diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/bf537-stamp.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/bf537-stamp.h | 288 |
1 files changed, 288 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/bf537-stamp.h b/qemu/roms/u-boot/include/configs/bf537-stamp.h new file mode 100644 index 000000000..a302f839a --- /dev/null +++ b/qemu/roms/u-boot/include/configs/bf537-stamp.h @@ -0,0 +1,288 @@ +/* + * U-boot - Configuration file for BF537 STAMP board + */ + +#ifndef __CONFIG_BF537_STAMP_H__ +#define __CONFIG_BF537_STAMP_H__ + +#include <asm/config-pre.h> + + +/* + * Processor Settings + */ +#define CONFIG_BFIN_CPU bf537-0.2 +#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS + + +/* + * Clock Settings + * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV + * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV + */ +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 25000000 +/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ +/* 1 = CLKIN / 2 */ +#define CONFIG_CLKIN_HALF 0 +/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ +/* 1 = bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ +/* Values can range from 0-63 (where 0 means 64) */ +#define CONFIG_VCO_MULT 20 +/* CCLK_DIV controls the core clock divider */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* SCLK_DIV controls the system clock divider */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 4 + + +/* + * Memory Settings + */ +#define CONFIG_MEM_ADD_WDTH 10 +#define CONFIG_MEM_SIZE 64 + +#define CONFIG_EBIU_SDRRC_VAL 0x306 +#define CONFIG_EBIU_SDGCTL_VAL 0x91114d + +#define CONFIG_EBIU_AMGCTL_VAL 0xFF +#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 + +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) +#define CONFIG_SYS_MALLOC_LEN (384 * 1024) + + +/* + * Network Settings + */ +#ifndef __ADSPBF534__ +#define ADI_CMDS_NETWORK 1 +#define CONFIG_BFIN_MAC +#define CONFIG_NETCONSOLE 1 +#endif +#define CONFIG_HOSTNAME bf537-stamp +/* Uncomment next line to use fixed MAC address */ +/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ +#define CONFIG_LIB_RAND + +/* + * Flash Settings + */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_BASE 0x20000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +/* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */ +#define CONFIG_SYS_MAX_FLASH_SECT 71 + + +/* + * SPI Settings + */ +#define CONFIG_BFIN_SPI +#define CONFIG_ENV_SPI_MAX_HZ 30000000 +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_ALL + + +/* + * Env Storage Settings + */ +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x10000 +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OFFSET 0x4000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x2000 +#endif +#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) +#define ENV_IS_EMBEDDED +#else +#define CONFIG_ENV_IS_EMBEDDED_IN_LDR +#endif +#ifdef ENV_IS_EMBEDDED +/* WARNING - the following is hand-optimized to fit within + * the sector before the environment sector. If it throws + * an error during compilation remove an object here to get + * it linked after the configuration sector. + */ +# define LDS_BOARD_TEXT \ + arch/blackfin/lib/built-in.o (.text*); \ + arch/blackfin/cpu/built-in.o (.text*); \ + . = DEFINED(env_offset) ? env_offset : .; \ + common/env_embedded.o (.text*); +#endif + + +/* + * I2C Settings + */ +#define CONFIG_BFIN_TWI_I2C 1 +#define CONFIG_HARD_I2C 1 + + +/* + * SPI_MMC Settings + */ +#define CONFIG_MMC_SPI +#ifdef CONFIG_MMC_SPI +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#endif + +/* + * NAND Settings + */ +/* #define CONFIG_NAND_PLAT */ +#ifdef CONFIG_NAND_PLAT +#define CONFIG_SYS_NAND_BASE 0x20212000 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 + +#define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) +#define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1)) +#define BFIN_NAND_WRITE(addr, cmd) \ + do { \ + bfin_write8(addr, cmd); \ + SSYNC(); \ + } while (0) + +#define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) +#define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) +#define NAND_PLAT_GPIO_DEV_READY GPIO_PF3 +#endif /* CONFIG_NAND_PLAT */ + +/* + * CF-CARD IDE-HDD Support + */ + +/* + * Add CF flash card support in TRUE-IDE Mode (CF-IDE-NAND Card) + * Strange address mapping Blackfin A13 connects to CF_A0 + */ + +/* #define CONFIG_BFIN_TRUE_IDE */ + +/* + * Add CF flash card support in Common Memory Mode (CF-IDE-NAND Card) + * This should be the preferred mode + */ + +/* #define CONFIG_BFIN_CF_IDE */ + +/* + * Add IDE Disk Drive (HDD) support + * See example interface here: + * http://docs.blackfin.uclinux.org/doku.php?id=linux-kernel:drivers:ide-blackfin + */ + +/* #define CONFIG_BFIN_HDD_IDE */ + +#if defined(CONFIG_BFIN_CF_IDE) || \ + defined(CONFIG_BFIN_HDD_IDE) || \ + defined(CONFIG_BFIN_TRUE_IDE) +# define CONFIG_BFIN_IDE 1 +# define CONFIG_CMD_IDE +#endif + +#if defined(CONFIG_BFIN_IDE) + +#define CONFIG_DOS_PARTITION 1 +/* + * IDE/ATA stuff + */ +#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ +#undef CONFIG_IDE_RESET /* no reset for ide supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) + +#undef CONFIG_EBIU_AMBCTL1_VAL +#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC3FFC3 + +#define CONFIG_CF_ATASEL_DIS 0x20311800 +#define CONFIG_CF_ATASEL_ENA 0x20311802 + +#if defined(CONFIG_BFIN_TRUE_IDE) +/* + * Note that these settings aren't for the most part used in include/ata.h + * when all of the ATA registers are setup + */ +#define CONFIG_SYS_ATA_BASE_ADDR 0x2031C000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */ +#define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A13 */ + +#elif defined(CONFIG_BFIN_CF_IDE) +#define CONFIG_SYS_ATA_BASE_ADDR 0x20211800 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* alternate registers */ +#define CONFIG_SYS_ATA_STRIDE 1 /* CF_A0=0, with /CE1 /CE2 odd/even byte selects */ + +#elif defined(CONFIG_BFIN_HDD_IDE) +#define CONFIG_SYS_ATA_BASE_ADDR 0x20314000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */ +#define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */ +#undef CONFIG_SCLK_DIV +#define CONFIG_SCLK_DIV 8 +#endif + +#endif + + +/* + * Misc Settings + */ +#define CONFIG_MISC_INIT_R +#define CONFIG_RTC_BFIN +#define CONFIG_UART_CONSOLE 0 +#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED + +/* Define if want to do post memory test */ +#undef CONFIG_POST +#ifdef CONFIG_POST +#define CONFIG_SYS_POST_HOTKEYS_GPIO GPIO_PF5 +#define CONFIG_POST_BSPEC1_GPIO_LEDS \ + GPIO_PF6, GPIO_PF7, GPIO_PF8, GPIO_PF9, GPIO_PF10, GPIO_PF11, +#define CONFIG_POST_BSPEC2_GPIO_BUTTONS \ + GPIO_PF5, GPIO_PF4, GPIO_PF3, GPIO_PF2, +#define CONFIG_POST_BSPEC2_GPIO_NAMES \ + 10, 11, 12, 13, +#define CONFIG_SYS_POST_FLASH_START 11 +#define CONFIG_SYS_POST_FLASH_END 71 +#endif + +/* These are for board tests */ +#if 0 +#define CONFIG_BOOTCOMMAND "bootldr 0x203f0100" +#define CONFIG_AUTOBOOT_KEYED +#define CONFIG_AUTOBOOT_PROMPT \ + "autoboot in %d seconds: press space to stop\n", bootdelay +#define CONFIG_AUTOBOOT_STOP_STR " " +#endif + + +/* + * Pull in common ADI header for remaining command/environment setup + */ +#include <configs/bfin_adi_common.h> + +#endif |