diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/R360MPI.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/R360MPI.h | 464 |
1 files changed, 464 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/R360MPI.h b/qemu/roms/u-boot/include/configs/R360MPI.h new file mode 100644 index 000000000..009d1cf97 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/R360MPI.h @@ -0,0 +1,464 @@ +/* + * (C) Copyright 2000-2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC823 1 /* This is a MPC823 CPU */ +#define CONFIG_R360MPI 1 + +#define CONFIG_SYS_TEXT_BASE 0x40000000 + +#define CONFIG_LCD +#define CONFIG_MPC8XX_LCD +#undef CONFIG_EDT32F10 +#define CONFIG_SHARP_LQ057Q3DC02 + +#define CONFIG_SPLASH_SCREEN + +#define MPC8XX_FACT 1 /* Multiply by 1 */ +#define MPC8XX_XIN 50000000 /* 50 MHz in */ +#define CONFIG_8xx_GCLK_FREQ 50000000 /* define if can't use get_gclk_freq */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 115200 /* console baudrate in bps */ +#if 0 +#define CONFIG_BOOTDELAY 0 /* immediate boot */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ + "bootm" + +#undef CONFIG_SCC1_ENET +#define CONFIG_SCC2_ENET + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#define CONFIG_MISC_INIT_R /* have misc_init_r() function */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_CAN_DRIVER /* CAN Driver support enabled */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#define CONFIG_HARD_I2C 1 /* To I2C with hardware support */ +#undef CONFIG_SYS_I2C_SOFT /* To I2C with software support */ +#define CONFIG_SYS_I2C_SPEED 4700 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +#if defined(CONFIG_SYS_I2C_SOFT) +#define CONFIG_SYS_SYS_I2C_SOFT_SPEED 4700 /* I2C speed and slave address */ +#define CONFIG_SYS_SYS_I2C_SOFT_SLAVE 0x7F +/* + * Software (bit-bang) I2C driver configuration + */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(50) +#endif /* #define(CONFIG_SYS_I2C_SOFT) */ + +#define CONFIG_SYS_I2C_LCD_ADDR 0x8 /* LCD Control */ +#define CONFIG_SYS_I2C_KEY_ADDR 0x9 /* Keyboard coprocessor */ +#define CONFIG_SYS_I2C_TEM_ADDR 0x49 /* Temperature Sensors */ + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_BMP +#define CONFIG_CMD_BSP +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCMCIA +#define CONFIG_CMD_SNTP + + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* we need the null device */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 /* must set console from env */ + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +/* + * JFFS2 partitions + */ +/* No command line, one static partition + * use all the space starting at offset 3MB*/ +#undef CONFIG_CMD_MTDPARTS +#define CONFIG_JFFS2_DEV "nor0" +#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF +#define CONFIG_JFFS2_PART_OFFSET 0x00300000 + +/* mtdparts command line support */ +/* +#define CONFIG_CMD_MTDPARTS +#define MTDIDS_DEFAULT "nor0=r360-0" +#define MTDPARTS_DEFAULT "mtdparts=r360-0:-@3m(user)" +*/ + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CONFIG_SYS_IMMR 0xFF000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0x40000000 +#if defined(DEBUG) +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment */ +#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment sector */ +#define CONFIG_ENV_SIZE 0x4000 /* Used Size of Environment sector */ +#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + * + * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! + */ +#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */ +#define CONFIG_SYS_PLPRCR \ + ( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST ) +#else /* up to 50 MHz we use a 1:1 clock */ +#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) +#endif /* CONFIG_80MHz */ + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CONFIG_SYS_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) +#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) +#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) +#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) + *----------------------------------------------------------------------- + */ + +#if 1 +#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ +#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR + +/* Offset for data I/O */ +#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for alternate registers */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 +#endif + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +#define CONFIG_SYS_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CONFIG_SYS_PRELIM_OR_AM 0xFF000000 /* OR addr mask */ + +/* + * FLASH timing: + */ +#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_SCY_7_CLK | OR_BI) + +#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) +#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) +#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) + + +/* + * BR2 and OR2 (SDRAM) + * + */ +#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ + +#define CONFIG_SYS_PRELIM_OR2_AM 0xF8000000 /* OR addr mask */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CONFIG_SYS_OR_TIMING_SDRAM (OR_ACS_DIV1 | OR_CSNT_SAM | \ + OR_SCY_0_CLK | OR_G5LS) + +#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR2_AM | CONFIG_SYS_OR_TIMING_SDRAM ) +#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +/* + * BR3 and OR3 (CAN Controller) + */ +#ifdef CONFIG_CAN_DRIVER +#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN base address */ +#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */ +#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA |OR_BI) +#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \ + BR_PS_8 | BR_MS_UPMB | BR_V) +#endif /* CONFIG_CAN_DRIVER */ + + +/* + * Memory Periodic Timer Prescaler + * + * The Divider for PTA (refresh timer) configuration is based on an + * example SDRAM configuration (64 MBit, one bank). The adjustment to + * the number of chip selects (NCS) and the actually needed refresh + * rate is done by setting MPTPR. + * + * PTA is calculated from + * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS) + * + * gclk CPU clock (not bus clock!) + * Trefresh Refresh cycle * 4 (four word bursts used) + * + * 4096 Rows from SDRAM example configuration + * 1000 factor s -> ms + * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration + * 4 Number of refresh cycles per period + * 64 Refresh cycle in ms per number of rows + * -------------------------------------------- + * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 + * + * 50 MHz => 50.000.000 / Divider = 98 + * 66 Mhz => 66.000.000 / Divider = 129 + * 80 Mhz => 80.000.000 / Divider = 156 + */ +#if defined(CONFIG_80MHz) +#define CONFIG_SYS_MAMR_PTA 156 +#elif defined(CONFIG_66MHz) +#define CONFIG_SYS_MAMR_PTA 129 +#else /* 50 MHz */ +#define CONFIG_SYS_MAMR_PTA 98 +#endif /*CONFIG_??MHz */ + +/* + * For 16 MBit, refresh rates could be 31.3 us + * (= 64 ms / 2K = 125 / quad bursts). + * For a simpler initialization, 15.6 us is used instead. + * + * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks + * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank + */ +#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* 9 column SDRAM */ +#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +#endif /* __CONFIG_H */ |