diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/edminiv2.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/edminiv2.h | 238 |
1 files changed, 238 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/edminiv2.h b/qemu/roms/u-boot/include/configs/edminiv2.h new file mode 100644 index 000000000..8b9f66a29 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/edminiv2.h @@ -0,0 +1,238 @@ +/* + * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net> + * + * Based on original Kirkwood support which is + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_EDMINIV2_H +#define _CONFIG_EDMINIV2_H + +/* + * Version number information + */ + +#define CONFIG_IDENT_STRING " EDMiniV2" + +/* + * High Level Configuration Options (easy to change) + */ + +#define CONFIG_MARVELL 1 +#define CONFIG_ARM926EJS 1 /* Basic Architecture */ +#define CONFIG_FEROCEON 1 /* CPU Core subversion */ +#define CONFIG_ORION5X 1 /* SOC Family Name */ +#define CONFIG_88F5182 1 /* SOC Name */ +#define CONFIG_MACH_EDMINIV2 1 /* Machine type */ + +#include <asm/arch/orion5x.h> +/* + * CLKs configurations + */ + +/* + * Board-specific values for Orion5x MPP low level init: + * - MPPs 12 to 15 are SATA LEDs (mode 5) + * - Others are GPIO/unused (mode 3 for MPP0, mode 5 for + * MPP16 to MPP19, mode 0 for others + */ + +#define ORION5X_MPP0_7 0x00000003 +#define ORION5X_MPP8_15 0x55550000 +#define ORION5X_MPP16_23 0x00005555 + +/* + * Board-specific values for Orion5x GPIO low level init: + * - GPIO3 is input (RTC interrupt) + * - GPIO16 is Power LED control (0 = on, 1 = off) + * - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16) + * - GPIO18 is Power Button status (0 = Released, 1 = Pressed) + * - GPIO19 is SATA disk power toggle (toggles on 0-to-1) + * - GPIO22 is SATA disk power status () + * - GPIO23 is supply status for SATA disk () + * - GPIO24 is supply control for board (write 1 to power off) + * Last GPIO is 25, further bits are supposed to be 0. + * Enable mask has ones for INPUT, 0 for OUTPUT. + * Default is LED ON, board ON :) + */ + +#define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca +#define ORION5X_GPIO_OUT_VALUE 0x00000000 +#define ORION5X_GPIO_IN_POLARITY 0x000000d0 + +/* + * NS16550 Configuration + */ + +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK +#define CONFIG_SYS_NS16550_COM1 ORION5X_UART0_BASE + +/* + * Serial Port configuration + * The following definitions let you select what serial you want to use + * for your console driver. + */ + +#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE \ + { 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 } + +/* + * FLASH configuration + */ + +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_FLASH_CFI_LEGACY +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_BASE 0xfff80000 +#define CONFIG_SYS_FLASH_SECTSZ \ + {16384, 8192, 8192, 32768, \ + 65536, 65536, 65536, 65536, 65536, 65536, 65536} + +/* auto boot */ +#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ +#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ + +#define CONFIG_SYS_PROMPT "EDMiniV2> " /* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ + +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ +/* + * Commands configuration - using default command set for now + */ +#include <config_cmd_default.h> +#define CONFIG_CMD_IDE +#define CONFIG_CMD_I2C +#define CONFIG_CMD_USB + +/* + * Network + */ + +#ifdef CONFIG_CMD_NET +#define CONFIG_MVGBE /* Enable Marvell GbE Driver */ +#define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */ +#define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */ +#define CONFIG_PHY_BASE_ADR 0x8 +#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ +#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_MII /* expose smi ove miiphy interface */ +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ +#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ +#endif + +/* + * IDE + */ +#ifdef CONFIG_CMD_IDE +#define __io +#define CONFIG_IDE_PREINIT +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 +/* ED Mini V has an IDE-compatible SATA connector for port 1 */ +#define CONFIG_MVSATA_IDE +#define CONFIG_MVSATA_IDE_USE_PORT1 +/* Needs byte-swapping for ATA data register */ +#define CONFIG_IDE_SWAP_IO +/* Data, registers and alternate blocks are at the same offset */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) +#define CONFIG_SYS_ATA_REG_OFFSET (0x0100) +#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) +/* Each 8-bit ATA register is aligned to a 4-bytes address */ +#define CONFIG_SYS_ATA_STRIDE 4 +/* Controller supports 48-bits LBA addressing */ +#define CONFIG_LBA48 +/* A single bus, a single device */ +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE 1 +/* ATA registers base is at SATA controller base */ +#define CONFIG_SYS_ATA_BASE_ADDR ORION5X_SATA_BASE +/* ATA bus 0 is orion5x port 1 on ED Mini V2 */ +#define CONFIG_SYS_ATA_IDE0_OFFSET ORION5X_SATA_PORT1_OFFSET +/* end of IDE defines */ +#endif /* CMD_IDE */ + +/* + * Common USB/EHCI configuration + */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI /* Enable EHCI USB support */ +#define CONFIG_USB_EHCI_MARVELL +#define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE +#define CONFIG_USB_STORAGE +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION +#define CONFIG_SUPPORT_VFAT +#endif /* CONFIG_CMD_USB */ + +/* + * I2C related stuff + */ +#ifdef CONFIG_CMD_I2C +#define CONFIG_I2C_MVTWSI +#define CONFIG_I2C_MVTWSI_BASE ORION5X_TWSI_BASE +#define CONFIG_SYS_I2C_SLAVE 0x0 +#define CONFIG_SYS_I2C_SPEED 100000 +#endif + +/* + * Environment variables configurations + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SECT_SIZE 0x2000 /* 16K */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_OFFSET 0x4000 /* env starts here */ + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 256) /* 256kB for malloc() */ + +/* + * Other required minimal configurations + */ +#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ +#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ +#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ +#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ +#define CONFIG_NR_DRAM_BANKS 1 + +#define CONFIG_SYS_LOAD_ADDR 0x00800000 +#define CONFIG_SYS_MEMTEST_START 0x00400000 +#define CONFIG_SYS_MEMTEST_END 0x007fffff +#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 +#define CONFIG_SYS_MAXARGS 16 + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +/* Enable command line editing */ +#define CONFIG_CMDLINE_EDITING + +/* provide extensive help */ +#define CONFIG_SYS_LONGHELP + +/* additions for new relocation code, must be added to all boards */ +#define CONFIG_SYS_SDRAM_BASE 0 +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) + +#endif /* _CONFIG_EDMINIV2_H */ |