diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/MPC8266ADS.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/MPC8266ADS.h | 563 |
1 files changed, 0 insertions, 563 deletions
diff --git a/qemu/roms/u-boot/include/configs/MPC8266ADS.h b/qemu/roms/u-boot/include/configs/MPC8266ADS.h deleted file mode 100644 index 8d9c8fb45..000000000 --- a/qemu/roms/u-boot/include/configs/MPC8266ADS.h +++ /dev/null @@ -1,563 +0,0 @@ -/* - * (C) Copyright 2001 - * Stuart Hughes <stuarth@lineo.com> - * This file is based on similar values for other boards found in other - * U-Boot config files, and some that I found in the mpc8260ads manual. - * - * Note: my board is a PILOT rev. - * Note: the mpc8260ads doesn't come with a proper Ethernet MAC address. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Config header file for a MPC8266ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm - */ - -/* !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! - !! !! - !! This configuration requires JP3 to be in position 1-2 to work !! - !! To make it work for the default, the CONFIG_SYS_TEXT_BASE define in !! - !! board/mpc8266ads/config.mk must be changed from 0xfe000000 to !! - !! 0xfff00000 !! - !! The CONFIG_SYS_HRCW_MASTER define below must also be changed to match !! - !! !! - !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC8266ADS 1 /* ...on motorola ADS board */ -#define CONFIG_CPM2 1 /* Has a CPM2 */ - -#define CONFIG_SYS_TEXT_BASE 0xfe000000 - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ - -/* allow serial and ethaddr to be overwritten */ -#define CONFIG_ENV_OVERWRITE - -/* - * select serial console configuration - * - * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - * - * if CONFIG_CONS_NONE is defined, then the serial console routines must - * defined elsewhere (for example, on the cogent platform, there are serial - * ports on the motherboard which are used for the serial console - see - * cogent/cma101/serial.[ch]). - */ -#undef CONFIG_CONS_ON_SMC /* define if console on SMC */ -#define CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ -#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ - -/* - * select ethernet configuration - * - * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then - * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 - * for FCC) - * - * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be - * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. - */ -#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ -#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ -#undef CONFIG_ETHER_NONE /* define if ether on something else */ -#define CONFIG_ETHER_INDEX 2 /* which channel for ether */ -#define CONFIG_MII /* MII PHY management */ -#define CONFIG_BITBANGMII /* bit-bang MII PHY management */ -/* - * Port pins used for bit-banged MII communictions (if applicable). - */ -#define MDIO_PORT 2 /* Port C */ -#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ - (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) -#define MDC_DECLARE MDIO_DECLARE - -#define MDIO_ACTIVE (iop->pdir |= 0x00400000) -#define MDIO_TRISTATE (iop->pdir &= ~0x00400000) -#define MDIO_READ ((iop->pdat & 0x00400000) != 0) - -#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ - else iop->pdat &= ~0x00400000 - -#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ - else iop->pdat &= ~0x00200000 - -#define MIIDELAY udelay(1) - -#if (CONFIG_ETHER_INDEX == 2) - -/* - * - Rx-CLK is CLK13 - * - Tx-CLK is CLK14 - * - Select bus for bd/buffers (see 28-13) - * - Half duplex - */ -# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) -# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) -# define CONFIG_SYS_CPMFCR_RAMTYPE 0 -# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) - -#endif /* CONFIG_ETHER_INDEX */ - -/* other options */ -#define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* PCI */ -#define CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_PCI_PNP -#define CONFIG_PCI_BOOTDELAY 0 -#undef CONFIG_PCI_SCAN_SHOW - -/*----------------------------------------------------------------------- - * Definitions for Serial Presence Detect EEPROM address - * (to get SDRAM settings) - */ -#define SPD_EEPROM_ADDRESS 0x50 - -#define CONFIG_8260_CLKIN 66000000 /* in Hz */ -#define CONFIG_BAUDRATE 115200 - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -/* Commands we want, that are not part of default set */ -#define CONFIG_CMD_ASKENV /* ask for env variable */ -#define CONFIG_CMD_CACHE /* icache, dcache */ -#define CONFIG_CMD_DHCP /* DHCP Support */ -#define CONFIG_CMD_DIAG /* Diagnostics */ -#define CONFIG_CMD_IMMAP /* IMMR dump support */ -#define CONFIG_CMD_IRQ /* irqinfo */ -#define CONFIG_CMD_MII /* MII support */ -#define CONFIG_CMD_PCI /* pciinfo */ -#define CONFIG_CMD_PING /* ping support */ -#define CONFIG_CMD_PORTIO /* Port I/O */ -#define CONFIG_CMD_REGINFO /* Register dump */ -#define CONFIG_CMD_SAVES /* save S record dump */ -#define CONFIG_CMD_SDRAM /* SDRAM DIMM SPD info printout */ - -/* Commands from default set we don't need */ -#undef CONFIG_CMD_FPGA /* FPGA configuration Support */ -#undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ - -/* Define a command string that is automatically executed when no character - * is read on the console interface withing "Boot Delay" after reset. - */ -#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */ -#define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */ - -#ifdef CONFIG_BOOT_ROOT_INITRD -#define CONFIG_BOOTCOMMAND \ - "version;" \ - "echo;" \ - "bootp;" \ - "setenv bootargs root=/dev/ram0 rw " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ - "bootm" -#endif /* CONFIG_BOOT_ROOT_INITRD */ - -#ifdef CONFIG_BOOT_ROOT_NFS -#define CONFIG_BOOTCOMMAND \ - "version;" \ - "echo;" \ - "bootp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ - "bootm" -#endif /* CONFIG_BOOT_ROOT_NFS */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_DNS - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#if defined(CONFIG_CMD_KGDB) -#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ -#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ -#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ -#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */ -#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ -#endif - -#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */ - /* for versions < 2.4.5-pre5 */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define FLASH_BASE 0xFE000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 32 /* max num of sects on one chip */ -#define CONFIG_SYS_FLASH_SIZE 8 -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */ - -#undef CONFIG_SYS_FLASH_CHECKSUM - -/* this is stuff came out of the Motorola docs */ -/* Only change this if you also change the Hardware configuration Word */ -#define CONFIG_SYS_DEFAULT_IMMR 0x0F010000 - -/* Set IMMR to 0xF0000000 or above to boot Linux */ -#define CONFIG_SYS_IMMR 0xF0000000 -#define CONFIG_SYS_BCSR 0xF8000000 -#define CONFIG_SYS_PCI_INT 0xF8200000 /* PCI interrupt controller */ - -/* Define CONFIG_VERY_BIG_RAM to allow use of SDRAMs larger than 256MBytes - */ -/*#define CONFIG_VERY_BIG_RAM 1*/ - -/* What should be the base address of SDRAM DIMM and how big is - * it (in Mbytes)? This will normally auto-configure via the SPD. -*/ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE 16 - -#define SDRAM_SPD_ADDR 0x50 - -/*----------------------------------------------------------------------- - * BR2,BR3 - Base Register - * Ref: Section 10.3.1 on page 10-14 - * OR2,OR3 - Option Register - * Ref: Section 10.3.2 on page 10-16 - *----------------------------------------------------------------------- - */ - -/* Bank 2,3 - SDRAM DIMM - */ - -/* The BR2 is configured as follows: - * - * - Base address of 0x00000000 - * - 64 bit port size (60x bus only) - * - Data errors checking is disabled - * - Read and write access - * - SDRAM 60x bus - * - Access are handled by the memory controller according to MSEL - * - Not used for atomic operations - * - No data pipelining is done - * - Valid - */ -#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_SDRAM_P |\ - BRx_V) - -#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_SDRAM_P |\ - BRx_V) - -/* With a 64 MB DIMM, the OR2 is configured as follows: - * - * - 64 MB - * - 4 internal banks per device - * - Row start address bit is A8 with PSDMR[PBI] = 0 - * - 12 row address lines - * - Back-to-back page mode - * - Internal bank interleaving within save device enabled - */ -#if (CONFIG_SYS_SDRAM_SIZE == 64) -#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM_SIZE) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI0_A8 |\ - ORxS_NUMR_12) -#elif (CONFIG_SYS_SDRAM_SIZE == 16) -#define CONFIG_SYS_OR2_PRELIM (0xFF000C80) -#else -#error "INVALID SDRAM CONFIGURATION" -#endif - -/*----------------------------------------------------------------------- - * PSDMR - 60x Bus SDRAM Mode Register - * Ref: Section 10.3.3 on page 10-21 - *----------------------------------------------------------------------- - */ - -#if (CONFIG_SYS_SDRAM_SIZE == 64) -/* With a 64 MB DIMM, the PSDMR is configured as follows: - * - * - Bank Based Interleaving, - * - Refresh Enable, - * - Address Multiplexing where A5 is output on A14 pin - * (A6 on A15, and so on), - * - use address pins A14-A16 as bank select, - * - A9 is output on SDA10 during an ACTIVATE command, - * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks, - * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command - * is 3 clocks, - * - earliest timing for READ/WRITE command after ACTIVATE command is - * 2 clocks, - * - earliest timing for PRECHARGE after last data was read is 1 clock, - * - earliest timing for PRECHARGE after last data was written is 1 clock, - * - CAS Latency is 2. - */ -#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\ - PSDMR_SDAM_A14_IS_A5 |\ - PSDMR_BSMA_A14_A16 |\ - PSDMR_SDA10_PBI0_A9 |\ - PSDMR_RFRC_7_CLK |\ - PSDMR_PRETOACT_3W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_1C |\ - PSDMR_CL_2) -#elif (CONFIG_SYS_SDRAM_SIZE == 16) -/* With a 16 MB DIMM, the PSDMR is configured as follows: - * - * configuration parameters found in Motorola documentation - */ -#define CONFIG_SYS_PSDMR (0x016EB452) -#else -#error "INVALID SDRAM CONFIGURATION" -#endif - -#define RS232EN_1 0x02000002 -#define RS232EN_2 0x01000001 -#define FETHIEN 0x08000008 -#define FETH_RST 0x04000004 - -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* Use this HRCW for booting from address 0xfe00000 (JP3 in setting 1-2) */ -/* 0x0EB2B645 */ -#define CONFIG_SYS_HRCW_MASTER (( HRCW_BPS11 | HRCW_CIP ) |\ - ( HRCW_L2CPC10 | HRCW_DPPC11 | HRCW_ISB010 ) |\ - ( HRCW_BMS | HRCW_MMR11 | HRCW_LBPC01 | HRCW_APPC10 ) |\ - ( HRCW_CS10PC01 | HRCW_MODCK_H0101 ) \ - ) - -/* Use this HRCW for booting from address 0xfff0000 (JP3 in setting 2-3) */ -/* #define CONFIG_SYS_HRCW_MASTER 0x0cb23645 */ - -/* This value should actually be situated in the first 256 bytes of the FLASH - which on the standard MPC8266ADS board is at address 0xFF800000 - The linker script places it at 0xFFF00000 instead. - - It still works, however, as long as the ADS board jumper JP3 is set to - position 2-3 so the board is using the BCSR as Hardware Configuration Word - - If you want to use the one defined here instead, ust copy the first 256 bytes from - 0xfff00000 to 0xff800000 (for 8MB flash) - - - Rune - -*/ - -/* no slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#ifndef CONFIG_SYS_RAMBOOT -# define CONFIG_ENV_IS_IN_FLASH 1 -# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) -# define CONFIG_ENV_SECT_SIZE 0x40000 -#else -# define CONFIG_ENV_IS_IN_NVRAM 1 -# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -# define CONFIG_ENV_SIZE 0x200 -#endif /* CONFIG_SYS_RAMBOOT */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * HIDx - Hardware Implementation-dependent Registers 2-11 - *----------------------------------------------------------------------- - * HID0 also contains cache control - initially enable both caches and - * invalidate contents, then the final state leaves only the instruction - * cache enabled. Note that Power-On and Hard reset invalidate the caches, - * but Soft reset does not. - * - * HID1 has only read-only information - nothing to set. - */ -/*#define CONFIG_SYS_HID0_INIT 0 */ -#define CONFIG_SYS_HID0_INIT (HID0_ICE |\ - HID0_DCE |\ - HID0_ICFI |\ - HID0_DCI |\ - HID0_IFEM |\ - HID0_ABE) - -#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE ) - -#define CONFIG_SYS_HID2 0 - -#define CONFIG_SYS_SYPCR 0xFFFFFFC3 -#define CONFIG_SYS_BCR 0x004C0000 -#define CONFIG_SYS_SIUMCR 0x4E64C000 -#define CONFIG_SYS_SCCR 0x00000000 - -/* local bus memory map - * - * 0x00000000-0x03FFFFFF 64MB SDRAM - * 0x80000000-0x9FFFFFFF 512MB outbound prefetchable PCI memory window - * 0xA0000000-0xBFFFFFFF 512MB outbound non-prefetchable PCI memory window - * 0xF0000000-0xF001FFFF 128KB MPC8266 internal memory - * 0xF4000000-0xF7FFFFFF 64MB outbound PCI I/O window - * 0xF8000000-0xF8007FFF 32KB BCSR - * 0xF8100000-0xF8107FFF 32KB ATM UNI - * 0xF8200000-0xF8207FFF 32KB PCI interrupt controller - * 0xF8300000-0xF8307FFF 32KB EEPROM - * 0xFE000000-0xFFFFFFFF 32MB flash - */ -#define CONFIG_SYS_BR0_PRELIM 0xFE001801 /* flash */ -#define CONFIG_SYS_OR0_PRELIM 0xFE000836 -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR | 0x1801) /* BCSR */ -#define CONFIG_SYS_OR1_PRELIM 0xFFFF8010 -#define CONFIG_SYS_BR4_PRELIM 0xF8300801 /* EEPROM */ -#define CONFIG_SYS_OR4_PRELIM 0xFFFF8846 -#define CONFIG_SYS_BR5_PRELIM 0xF8100801 /* PM5350 ATM UNI */ -#define CONFIG_SYS_OR5_PRELIM 0xFFFF8E36 -#define CONFIG_SYS_BR8_PRELIM (CONFIG_SYS_PCI_INT | 0x1801) /* PCI interrupt controller */ -#define CONFIG_SYS_OR8_PRELIM 0xFFFF8010 - -#define CONFIG_SYS_RMR 0x0001 -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) -#define CONFIG_SYS_RCCR 0 -#define CONFIG_SYS_MPTPR 0x00001900 -#define CONFIG_SYS_PSRT 0x00000021 - -/* This address must not exist */ -#define CONFIG_SYS_RESET_ADDRESS 0xFCFFFF00 - -/* PCI Memory map (if different from default map */ -#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE /* Local base */ -#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 /* PCI base */ -#define CONFIG_SYS_PICMR0_MASK_ATTRIB (PICMR_MASK_512MB | PICMR_ENABLE | \ - PICMR_PREFETCH_EN) - -/* - * These are the windows that allow the CPU to access PCI address space. - * All three PCI master windows, which allow the CPU to access PCI - * prefetch, non prefetch, and IO space (see below), must all fit within - * these windows. - */ - -/* PCIBR0 */ -#define CONFIG_SYS_PCI_MSTR0_LOCAL 0x80000000 /* Local base */ -#define CONFIG_SYS_PCIMSK0_MASK PCIMSK_1GB /* Size of window */ -/* PCIBR1 */ -#define CONFIG_SYS_PCI_MSTR1_LOCAL 0xF4000000 /* Local base */ -#define CONFIG_SYS_PCIMSK1_MASK PCIMSK_64MB /* Size of window */ - -/* - * Master window that allows the CPU to access PCI Memory (prefetch). - * This window will be setup with the first set of Outbound ATU registers - * in the bridge. - */ - -#define CONFIG_SYS_PCI_MSTR_MEM_LOCAL 0x80000000 /* Local base */ -#define CONFIG_SYS_PCI_MSTR_MEM_BUS 0x80000000 /* PCI base */ -#define CONFIG_SYS_CPU_PCI_MEM_START PCI_MSTR_MEM_LOCAL -#define CONFIG_SYS_PCI_MSTR_MEM_SIZE 0x20000000 /* 512MB */ -#define CONFIG_SYS_POCMR0_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN) - -/* - * Master window that allows the CPU to access PCI Memory (non-prefetch). - * This window will be setup with the second set of Outbound ATU registers - * in the bridge. - */ - -#define CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL 0xA0000000 /* Local base */ -#define CONFIG_SYS_PCI_MSTR_MEMIO_BUS 0xA0000000 /* PCI base */ -#define CONFIG_SYS_CPU_PCI_MEMIO_START PCI_MSTR_MEMIO_LOCAL -#define CONFIG_SYS_PCI_MSTR_MEMIO_SIZE 0x20000000 /* 512MB */ -#define CONFIG_SYS_POCMR1_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE) - -/* - * Master window that allows the CPU to access PCI IO space. - * This window will be setup with the third set of Outbound ATU registers - * in the bridge. - */ - -#define CONFIG_SYS_PCI_MSTR_IO_LOCAL 0xF4000000 /* Local base */ -#define CONFIG_SYS_PCI_MSTR_IO_BUS 0xF4000000 /* PCI base */ -#define CONFIG_SYS_CPU_PCI_IO_START PCI_MSTR_IO_LOCAL -#define CONFIG_SYS_PCI_MSTR_IO_SIZE 0x04000000 /* 64MB */ -#define CONFIG_SYS_POCMR2_MASK_ATTRIB (POCMR_MASK_64MB | POCMR_ENABLE | POCMR_PCI_IO) - -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition, whole device */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "" -#define MTDPARTS_DEFAULT "" -*/ - -#endif /* __CONFIG_H */ |