diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/omap3_beagle.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/omap3_beagle.h | 295 |
1 files changed, 0 insertions, 295 deletions
diff --git a/qemu/roms/u-boot/include/configs/omap3_beagle.h b/qemu/roms/u-boot/include/configs/omap3_beagle.h deleted file mode 100644 index fae0e6ffc..000000000 --- a/qemu/roms/u-boot/include/configs/omap3_beagle.h +++ /dev/null @@ -1,295 +0,0 @@ -/* - * (C) Copyright 2006-2008 - * Texas Instruments. - * Richard Woodruff <r-woodruff2@ti.com> - * Syed Mohammed Khasim <x0khasim@ti.com> - * - * Configuration settings for the TI OMAP3530 Beagle board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ - -/* - * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM - * 64 bytes before this address should be set aside for u-boot.img's - * header. That is 0x800FFFC0--0x80100000 should not be used for any - * other needs. We use this rather than the inherited defines from - * ti_armv7_common.h for backwards compatibility. - */ -#define CONFIG_SYS_TEXT_BASE 0x80100000 -#define CONFIG_SPL_BSS_START_ADDR 0x80000000 -#define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */ -#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 -#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 - -#include <configs/ti_omap3_common.h> - -/* - * Display CPU and Board information - */ -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_MISC_INIT_R - -#define CONFIG_REVISION_TAG 1 -#define CONFIG_ENV_OVERWRITE - -/* Status LED */ -#define CONFIG_STATUS_LED 1 -#define CONFIG_BOARD_SPECIFIC_LED 1 -#define STATUS_LED_BIT 0x01 -#define STATUS_LED_STATE STATUS_LED_ON -#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -#define STATUS_LED_BIT1 0x02 -#define STATUS_LED_STATE1 STATUS_LED_ON -#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) -#define STATUS_LED_BOOT STATUS_LED_BIT -#define STATUS_LED_GREEN STATUS_LED_BIT1 - -/* Enable Multi Bus support for I2C */ -#define CONFIG_I2C_MULTI_BUS 1 - -/* Probe all devices */ -#define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}} - -/* USB */ -#define CONFIG_MUSB_GADGET -#define CONFIG_USB_MUSB_OMAP2PLUS -#define CONFIG_MUSB_PIO_ONLY -#define CONFIG_USB_GADGET_DUALSPEED -#define CONFIG_TWL4030_USB 1 -#define CONFIG_USB_ETHER -#define CONFIG_USB_ETHER_RNDIS - -/* USB EHCI */ -#define CONFIG_CMD_USB -#define CONFIG_USB_EHCI - -#define CONFIG_USB_EHCI_OMAP -#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147 - -#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 -#define CONFIG_USB_HOST_ETHER -#define CONFIG_USB_ETHER_ASIX -#define CONFIG_USB_ETHER_MCS7830 -#define CONFIG_USB_ETHER_SMSC95XX - -/* GPIO banks */ -#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */ -#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ - -/* commands to include */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV - -#define CONFIG_CMD_CACHE - -#define MTDIDS_DEFAULT "nand0=nand" -#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\ - "1920k(u-boot),128k(u-boot-env),"\ - "4m(kernel),-(fs)" - -#define CONFIG_USB_STORAGE /* USB storage support */ -#define CONFIG_CMD_NAND /* NAND support */ -#define CONFIG_CMD_LED /* LED support */ -#define CONFIG_CMD_SETEXPR /* Evaluate expressions */ -#define CONFIG_CMD_GPIO /* Enable gpio command */ - -#define CONFIG_VIDEO_OMAP3 /* DSS Support */ - -/* - * TWL4030 - */ -#define CONFIG_TWL4030_LED 1 - -/* - * Board NAND Info. - */ -#define CONFIG_SYS_NAND_QUIET_TEST 1 -#define CONFIG_NAND_OMAP_GPMC -#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ - /* devices */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "loadaddr=0x80200000\0" \ - "rdaddr=0x81000000\0" \ - "fdt_high=0xffffffff\0" \ - "fdtaddr=0x80f80000\0" \ - "usbtty=cdc_acm\0" \ - "bootfile=uImage\0" \ - "ramdisk=ramdisk.gz\0" \ - "bootdir=/boot\0" \ - "bootpart=0:2\0" \ - "console=ttyO2,115200n8\0" \ - "mpurate=auto\0" \ - "buddy=none\0" \ - "optargs=\0" \ - "camera=none\0" \ - "vram=12M\0" \ - "dvimode=640x480MR-16@60\0" \ - "defaultdisplay=dvi\0" \ - "mmcdev=0\0" \ - "mmcroot=/dev/mmcblk0p2 rw\0" \ - "mmcrootfstype=ext3 rootwait\0" \ - "nandroot=ubi0:rootfs ubi.mtd=4\0" \ - "nandrootfstype=ubifs\0" \ - "ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \ - "ramrootfstype=ext2\0" \ - "mmcargs=setenv bootargs console=${console} " \ - "${optargs} " \ - "mpurate=${mpurate} " \ - "buddy=${buddy} "\ - "camera=${camera} "\ - "vram=${vram} " \ - "omapfb.mode=dvi:${dvimode} " \ - "omapdss.def_disp=${defaultdisplay} " \ - "root=${mmcroot} " \ - "rootfstype=${mmcrootfstype}\0" \ - "nandargs=setenv bootargs console=${console} " \ - "${optargs} " \ - "mpurate=${mpurate} " \ - "buddy=${buddy} "\ - "camera=${camera} "\ - "vram=${vram} " \ - "omapfb.mode=dvi:${dvimode} " \ - "omapdss.def_disp=${defaultdisplay} " \ - "root=${nandroot} " \ - "rootfstype=${nandrootfstype}\0" \ - "findfdt=" \ - "if test $beaglerev = AxBx; then " \ - "setenv fdtfile omap3-beagle.dtb; fi; " \ - "if test $beaglerev = Cx; then " \ - "setenv fdtfile omap3-beagle.dtb; fi; " \ - "if test $beaglerev = C4; then " \ - "setenv fdtfile omap3-beagle.dtb; fi; " \ - "if test $beaglerev = xMAB; then " \ - "setenv fdtfile omap3-beagle-xm.dtb; fi; " \ - "if test $beaglerev = xMC; then " \ - "setenv fdtfile omap3-beagle-xm.dtb; fi; " \ - "if test $fdtfile = undefined; then " \ - "echo WARNING: Could not determine device tree to use; fi; \0" \ - "bootenv=uEnv.txt\0" \ - "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ - "importbootenv=echo Importing environment from mmc ...; " \ - "env import -t $loadaddr $filesize\0" \ - "ramargs=setenv bootargs console=${console} " \ - "${optargs} " \ - "mpurate=${mpurate} " \ - "buddy=${buddy} "\ - "vram=${vram} " \ - "omapfb.mode=dvi:${dvimode} " \ - "omapdss.def_disp=${defaultdisplay} " \ - "root=${ramroot} " \ - "rootfstype=${ramrootfstype}\0" \ - "loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \ - "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \ - "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ - "mmcboot=echo Booting from mmc ...; " \ - "run mmcargs; " \ - "bootm ${loadaddr}\0" \ - "mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \ - "run mmcargs; " \ - "bootz ${loadaddr} - ${fdtaddr}\0" \ - "nandboot=echo Booting from nand ...; " \ - "run nandargs; " \ - "nand read ${loadaddr} 280000 400000; " \ - "bootm ${loadaddr}\0" \ - "ramboot=echo Booting from ramdisk ...; " \ - "run ramargs; " \ - "bootm ${loadaddr}\0" \ - "userbutton=if gpio input 173; then run userbutton_xm; " \ - "else run userbutton_nonxm; fi;\0" \ - "userbutton_xm=gpio input 4;\0" \ - "userbutton_nonxm=gpio input 7;\0" -/* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */ -#define CONFIG_BOOTCOMMAND \ - "run findfdt; " \ - "mmc dev ${mmcdev}; if mmc rescan; then " \ - "if run userbutton; then " \ - "setenv bootenv uEnv.txt;" \ - "else " \ - "setenv bootenv user.txt;" \ - "fi;" \ - "echo SD/MMC found on device ${mmcdev};" \ - "if run loadbootenv; then " \ - "echo Loaded environment from ${bootenv};" \ - "run importbootenv;" \ - "fi;" \ - "if test -n $uenvcmd; then " \ - "echo Running uenvcmd ...;" \ - "run uenvcmd;" \ - "fi;" \ - "if run loadimage; then " \ - "run mmcboot;" \ - "fi;" \ - "fi;" \ - "run nandboot;" \ - "setenv bootfile zImage;" \ - "if run loadimage; then " \ - "run loadfdt;" \ - "run mmcbootz; " \ - "fi; " \ - -/* - * OMAP3 has 12 GP timers, they can be driven by the system clock - * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). - * This rate is divided by a local divisor. - */ -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ - -/* **** PISMO SUPPORT *** */ - -/* Configure the PISMO */ -#define PISMO1_NAND_SIZE GPMC_SIZE_128M -#define PISMO1_ONEN_SIZE GPMC_SIZE_128M - -#if defined(CONFIG_CMD_NAND) -#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE -#endif - -/* Monitor at start of flash */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP - -#define CONFIG_ENV_IS_IN_NAND 1 -#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ -#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */ -#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ - -#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ -#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET -#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET - -#define CONFIG_OMAP3_SPI - -#define CONFIG_SYS_CACHELINE_SIZE 64 - -/* Defines for SPL */ -#define CONFIG_SPL_OMAP3_ID_NAND - -/* NAND boot config */ -#define CONFIG_SYS_NAND_5_ADDR_CYCLE -#define CONFIG_SYS_NAND_PAGE_COUNT 64 -#define CONFIG_SYS_NAND_PAGE_SIZE 2048 -#define CONFIG_SYS_NAND_OOBSIZE 64 -#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 -#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\ - 10, 11, 12, 13} -#define CONFIG_SYS_NAND_ECCSIZE 512 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 - -#endif /* __CONFIG_H */ |