diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/alpr.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/alpr.h | 357 |
1 files changed, 357 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/alpr.h b/qemu/roms/u-boot/include/configs/alpr.h new file mode 100644 index 000000000..7849b222b --- /dev/null +++ b/qemu/roms/u-boot/include/configs/alpr.h @@ -0,0 +1,357 @@ +/* + * (C) Copyright 2006-2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_ALPR 1 /* Board is ebony */ +#define CONFIG_440GX 1 /* Specifc GX support */ +#define CONFIG_440 1 /* ... PPC440 family */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */ + +#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CONFIG_4xx_DCACHE /* Enable i- and d-cache */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CONFIG_SYS_FLASH_BASE 0xffe00000 /* start of FLASH */ +#define CONFIG_SYS_MONITOR_BASE 0xfffc0000 /* start of monitor */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CONFIG_SYS_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */ +#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ +#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 + + +#define CONFIG_SYS_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08300000) +#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer (placed in internal SRAM) + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_TEMP_STACK_OCM 1 +#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +#undef CONFIG_SYS_EXT_SERIAL_CLOCK +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_FLASH_CFI 1 /* The flash is CFI compatible */ +#define CONFIG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ + +#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ +#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */ +#undef CONFIG_SDRAM_ECC /* enable ECC support */ +#define CONFIG_SYS_SDRAM_TABLE { \ + {(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \ + {(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */ + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ + +/*----------------------------------------------------------------------- + * I2C EEPROM (PCF8594C) + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */ + /* 8 byte page write mode using */ + /* last 3 bits of the address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run kernelx\" to boot the system;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth3\0" \ + "hostname=alpr\0" \ + "fdt_file=alpr/alpr.dtb\0" \ + "fdt_addr=400000\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath} ${init}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \ + "mem=193M\0" \ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "net_nfs_fdt=tftp 200000 ${bootfile};" \ + "tftp ${fdt_addr} ${fdt_file};" \ + "run nfsargs addip addtty;" \ + "bootm 200000 - ${fdt_addr}\0" \ + "rootpath=/opt/projects/alpr/nfs_root\0" \ + "bootfile=/alpr/uImage\0" \ + "kernel_addr=fff00000\0" \ + "ramdisk_addr=fff10000\0" \ + "load=tftp 100000 /alpr/u-boot/u-boot.bin\0" \ + "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ + "cp.b 100000 fffc0000 40000;" \ + "setenv filesize;saveenv\0" \ + "upd=run load update\0" \ + "ethprime=ppc_4xx_eth3\0" \ + "ethact=ppc_4xx_eth3\0" \ + "autoload=no\0" \ + "ipconfig=dhcp;setenv serverip 11.0.0.152\0" \ + "load_fpga=fpga load 0 ffe00000 10dd9a\0" \ + "mtdargs=setenv bootargs root=/dev/mtdblock6 rw " \ + "rootfstype=jffs2 init=/sbin/init\0" \ + "kernel1_mtd=nand read 200000 0 200000;run mtdargs addip addtty"\ + ";bootm 200000\0" \ + "kernel2_mtd=nand read 200000 200000 200000;run mtdargs addip " \ + "addtty;bootm 200000\0" \ + "kernel1=setenv actkernel 'kernel1';run load_fpga " \ + "kernel1_mtd\0" \ + "kernel2=setenv actkernel 'kernel2';run load_fpga " \ + "kernel2_mtd\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run kernel2" + +#define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_PPC4xx_EMAC +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */ +#define CONFIG_PHY1_ADDR 0x03 /* dummy setting, no EMAC1 used */ +#define CONFIG_PHY2_ADDR 0x01 /* PHY address for EMAC2 */ +#define CONFIG_PHY3_ADDR 0x02 /* PHY address for EMAC3 */ +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH2 +#define CONFIG_HAS_ETH3 +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NETCONSOLE /* include NetConsole support */ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_FPGA +#define CONFIG_CMD_I2C +#undef CONFIG_CMD_LOADB +#undef CONFIG_CMD_LOADS +#define CONFIG_CMD_MII +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#undef CONFIG_CMD_NFS +#define CONFIG_CMD_PCI + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_ALT_MEMTEST 1 /* Enable more extensive memtest*/ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +#define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ +#define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/ + +/* Board-specific PCI */ +#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ +#define CONFIG_SYS_PCI_MASTER_INIT + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ + +/*----------------------------------------------------------------------- + * FPGA stuff + *-----------------------------------------------------------------------*/ +#define CONFIG_FPGA +#define CONFIG_FPGA_ALTERA +#define CONFIG_FPGA_CYCLON2 +#define CONFIG_SYS_FPGA_CHECK_CTRLC +#define CONFIG_SYS_FPGA_PROG_FEEDBACK +#define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in + Reihe geschaltet -> sollte gehen, + aufpassen mit Datasize ist jetzt + halt doppelt so gross ... Seite 306 + ist das mit den multiple Device in PS + Mode erklaert ...*/ + +/* FPGA program pin configuration */ +#define CONFIG_SYS_GPIO_CLK 18 /* FPGA clk pin (cpu output) */ +#define CONFIG_SYS_GPIO_DATA 19 /* FPGA data pin (cpu output) */ +#define CONFIG_SYS_GPIO_STATUS 20 /* FPGA status pin (cpu input) */ +#define CONFIG_SYS_GPIO_CONFIG 21 /* FPGA CONFIG pin (cpu output) */ +#define CONFIG_SYS_GPIO_CON_DON 22 /* FPGA CONFIG_DONE pin (cpu input) */ + +#define CONFIG_SYS_GPIO_SEL_DPR 14 /* cpu output */ +#define CONFIG_SYS_GPIO_SEL_AVR 15 /* cpu output */ +#define CONFIG_SYS_GPIO_PROG_EN 23 /* cpu output */ + +/*----------------------------------------------------------------------- + * Definitions for GPIO setup + *-----------------------------------------------------------------------*/ +#define CONFIG_SYS_GPIO_SHUTDOWN (0x80000000 >> 6) +#define CONFIG_SYS_GPIO_SSD_EMPTY (0x80000000 >> 9) +#define CONFIG_SYS_GPIO_EREADY (0x80000000 >> 26) +#define CONFIG_SYS_GPIO_REV0 (0x80000000 >> 14) +#define CONFIG_SYS_GPIO_REV1 (0x80000000 >> 15) + +/*----------------------------------------------------------------------- + * NAND-FLASH stuff + *-----------------------------------------------------------------------*/ +#define CONFIG_SYS_MAX_NAND_DEVICE 4 +#define CONFIG_SYS_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */ +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2, \ + CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 } +#define CONFIG_SYS_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */ +#define CONFIG_SYS_NAND_MAX_OOBFREE 2 +#define CONFIG_SYS_NAND_MAX_ECCPOS 56 + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE + +/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x92015480 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */ + +/* Memory Bank 1 (NAND-FLASH) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x01840380 /* TWT=3 */ +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#endif /* __CONFIG_H */ |