONFIG_SYS_MDDRCGRP_LUT3_ML 0x55555558 +#define CONFIG_SYS_MDDRCGRP_LUT4_MU 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT4_ML 0x11111122 +#define CONFIG_SYS_MDDRCGRP_LUT0_AU 0xaaaaaaaa +#define CONFIG_SYS_MDDRCGRP_LUT0_AL 0xaaaaaaaa +#define CONFIG_SYS_MDDRCGRP_LUT1_AU 0x66666666 +#define CONFIG_SYS_MDDRCGRP_LUT1_AL 0x66666666 +#define CONFIG_SYS_MDDRCGRP_LUT2_AU 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT2_AL 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT3_AU 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT3_AL 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT4_AU 0x11111111 +#define CONFIG_SYS_MDDRCGRP_LUT4_AL 0x11111111 + +/* + * NOR FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI /* use Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +#define CONFIG_SYS_FLASH_BASE 0xF0000000 /* start of FLASH-Bank0 */ +#define CONFIG_SYS_FLASH_SIZE 0x08000000 /* max size of a Bank */ +/* start of FLASH-Bank1 */ +#define CONFIG_SYS_FLASH1_BASE (CONFIG_SYS_FLASH_BASE + \ + CONFIG_SYS_FLASH_SIZE) +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per device */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_FLASH_BANKS_LIST \ + {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH1_BASE} + +#define CONFIG_SYS_SRAM_BASE 0x50000000 +#define CONFIG_SYS_SRAM_SIZE 0x00020000 /* 128 KB */ + +#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH1_BASE +#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_FLASH_SIZE + +/* ALE active low, data size 4 bytes */ +#define CONFIG_SYS_CS0_CFG 0x05059350 +/* ALE active low, data size 4 bytes */ +#define CONFIG_SYS_CS1_CFG 0x05059350 + +#define CONFIG_SYS_MRAM_BASE 0x50040000 +#define CONFIG_SYS_MRAM_SIZE 0x00020000 +#define CONFIG_SYS_CS2_START CONFIG_SYS_MRAM_BASE +#define CONFIG_SYS_CS2_SIZE CONFIG_SYS_MRAM_SIZE + +/* ALE active low, data size 4 bytes */ +#define CONFIG_SYS_CS2_CFG 0x05059110 + +/* alt. CS timing for CS0, CS1, CS2 */ +#define CONFIG_SYS_CS_ALETIMING 0x00000007 + +/* + * NAND FLASH + */ +#define CONFIG_CMD_NAND /* enable NAND support */ +#define CONFIG_NAND_MPC5121_NFC +#define CONFIG_SYS_NAND_BASE 0x40000000 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_SELECT_DEVICE /* driver supports mutipl. chips */ + +/* + * Configuration parameters for MPC5121 NAND driver + */ +#define CONFIG_FSL_NFC_WIDTH 1 +#define CONFIG_FSL_NFC_WRITE_SIZE 2048 +#define CONFIG_FSL_NFC_SPARE_SIZE 64 +#define CONFIG_FSL_NFC_CHIPS CONFIG_SYS_MAX_NAND_DEVICE + +/* + * Dynamic MTD partition support + */ +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_FLASH_CFI_MTD +#define MTDIDS_DEFAULT "nor0=f0000000.flash,nor1=f8000000.flash," \ + "nand0=MPC5121 NAND" + +/* + * Flash layout + */ +#define MTDPARTS_DEFAULT "mtdparts=f0000000.flash:512k(u-boot)," \ + "256k(environment1)," \ + "256k(environment2)," \ + "256k(splash-factory)," \ + "2m(FIT: recovery)," \ + "4608k(fs-recovery)," \ + "256k(splash-customer),"\ + "5m(FIT: kernel+dtb)," \ + "64m(rootfs squash)ro," \ + "51m(userfs ubi);" \ + "f8000000.flash:-(unused);" \ + "MPC5121 NAND:1024m(extended-userfs)" + +/* + * Override partitions in device tree using info + * in "mtdparts" environment variable + */ +#ifdef CONFIG_CMD_MTDPARTS +#define CONFIG_FDT_FIXUP_PARTITIONS +#endif + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* Start of monitor */ +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* 512 kB for monitor */ +#ifdef CONFIG_FSL_DIU_FB +#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* for malloc */ +#else +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) +#endif + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 6 /* console is on PSC6 */ +#if CONFIG_PSC_CONSOLE != 6 +#error CONFIG_PSC_CONSOLE must be 6 +#endif + +#define CONSOLE_FIFO_TX_SIZE FIFOC_PSC6_TX_SIZE +#define CONSOLE_FIFO_TX_ADDR FIFOC_PSC6_TX_ADDR +#define CONSOLE_FIFO_RX_SIZE FIFOC_PSC6_RX_SIZE +#define CONSOLE_FIFO_RX_ADDR FIFOC_PSC6_RX_ADDR + +/* + * Clocks in use + */ +#define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN | \ + CLOCK_SCCR1_LPC_EN | \ + CLOCK_SCCR1_NFC_EN | \ + CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) | \ + CLOCK_SCCR1_PSCFIFO_EN | \ + CLOCK_SCCR1_DDR_EN | \ + CLOCK_SCCR1_FEC_EN | \ + CLOCK_SCCR1_TPR_EN) + +#define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN | \ + CLOCK_SCCR2_SPDIF_EN | \ + CLOCK_SCCR2_DIU_EN | \ + CLOCK_SCCR2_I2C_EN) + +/* + * Used PSC UART devices + */ +#define CONFIG_SYS_PSC1 +#define CONFIG_SYS_PSC4 +#define CONFIG_SYS_PSC6 + +/* + * Co-processor communication parameters + */ +#define CONFIG_SYS_PDM360NG_COPROC_READ_DELAY 5000 +#define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE 38400 + +/* + * I2C + */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +/* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* + * IIM - IC Identification Module + */ +#undef CONFIG_FSL_IIM + +/* + * EEPROM configuration + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM addr */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* ST AT24C01 */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-Byte Write Mode */ + +/* + * MAC addr in EEPROM + */ +#define CONFIG_SYS_I2C_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_MAC_OFFSET 0x10 +/* + * Enabled only to delete "ethaddr" before testing + * "ethaddr" setting from EEPROM + */ +#define CONFIG_ENV_OVERWRITE + +/* + * Ethernet configuration + */ +#define CONFIG_MPC512x_FEC 1 +#define CONFIG_PHY_ADDR 0x1F +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_FEC_AN_TIMEOUT 1 +#define CONFIG_HAS_ETH0 + +/* + * Configure on-board RTC + */ +#define CONFIG_RTC_M41T62 /* use M41T00 rtc via i2c */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +/* This has to be a multiple of the Flash sector size */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x40000 /* one sector (256K) for env */ + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#undef CONFIG_CMD_FUSE + +#ifdef CONFIG_VIDEO +#define CONFIG_CMD_BMP +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ + +#ifdef CONFIG_CMD_KGDB + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +/* Max number of command args */ +#define CONFIG_SYS_MAXARGS 16 +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +/* Decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +/* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) + +/* Cache Configuration */ +#define CONFIG_SYS_DCACHE_SIZE 32768 +#define CONFIG_SYS_CACHELINE_SIZE 32 +#ifdef CONFIG_CMD_KGDB +/* log base 2 of the above value */ +#define CONFIG_SYS_CACHELINE_SHIFT 5 +#endif + +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | HID0_ICE) +#define CONFIG_SYS_HID2 HID2_HBE + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#endif + +/* POST support */ +#define CONFIG_POST (CONFIG_SYS_POST_COPROC) + +/* + * Environment Configuration + */ +#define CONFIG_TIMESTAMP + +#define CONFIG_HOSTNAME pdm360ng +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 400000 + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ + +#define CONFIG_PREBOOT "echo;" \ + "echo PDM360NG SAMPLE;" \ + "echo" + +#define CONFIG_BOOTCOMMAND "run env_cont" + +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES 1 +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE + +#define OF_CPU "PowerPC,5121@0" +#define OF_SOC_COMPAT "fsl,mpc5121-immr" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc@80000000/serial@11600" + +/* + * Include common options for all mpc5121 boards + */ +#include "mpc5121-common.h" + +#endif /* __CONFIG_H */ |