diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/km/kmp204x-common.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/km/kmp204x-common.h | 465 |
1 files changed, 465 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/km/kmp204x-common.h b/qemu/roms/u-boot/include/configs/km/kmp204x-common.h new file mode 100644 index 000000000..efd96352e --- /dev/null +++ b/qemu/roms/u-boot/include/configs/km/kmp204x-common.h @@ -0,0 +1,465 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp <valentin.longchamp@keymile.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_KMP204X_H +#define _CONFIG_KMP204X_H + +#define CONFIG_PHYS_64BIT +#define CONFIG_PPC_P2041 + +#define CONFIG_SYS_TEXT_BASE 0xfff80000 + +#define CONFIG_KM_DEF_NETDEV "netdev=eth0\0" + +/* an additionnal option is required for UBI as subpage access is + * supported in u-boot */ +#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048" + +#define CONFIG_NAND_ECC_BCH + +/* common KM defines */ +#include "keymile-common.h" + +#define CONFIG_SYS_RAMBOOT +#define CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg +#define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ +#define CONFIG_MP /* support multiple processors */ + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_SYS_DPAA_RMAN /* RMan */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +/* Environment in SPI Flash */ +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 20000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB for u-boot */ +#define CONFIG_ENV_SIZE 0x004000 /* 16K env */ +#define CONFIG_ENV_SECT_SIZE 0x010000 +#define CONFIG_ENV_OFFSET_REDUND 0x110000 +#define CONFIG_ENV_TOTAL_SIZE 0x020000 + +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(unsigned long dummy); +#endif +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BACKSIDE_L2_CACHE +#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ + +#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE +#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ + CONFIG_RAMBOOT_TEXT_BASE) +#define CONFIG_SYS_L3_SIZE (1024 << 10) +#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) + +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_SYS_FSL_DDR3 +#define CONFIG_FSL_DDR_INTERACTIVE + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x54 +#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 + +/****************************************************************************** + * (PRAM usage) + * ... ------------------------------------------------------- + * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM + * ... |<------------------- pram -------------------------->| + * ... ------------------------------------------------------- + * @END_OF_RAM: + * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose + * @CONFIG_KM_PHRAM: address for /var + * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application) + * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM + */ + +/* size of rootfs in RAM */ +#define CONFIG_KM_ROOTFSSIZE 0x0 +/* pseudo-non volatile RAM [hex] */ +#define CONFIG_KM_PNVRAM 0x80000 +/* physical RAM MTD size [hex] */ +#define CONFIG_KM_PHRAM 0x100000 +/* reserved pram area at the end of memory [hex] + * u-boot reserves some memory for the MP boot page */ +#define CONFIG_KM_RESERVED_PRAM 0x1000 +/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable + * is not valid yet, which is the case for when u-boot copies itself to RAM */ +#define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10) + +#define CONFIG_KM_CRAMFS_ADDR 0x2000000 +#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */ +#define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */ + +/* + * Local Bus Definitions + */ + +/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */ +#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2) + +/* Nand Flash */ +#define CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_NAND_BASE 0xffa00000 +#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull + +#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +#define CONFIG_BCH + +/* NAND flash config */ +#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ + +#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \ + | OR_FCM_BCTLD /* LBCTL not ass */ \ + | OR_FCM_SCY_1 /* 1 clk wait cycle */ \ + | OR_FCM_RST /* 1 clk read setup */ \ + | OR_FCM_PGS /* Large page size */ \ + | OR_FCM_CST) /* 0.25 command setup */ + +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ + +/* QRIO FPGA */ +#define CONFIG_SYS_QRIO_BASE 0xfb000000 +#define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull + +#define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \ + | BR_PS_8 /* Port Size 8 bits */ \ + | BR_DECC_OFF /* no error corr */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ + +#define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \ + | OR_GPCM_BCTLD /* no LCTL assert */ \ + | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \ + | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \ + | OR_GPCM_TRLX /* relaxed tmgs */ \ + | OR_GPCM_EAD) /* extra bus clk cycles */ + +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */ + +/* bootcounter in QRIO */ +#define CONFIG_BOOTCOUNT_LIMIT +#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_QRIO_BASE + 0x20) + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ +#define CONFIG_MISC_INIT_F +#define CONFIG_MISC_INIT_R +#define CONFIG_LAST_STAGE_INIT + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) + +#define CONFIG_KM_CONSOLE_TTY "ttyS0" + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ + +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_INIT_BOARD +#define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */ +#define CONFIG_SYS_NUM_I2C_BUSES 3 +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \ + } +#ifndef __ASSEMBLY__ +void set_sda(int state); +void set_scl(int state); +int get_sda(void); +int get_scl(void); +#endif + +#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/ + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */ +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 20000000 +#define CONFIG_SF_DEFAULT_MODE 0 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ + +/* Qman/Bman */ +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 10 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 10 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull +#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME +/* Default address of microcode for the Linux Fman driver + * env is stored at 0x100000, sector size is 0x10000, x2 (redundant) + * ucode is stored after env, so we got 0x120000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_FMAN_FW_ADDR 0x120000 +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) + +#define CONFIG_FMAN_ENET +#define CONFIG_PHYLIB_10G +#define CONFIG_PHY_MARVELL /* there is a marvell phy */ + +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION + +/* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */ +#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11 +#define CONFIG_SYS_TBIPA_VALUE 8 +#define CONFIG_PHYLIB /* recommended PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC5" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * additionnal command line configuration. + */ +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#define CONFIG_CMD_ERRATA + +/* we don't need flash support */ +#define CONFIG_SYS_NO_FLASH +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#undef CONFIG_FLASH_CFI_MTD +#undef CONFIG_JFFS2_CMDLINE + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#endif + +#define __USB_PHY_TYPE utmi + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE +#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ +#define CONFIG_KM_DEF_ENV "km-common=empty\0" +#endif + +#ifndef MTDIDS_DEFAULT +# define MTDIDS_DEFAULT "nand0=fsl_elbc_nand" +#endif /* MTDIDS_DEFAULT */ + +#ifndef MTDPARTS_DEFAULT +# define MTDPARTS_DEFAULT "mtdparts=" \ + "fsl_elbc_nand:" \ + "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" +#endif /* MTDPARTS_DEFAULT */ + +/* architecture specific default bootargs */ +#define CONFIG_KM_DEF_BOOT_ARGS_CPU "" + +/* FIXME: FDT_ADDR is unspecified */ +#define CONFIG_KM_DEF_ENV_CPU \ + "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ + "cramfsloadfdt=" \ + "cramfsload ${fdt_addr_r} " \ + "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ + "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \ + "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0" \ + "update=" \ + "sf probe 0;sf erase 0 +${filesize};" \ + "sf write ${load_addr_r} 0 ${filesize};\0" \ + "set_fdthigh=true\0" \ + "" + +#define CONFIG_HW_ENV_SETTINGS \ + "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \ + "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ + "usb_dr_mode=host\0" + +#define CONFIG_KM_NEW_ENV \ + "newenv=sf probe 0;" \ + "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \ + __stringify(CONFIG_ENV_TOTAL_SIZE)"\0" + +/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */ +#ifndef CONFIG_KM_DEF_ARCH +#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_DEF_ENV \ + CONFIG_KM_DEF_ARCH \ + CONFIG_KM_NEW_ENV \ + CONFIG_HW_ENV_SETTINGS \ + "EEprom_ivm=pca9547:70:9\0" \ + "" + +#endif /* _CONFIG_KMP204X_H */ |