diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/inka4x0.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/inka4x0.h | 419 |
1 files changed, 0 insertions, 419 deletions
diff --git a/qemu/roms/u-boot/include/configs/inka4x0.h b/qemu/roms/u-boot/include/configs/inka4x0.h deleted file mode 100644 index f321975c4..000000000 --- a/qemu/roms/u-boot/include/configs/inka4x0.h +++ /dev/null @@ -1,419 +0,0 @@ -/* - * (C) Copyright 2009 - * Detlev Zundel, DENX Software Engineering, dzu@denx.de. - * - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_INKA4X0 1 /* INKA4x0 board */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFFE00000 boot low - * 0x00100000 boot from RAM (for testing only) - */ -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFE00000 /* Standard: boot low */ -#endif -#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc5xxx/u-boot-customlayout.lds" - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_SYS_XLB_PIPELINING 1 - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_IDE -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_SNTP -#define CONFIG_CMD_USB - -#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ - -#if (CONFIG_SYS_TEXT_BASE == 0xFFE00000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_ETHADDR 00:a0:a4:03:00:00 -#define CONFIG_OVERWRITE_ETHADDR_ONCE - -#define CONFIG_IPADDR 192.168.100.2 -#define CONFIG_SERVERIP 192.168.100.1 -#define CONFIG_NETMASK 255.255.255.0 -#define HOSTNAME inka4x0 -#define CONFIG_BOOTFILE "/tftpboot/inka4x0/uImage" -#define CONFIG_ROOTPATH "/opt/eldk/ppc_6xx" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addcons=setenv bootargs ${bootargs} " \ - "console=ttyS0,${baudrate}\0" \ - "flash_nfs=run nfsargs addip addcons;" \ - "bootm ${kernel_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};" \ - "run nfsargs addip addcons;bootm\0" \ - "enable_disp=mw.l 100000 04000000 1;" \ - "cp.l 100000 f0000b20 1;" \ - "cp.l 100000 f0000b28 1\0" \ - "ideargs=setenv bootargs root=/dev/hda1 rw\0" \ - "ide_boot=ext2load ide 0:1 200000 uImage;" \ - "run ideargs addip addcons enable_disp;bootm\0" \ - "brightness=255\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run ide_boot" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 -#define CONFIG_SYS_FLASH_BASE 0xffe00000 -#define CONFIG_SYS_FLASH_SIZE 0x00200000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000) -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x2000 -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* - * SDRAM controller configuration - */ -#undef CONFIG_SDR_MT48LC16M16A2 -#undef CONFIG_DDR_MT46V16M16 -#undef CONFIG_DDR_MT46V32M16 -#undef CONFIG_DDR_HYB25D512160BF -#define CONFIG_DDR_K4H511638C - -/* Use ON-Chip SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM - -/* preserve space for the post_word at end of on-chip SRAM */ -#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4) - -#ifdef CONFIG_POST -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE -#else -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE -#endif - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -/* - * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb - */ -/* #define CONFIG_MPC5xxx_FEC_MII10 */ -#define CONFIG_PHY_ADDR 0x00 -#define CONFIG_MII - -/* - * GPIO configuration - * - * use CS1 as gpio_wkup_6 output - * Bit 0 (mask: 0x80000000): 0 - * use ALT CAN position: Bits 2-3 (mask: 0x30000000): - * 00 -> No Alternatives, I2C1 is used for onboard EEPROM - * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard - * EEPROM - * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 - * use PSC2 as UART: Bits 24-27 (mask: 0x00000070): 0100 - * use PSC3 as UART: Bits 20-23 (mask: 0x00000700): 0100 - * use PSC6 as UART: Bits 9-11 (mask: 0x00700000): 0101 - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x01501444 - -/* - * RTC configuration - */ -#define CONFIG_RTC_RTC4543 1 /* use external RTC */ - -/* - * Software (bit-bang) three wire serial configuration - * - * Note that we need the ifdefs because otherwise compilation of - * mkimage.c fails. - */ -#define CONFIG_SOFT_TWS 1 - -#ifdef TWS_IMPLEMENTATION -#include <mpc5xxx.h> -#include <asm/io.h> - -#define TWS_CE MPC5XXX_GPIO_WKUP_PSC1_4 /* GPIO_WKUP_0 */ -#define TWS_WR MPC5XXX_GPIO_WKUP_PSC2_4 /* GPIO_WKUP_1 */ -#define TWS_DATA MPC5XXX_GPIO_SINT_PSC3_4 /* GPIO_SINT_0 */ -#define TWS_CLK MPC5XXX_GPIO_SINT_PSC3_5 /* GPIO_SINT_1 */ - -static inline void tws_ce(unsigned bit) -{ - struct mpc5xxx_wu_gpio *wu_gpio = - (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO; - if (bit) - setbits_8(&wu_gpio->dvo, TWS_CE); - else - clrbits_8(&wu_gpio->dvo, TWS_CE); -} - -static inline void tws_wr(unsigned bit) -{ - struct mpc5xxx_wu_gpio *wu_gpio = - (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO; - if (bit) - setbits_8(&wu_gpio->dvo, TWS_WR); - else - clrbits_8(&wu_gpio->dvo, TWS_WR); -} - -static inline void tws_clk(unsigned bit) -{ - struct mpc5xxx_gpio *gpio = - (struct mpc5xxx_gpio *)MPC5XXX_GPIO; - if (bit) - setbits_8(&gpio->sint_dvo, TWS_CLK); - else - clrbits_8(&gpio->sint_dvo, TWS_CLK); -} - -static inline void tws_data(unsigned bit) -{ - struct mpc5xxx_gpio *gpio = - (struct mpc5xxx_gpio *)MPC5XXX_GPIO; - if (bit) - setbits_8(&gpio->sint_dvo, TWS_DATA); - else - clrbits_8(&gpio->sint_dvo, TWS_DATA); -} - -static inline unsigned tws_data_read(void) -{ - struct mpc5xxx_gpio *gpio = - (struct mpc5xxx_gpio *)MPC5XXX_GPIO; - return !!(in_8(&gpio->sint_ival) & TWS_DATA); -} - -static inline void tws_data_config_output(unsigned output) -{ - struct mpc5xxx_gpio *gpio = - (struct mpc5xxx_gpio *)MPC5XXX_GPIO; - if (output) - setbits_8(&gpio->sint_ddr, TWS_DATA); - else - clrbits_8(&gpio->sint_ddr, TWS_DATA); -} -#endif /* TWS_IMPLEMENTATION */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* Enable an alternate, more extensive memory test */ -#define CONFIG_SYS_ALT_MEMTEST - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Enable loopw command. - */ -#define CONFIG_LOOPW - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00087800 /* for pci_clk = 66 MHz */ -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -/* 32Mbit SRAM @0x30000000 */ -#define CONFIG_SYS_CS1_START 0x30000000 -#define CONFIG_SYS_CS1_SIZE 0x00400000 -#define CONFIG_SYS_CS1_CFG 0x31800 /* for pci_clk = 33 MHz */ - -/* 2 quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */ -#define CONFIG_SYS_CS2_START 0x80000000 -#define CONFIG_SYS_CS2_SIZE 0x0001000 -#define CONFIG_SYS_CS2_CFG 0x21800 /* for pci_clk = 33 MHz */ - -/* GPIO in @0x30400000 */ -#define CONFIG_SYS_CS3_START 0x30400000 -#define CONFIG_SYS_CS3_SIZE 0x00100000 -#define CONFIG_SYS_CS3_CFG 0x31800 /* for pci_clk = 33 MHz */ - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_OHCI -#define CONFIG_USB_CLOCK 0x00015555 -#define CONFIG_USB_CONFIG 0x00001000 -#define CONFIG_USB_STORAGE - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0060 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x005C /* Offset for alternate registers */ -#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ - -#define CONFIG_ATAPI 1 - -#define CONFIG_SYS_BRIGHTNESS 0xFF /* LCD Default Brightness (255 = off) */ - -#endif /* __CONFIG_H */ |