diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/MPC8540ADS.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/MPC8540ADS.h | 460 |
1 files changed, 0 insertions, 460 deletions
diff --git a/qemu/roms/u-boot/include/configs/MPC8540ADS.h b/qemu/roms/u-boot/include/configs/MPC8540ADS.h deleted file mode 100644 index 37c2b9415..000000000 --- a/qemu/roms/u-boot/include/configs/MPC8540ADS.h +++ /dev/null @@ -1,460 +0,0 @@ -/* - * Copyright 2004, 2011 Freescale Semiconductor. - * (C) Copyright 2002,2003 Motorola,Inc. - * Xianghua Xiao <X.Xiao@motorola.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * mpc8540ads board configuration file - * - * Please refer to doc/README.mpc85xx for more info. - * - * Make sure you change the MAC address and other network params first, - * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* High Level Configuration Options */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_MPC8540 1 /* MPC8540 specific */ -#define CONFIG_MPC8540ADS 1 /* MPC8540ADS board specific */ - -/* - * default CCARBAR is at 0xff700000 - * assume U-Boot is less than 0.5MB - */ -#define CONFIG_SYS_TEXT_BASE 0xfff80000 - -#ifndef CONFIG_HAS_FEC -#define CONFIG_HAS_FEC 1 /* 8540 has FEC */ -#endif - -#define CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ - -/* - * sysclk for MPC85xx - * - * Two valid values are: - * 33000000 - * 66000000 - * - * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz - * is likely the desired value here, so that is now the default. - * The board, however, can run at 66MHz. In any event, this value - * must match the settings of some switches. Details can be found - * in the README.mpc85xxads. - * - * XXX -- Can't we run at 66 MHz, anyway? PCI should drop to - * 33MHz to accommodate, based on a PCI pin. - * Note that PCI-X won't work at 33MHz. - */ - -#ifndef CONFIG_SYS_CLK_FREQ -#define CONFIG_SYS_CLK_FREQ 33000000 -#endif - - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ - -#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00400000 - -#define CONFIG_SYS_CCSRBAR 0xe0000000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ -#define CONFIG_SYS_FSL_DDR1 -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_SPD -#undef CONFIG_FSL_DDR_INTERACTIVE - -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) - -/* I2C addresses of SPD EEPROMs */ -#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ - -/* These are used when DDR doesn't use SPD. */ -#define CONFIG_SYS_SDRAM_SIZE 128 /* DDR is 128MB */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80000002 -#define CONFIG_SYS_DDR_TIMING_1 0x37344321 -#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ -#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ -#define CONFIG_SYS_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ -#define CONFIG_SYS_DDR_INTERVAL 0x05200100 /* autocharge,no open page */ - -/* - * SDRAM on the Local Bus - */ -#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ -#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ -#define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */ - -#define CONFIG_SYS_OR0_PRELIM 0xff006ff7 /* 16MB Flash */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_EMPTY_INFO - -#undef CONFIG_CLOCKS_IN_MHZ - - -/* - * Local Bus Definitions - */ - -/* - * Base Register 2 and Option Register 2 configure SDRAM. - * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. - * - * For BR2, need: - * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 - * port-size = 32-bits = BR2[19:20] = 11 - * no parity checking = BR2[21:22] = 00 - * SDRAM for MSEL = BR2[24:26] = 011 - * Valid = BR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 - * - * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into - * FIXME: the top 17 bits of BR2. - */ - -#define CONFIG_SYS_BR2_PRELIM 0xf0001861 - -/* - * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. - * - * For OR2, need: - * 64MB mask for AM, OR2[0:7] = 1111 1100 - * XAM, OR2[17:18] = 11 - * 9 columns OR2[19-21] = 010 - * 13 rows OR2[23-25] = 100 - * EAD set for extra time OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 - */ - -#define CONFIG_SYS_OR2_PRELIM 0xfc006901 - -#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ -#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ -#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ - -#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_BSMA1516 \ - | LSDMR_RFCR5 \ - | LSDMR_PRETOACT3 \ - | LSDMR_ACTTORW3 \ - | LSDMR_BL8 \ - | LSDMR_WRC2 \ - | LSDMR_CL3 \ - | LSDMR_RFEN \ - ) - -/* - * SDRAM Controller configuration sequence. - */ -#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) -#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) -#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) -#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) -#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) - - -/* - * 32KB, 8-bit wide for ADS config reg - */ -#define CONFIG_SYS_BR4_PRELIM 0xf8000801 -#define CONFIG_SYS_OR4_PRELIM 0xffffe1f1 -#define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000) - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ - -/* Serial Port */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER -#ifdef CONFIG_SYS_HUSH_PARSER -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* RapidIO MMU */ -#define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */ -#define CONFIG_SYS_RIO_MEM_BUS 0xc0000000 /* base address */ -#define CONFIG_SYS_RIO_MEM_PHYS 0xc0000000 -#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ - -#if defined(CONFIG_PCI) - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP - -#if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xe0000000 - #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ -#endif - -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - -#endif /* CONFIG_PCI */ - - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT - - -#if CONFIG_HAS_FEC -#define CONFIG_MPC85XX_FEC 1 -#define CONFIG_MPC85XX_FEC_NAME "FEC" -#define FEC_PHY_ADDR 3 -#define FEC_PHYIDX 0 -#define FEC_FLAGS 0 -#endif - -/* Options are: TSEC[0-1], FEC */ -#define CONFIG_ETHPRIME "TSEC0" - -#endif /* CONFIG_TSEC_ENET */ - - -/* - * Environment - */ -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) - #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ - #define CONFIG_ENV_SIZE 0x2000 -#else - #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ - #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PING -#define CONFIG_CMD_I2C -#define CONFIG_CMD_ELF -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_SETEXPR - -#if defined(CONFIG_PCI) - #define CONFIG_CMD_PCI -#endif - -#if defined(CONFIG_SYS_RAMBOOT) - #undef CONFIG_CMD_SAVEENV - #undef CONFIG_CMD_LOADS -#endif - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - - -/* - * Environment Configuration - */ - -/* The mac addresses for all ethernet interface */ -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_ETHADDR 00:E0:0C:00:00:FD -#define CONFIG_HAS_ETH1 -#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD -#define CONFIG_HAS_ETH2 -#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD -#endif - -#define CONFIG_IPADDR 192.168.1.253 - -#define CONFIG_HOSTNAME unknown -#define CONFIG_ROOTPATH "/nfsroot" -#define CONFIG_BOOTFILE "your.uImage" - -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_GATEWAYIP 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 - -#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ - -#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=1000000\0" \ - "ramdiskfile=your.ramdisk.u-boot\0" \ - "fdtaddr=400000\0" \ - "fdtfile=your.fdt.dtb\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND - -#endif /* __CONFIG_H */ |