summaryrefslogtreecommitdiffstats
path: root/qemu/roms/u-boot/include/configs/VOM405.h
diff options
context:
space:
mode:
Diffstat (limited to 'qemu/roms/u-boot/include/configs/VOM405.h')
-rw-r--r--qemu/roms/u-boot/include/configs/VOM405.h274
1 files changed, 274 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/VOM405.h b/qemu/roms/u-boot/include/configs/VOM405.h
new file mode 100644
index 000000000..c06897b89
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/VOM405.h
@@ -0,0 +1,274 @@
+/*
+ * (C) Copyright 2001-2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_405EP 1 /* This is a PPC405 CPU */
+#define CONFIG_VOM405 1 /* ...on a VOM405 board */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFFC8000
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+
+#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
+
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#undef CONFIG_HAS_ETH1
+
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_EEPROM
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+
+#undef CONFIG_PRAM /* no "protected RAM" */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+
+#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CONFIG_SYS_BASE_BAUD 691200
+
+/* The following table includes the supported baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ 57600, 115200, 230400, 460800, 921600 }
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*
+ * FLASH organization
+ */
+#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
+
+#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
+#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
+#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
+#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
+#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1)
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024)
+
+#if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM)
+# define CONFIG_SYS_RAMBOOT 1
+#else
+# undef CONFIG_SYS_RAMBOOT
+#endif
+
+/*
+ * Environment Variable setup
+ */
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+ /* total size of a CAT24WC16 is 2048 bytes */
+
+#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
+#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */
+
+/*
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+/*
+ * External Bus Controller (EBC) Setup
+ */
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x92015480
+#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
+#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+
+/*
+ * FPGA stuff
+ */
+#define CONFIG_SYS_XSVF_DEFAULT_ADDR 0xfffc0000
+
+/* FPGA program pin configuration */
+#define CONFIG_SYS_FPGA_PRG 0x04000000 /* JTAG TMS pin (ppc output) */
+#define CONFIG_SYS_FPGA_CLK 0x02000000 /* JTAG TCK pin (ppc output) */
+#define CONFIG_SYS_FPGA_DATA 0x01000000 /* JTAG TDO->TDI data pin (ppc output) */
+#define CONFIG_SYS_FPGA_INIT 0x00010000 /* unused (ppc input) */
+#define CONFIG_SYS_FPGA_DONE 0x00008000 /* JTAG TDI->TDO pin (ppc input) */
+
+/*
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs -> GPIO
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+/* GPIO Input: OSR=00, ISR=00, TSR=00, TCR=0 */
+/* GPIO Output: OSR=00, ISR=00, TSR=00, TCR=1 */
+/* Alt. Funtion Input: OSR=00, ISR=01, TSR=00, TCR=0 */
+/* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
+#define CONFIG_SYS_GPIO0_OSRL 0x40000500 /* 0 ... 15 */
+#define CONFIG_SYS_GPIO0_OSRH 0x00000110 /* 16 ... 31 */
+#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 /* 0 ... 15 */
+#define CONFIG_SYS_GPIO0_ISR1H 0x14000045 /* 16 ... 31 */
+#define CONFIG_SYS_GPIO0_TSRL 0x00000000 /* 0 ... 15 */
+#define CONFIG_SYS_GPIO0_TSRH 0x00000000 /* 16 ... 31 */
+#define CONFIG_SYS_GPIO0_TCR 0xF7FE0014 /* 0 ... 31 */
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+
+#endif /* __CONFIG_H */