diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/hmi1001.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/hmi1001.h | 339 |
1 files changed, 339 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/hmi1001.h b/qemu/roms/u-boot/include/configs/hmi1001.h new file mode 100644 index 000000000..a1a88b5e3 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/hmi1001.h @@ -0,0 +1,339 @@ +/* + * (C) Copyright 2003-2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ +#define CONFIG_HMI1001 1 /* HMI1001 board */ + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xFFF00000 +#endif + +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ + +#define CONFIG_BOARD_EARLY_INIT_R + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* Partitions */ +#define CONFIG_DOS_PARTITION + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DISPLAY +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SNTP + + +#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ + +#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */ +# define CONFIG_SYS_LOWBOOT 1 +#endif + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm ${kernel_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ + "rootpath=/opt/eldk/ppc_82xx\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run net_nfs" + +#define CONFIG_MISC_INIT_R 1 + +/* + * IPB Bus clocking configuration. + */ +#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ + +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* + * EEPROM configuration + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* + * RTC configuration + */ +#define CONFIG_RTC_PCF8563 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 + +/* + * Flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xFF800000 + +#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ +#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max num of sects on one chip */ + +#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks + (= chip selects) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_CFI_AMD_RESET + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x4000 +#define CONFIG_ENV_SECT_SIZE 0x20000 +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 +#define CONFIG_SYS_DISPLAY_BASE 0x80600000 +#define CONFIG_SYS_STATUS1_BASE 0x80600200 +#define CONFIG_SYS_STATUS2_BASE 0x80600300 + +/* Settings for XLB = 132 MHz */ +#define SDRAM_DDR 1 +#define SDRAM_MODE 0x018D0000 +#define SDRAM_EMODE 0x40090000 +#define SDRAM_CONTROL 0x714f0f00 +#define SDRAM_CONFIG1 0x73722930 +#define SDRAM_CONFIG2 0x47770000 +#define SDRAM_TAPDELAY 0x10000000 + +/* Use ON-Chip SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM + +/* preserve space for the post_word at end of on-chip SRAM */ +#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4) + +#ifdef CONFIG_POST +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE +#else +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE +#endif + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 +#define CONFIG_PHY_ADDR 0x00 +#define CONFIG_MII 1 /* MII PHY management */ + +/* + * GPIO configuration + */ +#define CONFIG_SYS_GPS_PORT_CONFIG 0x01051004 + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* Enable an alternate, more extensive memory test */ +#define CONFIG_SYS_ALT_MEMTEST + +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +/* + * Enable loopw command. + */ +#define CONFIG_LOOPW + +/* + * Various low-level settings + */ +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE + +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x0004FB00 +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE + +/* 8Mbit SRAM @0x80100000 */ +#define CONFIG_SYS_CS1_START 0x80100000 +#define CONFIG_SYS_CS1_SIZE 0x00100000 +#define CONFIG_SYS_CS1_CFG 0x19B00 + +/* FRAM 32Kbyte @0x80700000 */ +#define CONFIG_SYS_CS2_START 0x80700000 +#define CONFIG_SYS_CS2_SIZE 0x00008000 +#define CONFIG_SYS_CS2_CFG 0x19800 + +/* Display H1, Status Inputs, EPLD @0x80600000 */ +#define CONFIG_SYS_CS3_START 0x80600000 +#define CONFIG_SYS_CS3_SIZE 0x00100000 +#define CONFIG_SYS_CS3_CFG 0x00019800 + +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 + +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ + +#define CONFIG_IDE_PREINIT 1 + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA + +/* Offset for data I/O */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) + +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) + +/* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE 4 + +#define CONFIG_ATAPI 1 + +#define CONFIG_VIDEO_SMI_LYNXEM +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_VIDEO_LOGO + +/* + * PCI Mapping: + * 0x40000000 - 0x4fffffff - PCI Memory + * 0x50000000 - 0x50ffffff - PCI IO Space + */ +#define CONFIG_PCI 1 +#define CONFIG_PCI_PNP 1 +#define CONFIG_PCI_SCAN_SHOW 1 +#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 + +#define CONFIG_PCI_MEM_BUS 0x40000000 +#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE 0x10000000 + +#define CONFIG_PCI_IO_BUS 0x50000000 +#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS +#define CONFIG_PCI_IO_SIZE 0x01000000 + +#define CONFIG_SYS_ISA_IO CONFIG_PCI_IO_BUS + +/*---------------------------------------------------------------------*/ +/* Display addresses */ +/*---------------------------------------------------------------------*/ + +#define CONFIG_PDSP188x +#define CONFIG_SYS_DISP_CHR_RAM (CONFIG_SYS_DISPLAY_BASE + 0x38) +#define CONFIG_SYS_DISP_CWORD (CONFIG_SYS_DISPLAY_BASE + 0x30) + +#endif /* __CONFIG_H */ |