diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/digsy_mtc.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/digsy_mtc.h | 490 |
1 files changed, 490 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/digsy_mtc.h b/qemu/roms/u-boot/include/configs/digsy_mtc.h new file mode 100644 index 000000000..2a8cb3940 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/digsy_mtc.h @@ -0,0 +1,490 @@ +/* + * (C) Copyright 2003-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2005-2007 + * Modified for InterControl digsyMTC MPC5200 board by + * Frank Bodammer, GCD Hard- & Software GmbH, + * frank.bodammer@gcd-solutions.de + * + * (C) Copyright 2009 Semihalf + * Optimized for digsyMTC by: Grzegorz Bernacki <gjb@semihalf.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ + +#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ +#define CONFIG_DIGSY_MTC 1 /* ... on InterControl digsyMTC board */ + +/* + * Valid values for CONFIG_SYS_TEXT_BASE are: + * 0xFFF00000 boot high (standard configuration) + * 0xFE000000 boot low + * 0x00100000 boot from RAM (for testing only) + */ +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Standard: boot high */ +#endif + +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 + +#define CONFIG_SYS_CACHELINE_SIZE 32 + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 4 /* console is on PSC4 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE \ + { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* + * PCI Mapping: + * 0x40000000 - 0x4fffffff - PCI Memory + * 0x50000000 - 0x50ffffff - PCI IO Space + */ +#define CONFIG_PCI 1 +#define CONFIG_PCI_PNP 1 +#define CONFIG_PCI_SCAN_SHOW 1 +#define CONFIG_PCI_BOOTDELAY 250 + +#define CONFIG_PCI_MEM_BUS 0x40000000 +#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE 0x10000000 + +#define CONFIG_PCI_IO_BUS 0x50000000 +#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS +#define CONFIG_PCI_IO_SIZE 0x01000000 + +/* + * Partitions + */ +#define CONFIG_DOS_PARTITION +#define CONFIG_BZIP2 + +/* + * Video + */ +#define CONFIG_VIDEO + +#ifdef CONFIG_VIDEO +#define CONFIG_VIDEO_MB862xx +#define CONFIG_VIDEO_MB862xx_ACCEL +#define CONFIG_VIDEO_CORALP +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_SPLASH_SCREEN +#define CONFIG_VIDEO_BMP_GZIP +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) /* decompressed img */ + +/* Coral-PA clock frequency, geo and other both 133MHz */ +#define CONFIG_SYS_MB862xx_CCF 0x00050000 +/* Video SDRAM parameters */ +#define CONFIG_SYS_MB862xx_MMR 0x11d7fa72 +#endif + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#ifdef CONFIG_VIDEO +#define CONFIG_CMD_BMP +#endif +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_SPI +#define CONFIG_CMD_USB + +#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) +#define CONFIG_SYS_LOWBOOT 1 +#endif + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 1 + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "fw_image=digsyMPC.img\0" \ + "mtcb_start=mtc led diag orange; run mtcb_1\0" \ + "mtcb_clearled=for x in user1 user2 usbpwr usbbusy; " \ + "do mtc led $x; done\0" \ + "mtcb_1=if mtc key; then run mtcb_clearled mtcb_update; " \ + "else run mtcb_fw; fi\0" \ + "mtcb_fw=if bootm ff000000; then echo FIRMWARE OK!; " \ + "else echo BAD FIRMWARE CRC!; mtc led diag red; fi\0" \ + "mtcb_update=mtc led user1 orange;" \ + "while mtc key; do ; done; run mtcb_2;\0" \ + "mtcb_2=mtc led user1 green 2; usb reset; run mtcb_usb1;\0" \ + "mtcb_usb1=if fatload usb 0 400000 script.img; " \ + "then run mtcb_doscript; else run mtcb_usb2; fi\0" \ + "mtcb_usb2=if fatload usb 0 400000 $fw_image; " \ + "then run mtcb_dousb; else run mtcb_ide; fi\0" \ + "mtcb_doscript=run mtcb_usbleds; mtc led user2 orange 2; " \ + "run mtcb_wait_flickr mtcb_ds_1;\0" \ + "mtcb_ds_1=if imi 400000; then mtc led usbbusy; " \ + "source 400000; else run mtcb_error; fi\0" \ + "mtcb_dousb=run mtcb_usbleds mtcb_wait_flickr mtcb_du_1;\0" \ + "mtcb_du_1=if imi 400000; then run mtcb_du_2; " \ + "else run mtcb_error; fi\0" \ + "mtcb_du_2=run mtcb_clear mtcb_prog; mtc led usbbusy; " \ + "run mtcb_checkfw\0" \ + "mtcb_checkfw=if imi ff000000; then run mtcb_success; " \ + "else run mtcb_error; fi\0" \ + "mtcb_waitkey=mtc key; until test $? -eq 0; do mtc key; done\0" \ + "mtcb_wait_flickr=run mtcb_waitkey mtcb_uledflckr\0" \ + "mtcb_usbleds=mtc led usbpwr green; mtc led usbbusy orange 1;\0"\ + "mtcb_uledflckr=mtc led user1 orange 11\0" \ + "mtcb_error=mtc led user1 red\0" \ + "mtcb_clear=erase ff000000 ff0fffff\0" \ + "mtcb_prog=cp.b 400000 ff000000 ${filesize}\0" \ + "mtcb_success=mtc led user1 green\0" \ + "mtcb_ide=if fatload ide 0 400000 $fw_image;" \ + "then run mtcb_doide; else run mtcb_error; fi\0" \ + "mtcb_doide=mtc led user2 green 1;" \ + "run mtcb_wait_flickr mtcb_di_1;\0" \ + "mtcb_di_1=if imi 400000; then run mtcb_di_2;" \ + "else run mtcb_error; fi\0" \ + "mtcb_di_2=run mtcb_clear; run mtcb_prog mtcb_checkfw\0" \ + "ramdisk_num_sector=16\0" \ + "flash_base=ff000000\0" \ + "flashdisk_size=e00000\0" \ + "env_sector=fff60000\0" \ + "flashdisk_start=ff100000\0" \ + "load_cmd=tftp 400000 digsyMPC.img\0" \ + "clear_cmd=erase ff000000 ff0fffff\0" \ + "flash_cmd=cp.b 400000 ff000000 ${filesize}\0" \ + "update_cmd=run load_cmd; " \ + "iminfo 400000; " \ + "run clear_cmd flash_cmd; " \ + "iminfo ff000000\0" \ + "spi_driver=yes\0" \ + "spi_watchdog=no\0" \ + "ftps_start=yes\0" \ + "ftps_user1=admin\0" \ + "ftps_pass1=admin\0" \ + "ftps_base1=/\0" \ + "ftps_home1=/\0" \ + "plc_sio_srv=no\0" \ + "plc_sio_baud=57600\0" \ + "plc_sio_parity=no\0" \ + "plc_sio_stop=1\0" \ + "plc_sio_com=2\0" \ + "plc_eth_srv=yes\0" \ + "plc_eth_port=1200\0" \ + "plc_root=/ide/\0" \ + "diag_level=0\0" \ + "webvisu=no\0" \ + "plc_can1_routing=no\0" \ + "plc_can1_baudrate=250\0" \ + "plc_can2_routing=no\0" \ + "plc_can2_baudrate=250\0" \ + "plc_can3_routing=no\0" \ + "plc_can3_baudrate=250\0" \ + "plc_can4_routing=no\0" \ + "plc_can4_baudrate=250\0" \ + "netdev=eth0\0" \ + "console=ttyPSC0\0" \ + "kernel_addr_r=400000\0" \ + "fdt_addr_r=600000\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:" \ + "${netmask}:${hostname}:${netdev}:off panic=1\0" \ + "addcons=setenv bootargs ${bootargs} console=${console},${baudrate}\0"\ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ + "tftp ${fdt_addr_r} ${fdt_file};" \ + "run nfsargs addip addcons;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "load=tftp 200000 ${u-boot}\0" \ + "update=protect off FFF00000 +${filesize};" \ + "erase FFF00000 +${filesize};" \ + "cp.b 200000 FFF00000 ${filesize};" \ + "protect on FFF00000 +${filesize}\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run mtcb_start" + +/* + * SPI configuration + */ +#define CONFIG_HARD_SPI 1 +#define CONFIG_MPC52XX_SPI 1 + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 +#define CONFIG_SYS_I2C_MODULE 1 +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* + * EEPROM configuration + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 + +/* + * RTC configuration + */ +#if defined(CONFIG_DIGSY_REV5) +#define CONFIG_SYS_I2C_RTC_ADDR 0x56 +#define CONFIG_RTC_RV3029 +/* Enable 5k Ohm trickle charge resistor */ +#define CONFIG_SYS_RV3029_TCR 0x20 +#else +#define CONFIG_RTC_DS1337 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_DS1339_TCR_VAL 0xAB /* diode + 4k resistor */ +#endif + +/* + * Flash configuration + */ +#define CONFIG_SYS_FLASH_CFI 1 +#define CONFIG_FLASH_CFI_DRIVER 1 + +#if defined(CONFIG_DIGSY_REV5) +#define CONFIG_SYS_FLASH_BASE 0xFE000000 +#define CONFIG_SYS_FLASH_BASE_CS1 0xFC000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \ + CONFIG_SYS_FLASH_BASE_CS1} +#define CONFIG_SYS_UPDATE_FLASH_SIZE +#define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE +#else +#define CONFIG_SYS_FLASH_BASE 0xFF000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } +#endif + +#define CONFIG_SYS_MAX_FLASH_SECT 256 +#define CONFIG_FLASH_16BIT +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +#define CONFIG_SYS_FLASH_SIZE 0x01000000 +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 + +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,5200@0" +#define OF_SOC "soc5200@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) + +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_MISC_INIT_R + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#if defined(CONFIG_LOWBOOT) +#define CONFIG_ENV_ADDR 0xFF060000 +#else /* CONFIG_LOWBOOT */ +#define CONFIG_ENV_ADDR 0xFFF60000 +#endif /* CONFIG_LOWBOOT */ +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_SECT_SIZE 0x20000 +#define CONFIG_ENV_OVERWRITE 1 + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#if !defined(CONFIG_SYS_LOWBOOT) +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 +#else +#define CONFIG_SYS_DEFAULT_MBAR 0xF0000000 +#endif + +/* + * Use SRAM until RAM will be available + */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE + +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) +#define CONFIG_SYS_MALLOC_LEN (4096 << 10) +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 +#if defined(CONFIG_DIGSY_REV5) +#define CONFIG_PHY_ADDR 0x01 +#else +#define CONFIG_PHY_ADDR 0x00 +#endif +#define CONFIG_PHY_RESET_DELAY 1000 + +#define CONFIG_NETCONSOLE /* include NetConsole support */ + +/* + * GPIO configuration + * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1) + * Bit 0 (mask 0x80000000) : 0x1 + * SPI on Tmr2/3/4/5 pins + * Bit 2:3 (mask 0x30000000) : 0x2 + * ATA cs0/1 on csb_4/5 + * Bit 6:7 (mask 0x03000000) : 0x2 + * Ethernet 100Mbit with MD + * Bits 12:15 (mask 0x000f0000): 0x5 + * USB - Two UARTs + * Bits 18:19 (mask 0x00003000) : 0x2 + * PSC3 - USB2 on PSC3 + * Bits 20:23 (mask 0x00000f00) : 0x1 + * PSC2 - CAN1&2 on PSC2 pins + * Bits 25:27 (mask 0x00000070) : 0x1 + * PSC1 - AC97 functionality + * Bits 29:31 (mask 0x00000007) : 0x2 + */ +#define CONFIG_SYS_GPS_PORT_CONFIG 0xA2552112 + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE 1 +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_SYS_HUSH_PARSER + +#define CONFIG_AUTOBOOT_KEYED +#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n", bootdelay +#define CONFIG_AUTOBOOT_DELAY_STR " " + +#define CONFIG_LOOPW 1 +#define CONFIG_MX_CYCLIC 1 +#define CONFIG_ZERO_BOOTDELAY_CHECK + +#define CONFIG_SYS_CBSIZE 1024 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 32 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_SYS_MEMTEST_SCRATCH 0x00001000 +#define CONFIG_SYS_MEMTEST_START 0x00010000 +#define CONFIG_SYS_MEMTEST_END 0x019fffff + +#define CONFIG_SYS_LOAD_ADDR 0x00100000 + +/* + * Various low-level settings + */ +#define CONFIG_SYS_SDRAM_CS1 1 +#define CONFIG_SYS_XLB_PIPELINING 1 + +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE + +#if defined(CONFIG_SYS_LOWBOOT) +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x0002DD00 +#endif + +#define CONFIG_SYS_CS4_START 0x60000000 +#define CONFIG_SYS_CS4_SIZE 0x1000 +#define CONFIG_SYS_CS4_CFG 0x0008FC00 + +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS0_CFG 0x0002DD00 + +#if defined(CONFIG_DIGSY_REV5) +#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE_CS1 +#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS1_CFG 0x0002DD00 +#endif + +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x11111111 + +#if !defined(CONFIG_SYS_LOWBOOT) +#define CONFIG_SYS_RESET_ADDRESS 0xfff00100 +#else +#define CONFIG_SYS_RESET_ADDRESS 0xff000100 +#endif + +/* + * USB + */ +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_OHCI_BE_CONTROLLER +#define CONFIG_USB_STORAGE + +#define CONFIG_USB_CLOCK 0x00013333 +#define CONFIG_USB_CONFIG 0x00002000 + +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 +#define CONFIG_SYS_USB_OHCI_REGS_BASE MPC5XXX_USB +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mpc5200" +#define CONFIG_SYS_USB_OHCI_CPU_INIT + +/* + * IDE/ATA + */ +#define CONFIG_IDE_RESET +#define CONFIG_IDE_PREINIT + +#define CONFIG_SYS_ATA_CS_ON_I2C2 +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE 1 + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) +#define CONFIG_SYS_ATA_STRIDE 4 + +#define CONFIG_ATAPI 1 +#define CONFIG_LBA48 1 + +#endif /* __CONFIG_H */ |