1 files changed, 185 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/atngw100mkii.h b/qemu/roms/u-boot/include/configs/atngw100mkii.h
new file mode 100644
index 000000000..066d09ab0
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/atngw100mkii.h
@@ -0,0 +1,185 @@
+/*
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * Copyright (C) 2012 Andreas Bießmann <andreas.devel@googlemail.com>
+ *
+ * Configuration settings for the AVR32 Network Gateway
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/hardware.h>
+
+#define CONFIG_AT32AP
+#define CONFIG_AT32AP7000
+#define CONFIG_ATNGW100MKII
+
+/*
+ * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
+ * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
+ * and the PBA bus to run at 1/4 the PLL frequency.
+ */
+#define CONFIG_PLL
+#define CONFIG_SYS_POWER_MANAGER
+#define CONFIG_SYS_OSC0_HZ		20000000
+#define CONFIG_SYS_PLL0_DIV		1
+#define CONFIG_SYS_PLL0_MUL		7
+#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES	16
+/*
+ * Set the CPU running at:
+ * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz
+ */
+#define CONFIG_SYS_CLKDIV_CPU		0
+/*
+ * Set the HSB running at:
+ * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz
+ */
+#define CONFIG_SYS_CLKDIV_HSB		1
+/*
+ * Set the PBA running at:
+ * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz
+ */
+#define CONFIG_SYS_CLKDIV_PBA		2
+/*
+ * Set the PBB running at:
+ * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz
+ */
+#define CONFIG_SYS_CLKDIV_PBB		1
+
+/* Reserve VM regions for NOR flash, NAND flash and SDRAM */
+#define CONFIG_SYS_NR_VM_REGIONS	3
+
+/*
+ * The PLLOPT register controls the PLL like this:
+ *   icp = PLLOPT<2>
+ *   ivco = PLLOPT<1:0>
+ *
+ * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
+ */
+#define CONFIG_SYS_PLL0_OPT		0x04
+
+#define CONFIG_USART_BASE		ATMEL_BASE_USART1
+#define CONFIG_USART_ID			1
+
+/* User serviceable stuff */
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+#define CONFIG_STACKSIZE		(2048)
+
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_BOOTARGS							\
+	"root=mtd:main rootfstype=jffs2"
+#define CONFIG_BOOTCOMMAND						\
+	"fsload 0x10400000 /uImage; bootm"
+
+/*
+ * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
+ * data on the serial line may interrupt the boot sequence.
+ */
+#define CONFIG_BOOTDELAY		1
+#define CONFIG_AUTOBOOT
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT		\
+	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
+#define CONFIG_AUTOBOOT_DELAY_STR	"d"
+#define CONFIG_AUTOBOOT_STOP_STR	" "
+
+/*
+ * After booting the board for the first time, new ethernet addresses
+ * should be generated and assigned to the environment variables
+ * "ethaddr" and "eth1addr". This is normally done during production.
+ */
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+#define CONFIG_NET_MULTI
+
+/*
+ * BOOTP/DHCP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_MII
+
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_XIMG
+
+#define CONFIG_ATMEL_USART
+#define CONFIG_MACB
+#define CONFIG_PORTMUX_PIO
+#define CONFIG_SYS_NR_PIOS		5
+#define CONFIG_SYS_HSDRAMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_ATMEL_MCI
+#define CONFIG_GENERIC_MMC
+#define CONFIG_ATMEL_SPI
+
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+
+#define CONFIG_SYS_DCACHE_LINESZ	32
+#define CONFIG_SYS_ICACHE_LINESZ	32
+
+#define CONFIG_NR_DRAM_BANKS		1
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_PROTECTION
+
+#define CONFIG_SYS_FLASH_BASE		0x00000000
+#define CONFIG_SYS_FLASH_SIZE		0x800000
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_MAX_FLASH_SECT	135
+
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_SYS_INTRAM_BASE		INTERNAL_SRAM_BASE
+#define CONFIG_SYS_INTRAM_SIZE		INTERNAL_SRAM_SIZE
+#define CONFIG_SYS_SDRAM_BASE		EBI_SDRAM_BASE
+
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SIZE			65536
+#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
+
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
+
+#define CONFIG_SYS_MALLOC_LEN		(256*1024)
+#define CONFIG_SYS_DMA_ALLOC_LEN	(16384)
+
+/* Allow 4MB for the kernel run-time image */
+#define CONFIG_SYS_LOAD_ADDR		(EBI_SDRAM_BASE + 0x00400000)
+#define CONFIG_SYS_BOOTPARAMS_LEN	(16 * 1024)
+
+/* Other configuration settings that shouldn't have to change all that often */
+#define CONFIG_SYS_PROMPT		"U-Boot> "
+#define CONFIG_SYS_CBSIZE		256
+#define CONFIG_SYS_MAXARGS		16
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP
+
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x1f00000)
+
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+
+#endif /* __CONFIG_H */