diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/M5253EVBE.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/M5253EVBE.h | 194 |
1 files changed, 0 insertions, 194 deletions
diff --git a/qemu/roms/u-boot/include/configs/M5253EVBE.h b/qemu/roms/u-boot/include/configs/M5253EVBE.h deleted file mode 100644 index fabfdb93d..000000000 --- a/qemu/roms/u-boot/include/configs/M5253EVBE.h +++ /dev/null @@ -1,194 +0,0 @@ -/* - * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. - * Hayden Fraser (Hayden.Fraser@freescale.com) - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _M5253EVBE_H -#define _M5253EVBE_H - -#define CONFIG_MCF52x2 /* define processor family */ -#define CONFIG_M5253 /* define processor type */ -#define CONFIG_M5253EVBE /* define board type */ - -#define CONFIG_MCFTMR - -#define CONFIG_MCFUART -#define CONFIG_SYS_UART_PORT (0) -#define CONFIG_BAUDRATE 115200 - -#undef CONFIG_WATCHDOG /* disable watchdog */ - -#define CONFIG_BOOTDELAY 5 - -/* Configuration for environment - * Environment is embedded in u-boot in the second sector of the flash - */ -#ifndef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_ENV_OFFSET 0x4000 -#define CONFIG_ENV_SECT_SIZE 0x2000 -#define CONFIG_ENV_IS_IN_FLASH 1 -#else -#define CONFIG_ENV_ADDR 0xffe04000 -#define CONFIG_ENV_SECT_SIZE 0x2000 -#define CONFIG_ENV_IS_IN_FLASH 1 -#endif - -/* - * BOOTP options - */ -#undef CONFIG_BOOTP_BOOTFILESIZE -#undef CONFIG_BOOTP_BOOTPATH -#undef CONFIG_BOOTP_GATEWAY -#undef CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> -#define CONFIG_CMD_CACHE -#undef CONFIG_CMD_NET -#define CONFIG_CMD_LOADB -#define CONFIG_CMD_LOADS -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_IDE -#define CONFIG_CMD_MEMORY -#define CONFIG_CMD_MISC - -/* ATA */ -#define CONFIG_DOS_PARTITION -#define CONFIG_MAC_PARTITION -#define CONFIG_IDE_RESET 1 -#define CONFIG_IDE_PREINIT 1 -#define CONFIG_ATAPI -#undef CONFIG_LBA48 - -#define CONFIG_SYS_IDE_MAXBUS 1 -#define CONFIG_SYS_IDE_MAXDEVICE 2 - -#define CONFIG_SYS_ATA_BASE_ADDR (CONFIG_SYS_MBAR2 + 0x800) -#define CONFIG_SYS_ATA_IDE0_OFFSET 0 - -#define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ -#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 - -#define CONFIG_SYS_MEMTEST_START 0x400 -#define CONFIG_SYS_MEMTEST_END 0x380000 - -#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ -#define CONFIG_SYS_FAST_CLK -#ifdef CONFIG_SYS_FAST_CLK -# define CONFIG_SYS_PLLCR 0x1243E054 -# define CONFIG_SYS_CLK 140000000 -#else -# define CONFIG_SYS_PLLCR 0x135a4140 -# define CONFIG_SYS_CLK 70000000 -#endif - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ -#define CONFIG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */ - -/* - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE 8 /* SDRAM size in MB */ - -#ifdef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_SYS_MONITOR_BASE 0x20000 -#else -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) -#endif - -#define CONFIG_SYS_MONITOR_LEN 0x40000 -#define CONFIG_SYS_MALLOC_LEN (256 << 10) -#define CONFIG_SYS_BOOTPARAMS_LEN (64*1024) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization ?? - */ -#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) -#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) - -/* FLASH organization */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 35 /* max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 - -#define CONFIG_SYS_FLASH_CFI 1 -#define CONFIG_FLASH_CFI_DRIVER 1 -#define CONFIG_SYS_FLASH_SIZE 0x200000 -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 16 - -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) -#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \ - CF_ADDRMASK(2) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ - CF_CACR_DBWE) - -/* Port configuration */ -#define CONFIG_SYS_FECI2C 0xF0 - -#define CONFIG_SYS_CS0_BASE 0xFFE00000 -#define CONFIG_SYS_CS0_MASK 0x001F0021 -#define CONFIG_SYS_CS0_CTRL 0x00001D80 - -/*----------------------------------------------------------------------- - * Port configuration - */ -#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ -#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */ -#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ -#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ -#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ -#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ -#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ - -#endif /* _M5253EVB_H */ |