diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/PK1C20.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/PK1C20.h | 225 |
1 files changed, 0 insertions, 225 deletions
diff --git a/qemu/roms/u-boot/include/configs/PK1C20.h b/qemu/roms/u-boot/include/configs/PK1C20.h deleted file mode 100644 index e7d08647f..000000000 --- a/qemu/roms/u-boot/include/configs/PK1C20.h +++ /dev/null @@ -1,225 +0,0 @@ -/* - * (C) Copyright 2004, Psyent Corporation <www.psyent.com> - * Scott McNutt <smcnutt@psyent.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*------------------------------------------------------------------------ - * BOARD/CPU - *----------------------------------------------------------------------*/ -#define CONFIG_PK1C20 1 /* PK1C20 board */ -#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */ - -#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */ -#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/ -#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/ - -/*------------------------------------------------------------------------ - * CACHE -- the following will support II/s and II/f. The II/s does not - * have dcache, so the cache instructions will behave as NOPs. - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */ -#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */ -#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */ -#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */ - -/*------------------------------------------------------------------------ - * MEMORY BASE ADDRESSES - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */ -#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ -#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */ -#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */ -#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */ -#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB (only 1M mapped)*/ - -/*------------------------------------------------------------------------ - * MEMORY ORGANIZATION - * -Monitor at top. - * -The heap is placed below the monitor. - * -Global data is placed below the heap. - * -The stack is placed below global data (&grows down). - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 128k */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET - -/*------------------------------------------------------------------------ - * FLASH (AM29LV065D) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */ -#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char /* flash word size */ - -/*------------------------------------------------------------------------ - * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above - * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the - * reset address, no? This will keep the environment in user region - * of flash. NOTE: the monitor length must be multiple of sector size - * (which is common practice). - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */ -#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */ -#define CONFIG_ENV_OVERWRITE /* Serial change Ok */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_RESET_ADDR + CONFIG_SYS_MONITOR_LEN) - -/*------------------------------------------------------------------------ - * CONSOLE - *----------------------------------------------------------------------*/ -#define CONFIG_ALTERA_UART 1 /* Use altera uart */ -#if defined(CONFIG_ALTERA_JTAG_UART) -#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */ -#else -#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */ -#endif - -#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */ -#define CONFIG_BAUDRATE 115200 /* Initial baudrate */ -#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */ - -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/ - -/*------------------------------------------------------------------------ - * EPCS Device -- wne CONFIG_SYS_NIOS_EPCSBASE is defined code/commands for - * epcs device access is enabled. The base address is the epcs - * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK. - * The register base is currently at offset 0x600 from the memory base. - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_NIOS_EPCSBASE 0x02100200 /* EPCS register base */ - -/*------------------------------------------------------------------------ - * DEBUG - *----------------------------------------------------------------------*/ -#undef CONFIG_ROM_STUBS /* Stubs not in ROM */ - -/*------------------------------------------------------------------------ - * TIMEBASE -- - * - * The high res timer defaults to 1 msec. Since it includes the period - * registers, the interrupt frequency can be reduced using TMRCNT. - * If the default period is acceptable, TMRCNT can be left undefined. - * TMRMS represents the desired mecs per tick (msecs per interrupt). - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LOW_RES_TIMER -#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */ -#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */ -#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period */ -#define CONFIG_SYS_NIOS_TMRCNT \ - (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000)) - -/*------------------------------------------------------------------------ - * STATUS LED -- Provides a simple blinking led. For Nios2 each board - * must implement its own led routines -- leds are, after all, - * board-specific, no? - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */ -#define CONFIG_STATUS_LED /* Enable status driver */ -#define CONFIG_BOARD_SPECIFIC_LED - -#define STATUS_LED_BIT 1 /* Bit-0 on PIO */ -#define STATUS_LED_STATE 1 /* Blinking */ -#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */ - -/*------------------------------------------------------------------------ - * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ... - * and really doesn't need any additional clutter. So I choose the lazy - * way out to avoid changes there -- define the base address to ensure - * cache bypass so there's no need to monkey with inx/outx macros. - *----------------------------------------------------------------------*/ -#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */ -#define CONFIG_SMC91111 /* Using SMC91c111 */ -#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */ -#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */ - -#define CONFIG_ETHADDR 08:00:3e:26:0a:5b -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 192.168.2.21 -#define CONFIG_SERVERIP 192.168.2.16 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ - -#define CONFIG_CMD_BDI -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_IMI -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_LOADS -#define CONFIG_CMD_LOADB -#define CONFIG_CMD_MEMORY -#define CONFIG_CMD_MISC -#define CONFIG_CMD_NET -#define CONFIG_CMD_PING -#define CONFIG_CMD_RUN -#define CONFIG_CMD_SAVES - - -/*------------------------------------------------------------------------ - * COMPACT FLASH - *----------------------------------------------------------------------*/ -#if defined(CONFIG_CMD_IDE) -#define CONFIG_IDE_PREINIT /* Implement id_preinit */ -#define CONFIG_SYS_IDE_MAXBUS 1 /* 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_BASE_ADDR 0x00900800 /* ATA base addr */ -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 /* IDE0 offset */ -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0040 /* Data IO offset */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0040 /* Register offset */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 /* Alternate reg offset */ -#define CONFIG_SYS_ATA_STRIDE 4 /* Width betwix addrs */ -#define CONFIG_DOS_PARTITION - -/* Board-specific cf regs */ -#define CONFIG_SYS_CF_PRESENT 0x00900880 /* CF Present PIO base */ -#define CONFIG_SYS_CF_POWER 0x00900890 /* CF Power FET PIO base*/ -#define CONFIG_SYS_CF_ATASEL 0x009008a0 /* CF ATASEL PIO base */ - -#endif - -/*------------------------------------------------------------------------ - * JFFS2 - *----------------------------------------------------------------------*/ -#if defined(CONFIG_CMD_JFFS2) -#define CONFIG_SYS_JFFS_CUSTOM_PART /* board defined part */ -#endif - -/*------------------------------------------------------------------------ - * MISC - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_LONGHELP /* Provide extended help*/ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */ -#define CONFIG_SYS_MAXARGS 16 /* Max command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */ -#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */ -#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000 - -#define CONFIG_SYS_HUSH_PARSER - -#endif /* __CONFIG_H */ |