diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/ids8313.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/ids8313.h | 586 |
1 files changed, 586 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/ids8313.h b/qemu/roms/u-boot/include/configs/ids8313.h new file mode 100644 index 000000000..c1b3b633e --- /dev/null +++ b/qemu/roms/u-boot/include/configs/ids8313.h @@ -0,0 +1,586 @@ +/* + * (C) Copyright 2013 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * Based on: + * Copyright (c) 2011 IDS GmbH, Germany + * Sergej Stepanov <ste@ids.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_MPC831x +#define CONFIG_MPC8313 +#define CONFIG_IDS8313 + +#define CONFIG_FSL_ELBC + +#define CONFIG_MISC_INIT_R + +#define CONFIG_AUTOBOOT_KEYED +#define CONFIG_AUTOBOOT_PROMPT \ + "\nEnter password - autoboot in %d seconds...\n", CONFIG_BOOTDELAY +#define CONFIG_AUTOBOOT_DELAY_STR "ids" +#define CONFIG_BOOT_RETRY_TIME 900 +#define CONFIG_BOOT_RETRY_MIN 30 +#define CONFIG_BOOTDELAY 1 +#define CONFIG_RESET_TO_RETRY + +#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN + +#define CONFIG_SYS_IMMR 0xF0000000 + +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ + +/* + * Hardware Reset Configuration Word + * if CLKIN is 66.000MHz, then + * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz + */ +#define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_CSB_TO_CLKIN_2X1 |\ + HRCWL_CORE_TO_CSB_2X1) + +#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0XFFF00100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_8BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_MII |\ + HRCWH_TSEC2M_IN_MII |\ + HRCWH_BIG_ENDIAN) + +#define CONFIG_SYS_SICRH 0x00000000 +#define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D) + +#define CONFIG_HWCONFIG + +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK |\ + HID0_ENABLE_INSTRUCTION_CACHE |\ + HID0_DISABLE_DYNAMIC_POWER_MANAGMENT) + +#define CONFIG_SYS_HID2 (HID2_HBE | 0x00020000) + +/* + * Definitions for initial stack pointer and data area (in DCACHE ) + */ +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ + - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* + * Local Bus LCRR and LBCR regs + */ +#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1 +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 +#define CONFIG_SYS_LBC_LBCR (0x00040000 |\ + (0xFF << LBCR_BMT_SHIFT) |\ + 0xF) + +#define CONFIG_SYS_LBC_MRTPR 0x20000000 + +/* + * Internal Definitions + */ +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE + +/* + * Manually set up DDR parameters, + * as this board has not the SPD connected to I2C. + */ +#define CONFIG_SYS_DDR_SIZE 256 /* MB */ +#define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN |\ + 0x00010000 |\ + CSCONFIG_ROW_BIT_13 |\ + CSCONFIG_COL_BIT_10) + +#define CONFIG_SYS_DDR_CONFIG_256 (CONFIG_SYS_DDR_CONFIG | \ + CSCONFIG_BANK_BIT_3) + +#define CONFIG_SYS_DDR_TIMING_3 (1 << 16) /* ext refrec */ +#define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\ + (3 << TIMING_CFG0_WRT_SHIFT) |\ + (3 << TIMING_CFG0_RRT_SHIFT) |\ + (3 << TIMING_CFG0_WWT_SHIFT) |\ + (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\ + (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\ + (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (2 << TIMING_CFG0_MRS_CYC_SHIFT)) +#define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\ + (12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\ + (4 << TIMING_CFG1_ACTTORW_SHIFT) |\ + (7 << TIMING_CFG1_CASLAT_SHIFT) |\ + (4 << TIMING_CFG1_REFREC_SHIFT) |\ + (4 << TIMING_CFG1_WRREC_SHIFT) |\ + (2 << TIMING_CFG1_ACTTOACT_SHIFT) |\ + (2 << TIMING_CFG1_WRTORD_SHIFT)) +#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\ + (5 << TIMING_CFG2_CPO_SHIFT) |\ + (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\ + (0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\ + (1 << TIMING_CFG2_CKE_PLS_SHIFT) |\ + (6 << TIMING_CFG2_FOUR_ACT_SHIFT)) + +#define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\ + (0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + +#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN |\ + SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\ + SDRAM_CFG_DBW_32 |\ + SDRAM_CFG_SDRAM_TYPE_DDR2) + +#define CONFIG_SYS_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\ + (0x0242 << SDRAM_MODE_SD_SHIFT)) +#define CONFIG_SYS_DDR_MODE_2 0x00000000 +#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075 +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\ + DDRCDR_PZ_NOMZ |\ + DDRCDR_NZ_NOMZ |\ + DDRCDR_ODT |\ + DDRCDR_M_ODR |\ + DDRCDR_Q_DRN) + +/* + * on-board devices + */ +#define CONFIG_TSEC1 +#define CONFIG_TSEC2 +#define CONFIG_TSEC_ENET +#define CONFIG_NET_MULTI +#define CONFIG_HARD_SPI +#define CONFIG_HARD_I2C + +/* + * NOR FLASH setup + */ +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT +#define CONFIG_FLASH_SHOW_PROGRESS 50 +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +#define CONFIG_SYS_FLASH_BASE 0xFF800000 +#define CONFIG_SYS_FLASH_SIZE 8 +#define CONFIG_SYS_FLASH_PROTECTION + +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 + +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\ + BR_PS_8 |\ + BR_MS_GPCM |\ + BR_V) + +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ + OR_GPCM_SCY_10 |\ + OR_GPCM_EHTR |\ + OR_GPCM_TRLX |\ + OR_GPCM_CSNT |\ + OR_GPCM_EAD) +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 128 + +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 + +/* + * NAND FLASH setup + */ +#define CONFIG_SYS_NAND_BASE 0xE1000000 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_MAX_CHIPS 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_NAND_PAGE_SIZE (2048) +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) +#define NAND_CACHE_PAGES 64 + +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E +#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM +#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM + +#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_NAND_BASE) |\ + (2<<BR_DECC_SHIFT) |\ + BR_PS_8 |\ + BR_MS_FCM |\ + BR_V) + +#define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 |\ + OR_FCM_PGS |\ + OR_FCM_CSCT |\ + OR_FCM_CST |\ + OR_FCM_CHT |\ + OR_FCM_SCY_4 |\ + OR_FCM_TRLX |\ + OR_FCM_EHTR |\ + OR_FCM_RST) + +/* + * MRAM setup + */ +#define CONFIG_SYS_MRAM_BASE 0xE2000000 +#define CONFIG_SYS_MRAM_SIZE 0x20000 /* 128 Kb */ +#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_MRAM_BASE +#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* 128 Kb */ + +#define CONFIG_SYS_OR_TIMING_MRAM + +#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_MRAM_BASE |\ + BR_PS_8 |\ + BR_MS_GPCM |\ + BR_V) + +#define CONFIG_SYS_OR2_PRELIM 0xFFFE0C74 + +/* + * CPLD setup + */ +#define CONFIG_SYS_CPLD_BASE 0xE3000000 +#define CONFIG_SYS_CPLD_SIZE 0x8000 +#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_CPLD_BASE +#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E + +#define CONFIG_SYS_OR_TIMING_MRAM + +#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CPLD_BASE |\ + BR_PS_8 |\ + BR_MS_GPCM |\ + BR_V) + +#define CONFIG_SYS_OR3_PRELIM 0xFFFF8814 + +/* + * HW-Watchdog + */ +#define CONFIG_WATCHDOG 1 +#define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF + +/* + * I2C setup + */ +#define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 +#define CONFIG_RTC_PCF8563 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 + +/* + * SPI setup + */ +#ifdef CONFIG_HARD_SPI +#define CONFIG_MPC8XXX_SPI +#define CONFIG_CMD_SPI +#define CONFIG_SYS_GPIO1_PRELIM +#define CONFIG_SYS_GPIO1_DIR 0x00000001 +#define CONFIG_SYS_GPIO1_DAT 0x00000001 +#endif + +/* + * Ethernet setup + */ +#ifdef CONFIG_TSEC1 +#define CONFIG_HAS_ETH0 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define TSEC1_PHY_ADDR 0x1 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC1_PHYIDX 0 +#endif + +#ifdef CONFIG_TSEC2 +#define CONFIG_HAS_ETH1 +#define CONFIG_TSEC2_NAME "TSEC1" +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define TSEC2_PHY_ADDR 0x3 +#define TSEC2_FLAGS TSEC_GIGABIT +#define TSEC2_PHYIDX 0 +#endif +#define CONFIG_ETHPRIME "TSEC1" + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) +#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2) + +#define CONFIG_HAS_FSL_DR_USB +#define CONFIG_SYS_SCCR_USBDRCM 3 + +/* + * BAT's + */ +#define CONFIG_HIGH_BATS + +/* DDR @ 0x00000000 */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE |\ + BATL_PP_10) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE |\ + BATU_BL_256M |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U + +/* Initial RAM @ 0xFD000000 */ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR |\ + BATL_PP_10 |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR |\ + BATU_BL_256K |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U + +/* FLASH @ 0xFF800000 */ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE |\ + BATL_PP_10 |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE |\ + BATU_BL_8M |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE |\ + BATL_PP_10 |\ + BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U + +#define CONFIG_SYS_IBAT3L (0) +#define CONFIG_SYS_IBAT3U (0) +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U + +#define CONFIG_SYS_IBAT4L (0) +#define CONFIG_SYS_IBAT4U (0) +#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U + +/* IMMRBAR @ 0xF0000000 */ +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR |\ + BATL_PP_10 |\ + BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR |\ + BATU_BL_128M |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U + +/* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */ +#define CONFIG_SYS_IBAT6L (0xE0000000 |\ + BATL_PP_10 |\ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT6U (0xE0000000 |\ + BATU_BL_256M |\ + BATU_VS |\ + BATU_VP) +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U + +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U + +/* + * U-Boot environment setup + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_NFS +#define CONFIG_CMD_NAND +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_MII +#define CONFIG_CMD_DATE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_CMD_EDITENV +#define CONFIG_CMD_JFFS2 +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) +#define CONFIG_SYS_MALLOC_LEN (8 * 1024 * 1024) + +/* + * Environment Configuration + */ +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ + + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + + +#define CONFIG_NETDEV eth1 +#define CONFIG_HOSTNAME ids8313 +#define CONFIG_ROOTPATH "/opt/eldk-4.2/ppc_6xx" +#define CONFIG_BOOTFILE "ids8313/uImage" +#define CONFIG_UBOOTPATH "ids8313/u-boot.bin" +#define CONFIG_FDTFILE "ids8313/ids8313.dtb" +#define CONFIG_LOADADDR 0x400000 +#define CONFIG_CMD_ENV_FLAGS +#define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo" + +#define CONFIG_BAUDRATE 115200 + +/* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_SYS_CBSIZE 1024 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ + + sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#define CONFIG_SYS_MEMTEST_START 0x00001000 +#define CONFIG_SYS_MEMTEST_END 0x00C00000 + +#define CONFIG_SYS_LOAD_ADDR 0x100000 +#define CONFIG_MII +#define CONFIG_LOADS_ECHO +#define CONFIG_TIMESTAMP +#define CONFIG_PREBOOT "echo;" \ + "echo Type \\\"run nfsboot\\\" " \ + "to mount root filesystem over NFS;echo" +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND "run boot_cramfs" +#undef CONFIG_SYS_LOADS_BAUD_CHANGE + +#define CONFIG_JFFS2_NAND +#define CONFIG_JFFS2_DEV "0" + +/* mtdparts command line support */ +#define CONFIG_CMD_MTDPARTS +#define CONFIG_FLASH_CFI_MTD +#define CONFIG_MTD_DEVICE +#define MTDIDS_DEFAULT "nor0=ff800000.flash,nand0=e1000000.flash" +#define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:7m(dum)," \ + "768k(BOOT-BIN)," \ + "128k(BOOT-ENV),128k(BOOT-REDENV);" \ + "e1000000.flash:-(ubi)" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=" __stringify(CONFIG_NETDEV) "\0" \ + "ethprime=TSEC1\0" \ + "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ + "tftpflash=tftpboot ${loadaddr} ${uboot}; " \ + "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +${filesize}; " \ + "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +${filesize}; " \ + "cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ + " ${filesize}; " \ + "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ + " +${filesize}; " \ + "cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ + " ${filesize}\0" \ + "console=ttyS0\0" \ + "fdtaddr=0x780000\0" \ + "kernel_addr=ff800000\0" \ + "fdtfile=" __stringify(CONFIG_FDTFILE) "\0" \ + "setbootargs=setenv bootargs " \ + "root=${rootdev} rw console=${console}," \ + "${baudrate} ${othbootargs}\0" \ + "setipargs=setenv bootargs root=${rootdev} rw " \ + "nfsroot=${serverip}:${rootpath} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:" \ + "${netmask}:${hostname}:${netdev}:off " \ + "console=${console},${baudrate} ${othbootargs}\0" \ + "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "mtdids=" MTDIDS_DEFAULT "\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv rootdev /dev/nfs;" \ + "run setipargs;run addmtd;" \ + "tftp ${loadaddr} ${bootfile};" \ + "tftp ${fdtaddr} ${fdtfile};" \ + "fdt addr ${fdtaddr};" \ + "bootm ${loadaddr} - ${fdtaddr}" + +/* UBI Support */ +#define CONFIG_CMD_NAND_TRIMFFS +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#define CONFIG_RBTREE +#define CONFIG_LZO +#define CONFIG_MTD_PARTITIONS + +/* bootcount support */ +#define CONFIG_BOOTCOUNT_LIMIT +#define CONFIG_BOOTCOUNT_I2C +#define CONFIG_BOOTCOUNT_ALEN 1 +#define CONFIG_SYS_BOOTCOUNT_ADDR 0x9 + +#define CONFIG_VERSION_VARIABLE + +#define CONFIG_FIT +#define CONFIG_FIT_SIGNATURE +#define CONFIG_CMD_FDT +#define CONFIG_CMD_HASH +#define CONFIG_RSA +#define CONFIG_SHA1 +#define CONFIG_SHA256 +#define CONFIG_OF_CONTROL + +#endif /* __CONFIG_H */ |