diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/mpc8308_p1m.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/mpc8308_p1m.h | 532 |
1 files changed, 0 insertions, 532 deletions
diff --git a/qemu/roms/u-boot/include/configs/mpc8308_p1m.h b/qemu/roms/u-boot/include/configs/mpc8308_p1m.h deleted file mode 100644 index 4ae9afd4e..000000000 --- a/qemu/roms/u-boot/include/configs/mpc8308_p1m.h +++ /dev/null @@ -1,532 +0,0 @@ -/* - * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. - * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com - * - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ -#define CONFIG_MPC830x 1 /* MPC830x family */ -#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ -#define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFC000000 -#endif - -/* - * On-board devices - * - * TSECs - */ -#define CONFIG_TSEC1 -#define CONFIG_TSEC2 - -/* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 33333333 /* in Hz */ -#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN - -/* - * Hardware Reset Configuration Word - * if CLKIN is 66.66MHz, then - * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz - * We choose the A type silicon as default, so the core is 400Mhz. - */ -#define CONFIG_SYS_HRCW_LOW (\ - HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ - HRCWL_DDR_TO_SCB_CLK_2X1 |\ - HRCWL_SVCOD_DIV_2 |\ - HRCWL_CSB_TO_CLKIN_4X1 |\ - HRCWL_CORE_TO_CSB_3X1) -/* - * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits - * in 8308's HRCWH according to the manual, but original Freescale's - * code has them and I've expirienced some problems using the board - * with BDI3000 attached when I've tried to set these bits to zero - * (UART doesn't work after the 'reset run' command). - */ -#define CONFIG_SYS_HRCW_HIGH (\ - HRCWH_PCI_HOST |\ - HRCWH_PCI1_ARBITER_ENABLE |\ - HRCWH_CORE_ENABLE |\ - HRCWH_FROM_0X00000100 |\ - HRCWH_BOOTSEQ_DISABLE |\ - HRCWH_SW_WATCHDOG_DISABLE |\ - HRCWH_ROM_LOC_LOCAL_16BIT |\ - HRCWH_RL_EXT_LEGACY |\ - HRCWH_TSEC1M_IN_MII |\ - HRCWH_TSEC2M_IN_MII |\ - HRCWH_BIG_ENDIAN) - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRH (\ - SICRH_ESDHC_A_GPIO |\ - SICRH_ESDHC_B_GPIO |\ - SICRH_ESDHC_C_GTM |\ - SICRH_GPIO_A_TSEC2 |\ - SICRH_GPIO_B_TSEC2_TX_CLK |\ - SICRH_IEEE1588_A_GPIO |\ - SICRH_USB |\ - SICRH_GTM_GPIO |\ - SICRH_IEEE1588_B_GPIO |\ - SICRH_ETSEC2_CRS |\ - SICRH_GPIOSEL_1 |\ - SICRH_TMROBI_V3P3 |\ - SICRH_TSOBI1_V3P3 |\ - SICRH_TSOBI2_V3P3) /* 0xf577d100 */ -#define CONFIG_SYS_SICRL (\ - SICRL_SPI_PF0 |\ - SICRL_UART_PF0 |\ - SICRL_IRQ_PF0 |\ - SICRL_I2C2_PF0 |\ - SICRL_ETSEC1_TX_CLK) /* 0x00000000 */ - -#define CONFIG_SYS_GPIO1_PRELIM -/* GPIO Default input/output settings */ -#define CONFIG_SYS_GPIO1_DIR 0x7AAF8C00 -/* - * Default GPIO values: - * LED#1 enabled; WLAN enabled; Both COM LED on (orange) - */ -#define CONFIG_SYS_GPIO1_DAT 0x08008C00 - -/* - * IMMR new address - */ -#define CONFIG_SYS_IMMR 0xE0000000 - -/* - * SERDES - */ -#define CONFIG_FSL_SERDES -#define CONFIG_FSL_SERDES1 0xe3000 - -/* - * Arbiter Setup - */ -#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ -#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ -#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ - -/* - * DDR Setup - */ -#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 -#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ - | DDRCDR_PZ_LOZ \ - | DDRCDR_NZ_LOZ \ - | DDRCDR_ODT \ - | DDRCDR_Q_DRN) - /* 0x7b880001 */ -/* - * Manually set up DDR parameters - * consist of two chips HY5PS12621BFP-C4 from HYNIX - */ - -#define CONFIG_SYS_DDR_SIZE 128 /* MB */ - -#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ODT_RD_NEVER \ - | CSCONFIG_ODT_WR_ONLY_CURRENT \ - | CSCONFIG_ROW_BIT_13 \ - | CSCONFIG_COL_BIT_10) - /* 0x80010102 */ -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ - | (0 << TIMING_CFG0_WRT_SHIFT) \ - | (0 << TIMING_CFG0_RRT_SHIFT) \ - | (0 << TIMING_CFG0_WWT_SHIFT) \ - | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ - | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) - /* 0x00220802 */ -#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ - | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ - | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ - | (5 << TIMING_CFG1_CASLAT_SHIFT) \ - | (6 << TIMING_CFG1_REFREC_SHIFT) \ - | (2 << TIMING_CFG1_WRREC_SHIFT) \ - | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ - | (2 << TIMING_CFG1_WRTORD_SHIFT)) - /* 0x27256222 */ -#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ - | (4 << TIMING_CFG2_CPO_SHIFT) \ - | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ - | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ - | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ - | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ - | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) - /* 0x121048c5 */ -#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ - | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) - /* 0x03600100 */ -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ - | SDRAM_CFG_SDRAM_TYPE_DDR2 \ - | SDRAM_CFG_DBW_32) - /* 0x43080000 */ - -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ -#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ - | (0x0232 << SDRAM_MODE_SD_SHIFT)) - /* ODT 150ohm CL=3, AL=1 on SDRAM */ -#define CONFIG_SYS_DDR_MODE2 0x00000000 - -/* - * Memory test - */ -#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x07f00000 - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* - * Local Bus Configuration & Clock Setup - */ -#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP -#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 -#define CONFIG_SYS_LBC_LBCR 0x00040000 - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ -#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */ -#define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ - -/* Window base at flash base */ -#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ - | BR_PS_16 /* 16 bit port */ \ - | BR_MS_GPCM /* MSEL = GPCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ - | OR_UPM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_ACS_DIV2 \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_4 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET) - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 - -/* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024) -/* Flash Write Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024) - -/* - * SJA1000 CAN controller on Local Bus - */ -#define CONFIG_SYS_SJA1000_BASE 0xFBFF0000 -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_SJA1000_BASE \ - | BR_PS_8 /* 8 bit port size */ \ - | BR_MS_GPCM /* MSEL = GPCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ - | OR_GPCM_SCY_5 \ - | OR_GPCM_EHTR_SET) - /* 0xFFFF8052 */ - -#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE -#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) - -/* - * CPLD on Local Bus - */ -#define CONFIG_SYS_CPLD_BASE 0xFBFF8000 -#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_CPLD_BASE \ - | BR_PS_8 /* 8 bit port */ \ - | BR_MS_GPCM /* MSEL = GPCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB \ - | OR_GPCM_SCY_4 \ - | OR_GPCM_EHTR_SET) - /* 0xFFFF8042 */ - -#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE -#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* Pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCIE1_BASE 0xA0000000 -#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 -#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 -#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 -#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 - -/* enable PCIE clock */ -#define CONFIG_SYS_SCCR_PCIEXP1CM 1 - -#define CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_PCIE - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ -#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 - -/* - * TSEC - */ -#define CONFIG_TSEC_ENET /* TSEC ethernet support */ -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) - -/* - * TSEC ethernet configuration - */ -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_TSEC1_NAME "eTSEC0" -#define CONFIG_TSEC2_NAME "eTSEC1" -#define TSEC1_PHY_ADDR 1 -#define TSEC2_PHY_ADDR 2 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS 0 -#define TSEC2_FLAGS 0 - -/* Options are: eTSEC[0-1] */ -#define CONFIG_ETHPRIME "eTSEC0" - -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_I2C -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ - -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ - -/* - * Core HID Setup - */ -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ - HID0_ENABLE_INSTRUCTION_CACHE | \ - HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) -#define CONFIG_SYS_HID2 HID2_HBE - -/* - * MMU Setup - */ - -/* DDR: cache cacheable */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ - BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ - BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ - BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ - BATU_VP) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* FLASH: icache cacheable, but dcache-inhibit and guarded */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ - BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ - BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ - BATL_CACHEINHIBIT | \ - BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -/* Stack in dcache: cacheable, no memory coherence */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ - BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* - * Environment Configuration - */ - -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ - -#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs}" \ - " console=${consoledev},${baudrate}\0" \ - "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ - "addmisc=setenv bootargs ${bootargs}\0" \ - "kernel_addr=FC0A0000\0" \ - "fdt_addr=FC2A0000\0" \ - "ramdisk_addr=FC2C0000\0" \ - "u-boot=mpc8308_p1m/u-boot.bin\0" \ - "kernel_addr_r=1000000\0" \ - "fdt_addr_r=C00000\0" \ - "hostname=mpc8308_p1m\0" \ - "bootfile=mpc8308_p1m/uImage\0" \ - "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \ - "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ - "flash_self=run ramargs addip addtty addmtd addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ - "tftp ${fdt_addr_r} ${fdtfile};" \ - "run nfsargs addip addtty addmtd addmisc;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "bootcmd=run flash_self\0" \ - "load=tftp ${loadaddr} ${u-boot}\0" \ - "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ - " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ - " +${filesize};cp.b ${fileaddr} " \ - __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ - "upd=run load update\0" \ - -#endif /* __CONFIG_H */ |