diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/M5253DEMO.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/M5253DEMO.h | 244 |
1 files changed, 0 insertions, 244 deletions
diff --git a/qemu/roms/u-boot/include/configs/M5253DEMO.h b/qemu/roms/u-boot/include/configs/M5253DEMO.h deleted file mode 100644 index 3a1cbcae9..000000000 --- a/qemu/roms/u-boot/include/configs/M5253DEMO.h +++ /dev/null @@ -1,244 +0,0 @@ -/* Copyright (C) 2004-2007 Freescale Semiconductor, Inc. - * Hayden Fraser (Hayden.Fraser@freescale.com) - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _M5253DEMO_H -#define _M5253DEMO_H - -#define CONFIG_MCF52x2 /* define processor family */ -#define CONFIG_M5253 /* define processor type */ -#define CONFIG_M5253DEMO /* define board type */ - -#define CONFIG_MCFTMR - -#define CONFIG_MCFUART -#define CONFIG_SYS_UART_PORT (0) -#define CONFIG_BAUDRATE 115200 - -#undef CONFIG_WATCHDOG /* disable watchdog */ - -#define CONFIG_BOOTDELAY 5 - -/* Configuration for environment - * Environment is embedded in u-boot in the second sector of the flash - */ -#ifdef CONFIG_MONITOR_IS_IN_RAM -# define CONFIG_ENV_OFFSET 0x4000 -# define CONFIG_ENV_SECT_SIZE 0x1000 -# define CONFIG_ENV_IS_IN_FLASH 1 -#else -# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000) -# define CONFIG_ENV_SECT_SIZE 0x1000 -# define CONFIG_ENV_IS_IN_FLASH 1 -#endif - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_LOADB -#define CONFIG_CMD_LOADS -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_IDE -#define CONFIG_CMD_MEMORY -#define CONFIG_CMD_MISC -#define CONFIG_CMD_PING - -#ifdef CONFIG_CMD_IDE -/* ATA */ -# define CONFIG_DOS_PARTITION -# define CONFIG_MAC_PARTITION -# define CONFIG_IDE_RESET 1 -# define CONFIG_IDE_PREINIT 1 -# define CONFIG_ATAPI -# undef CONFIG_LBA48 - -# define CONFIG_SYS_IDE_MAXBUS 1 -# define CONFIG_SYS_IDE_MAXDEVICE 2 - -# define CONFIG_SYS_ATA_BASE_ADDR (CONFIG_SYS_MBAR2 + 0x800) -# define CONFIG_SYS_ATA_IDE0_OFFSET 0 - -# define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */ -# define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */ -# define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */ -# define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ -#endif - -#define CONFIG_DRIVER_DM9000 -#ifdef CONFIG_DRIVER_DM9000 -# define CONFIG_DM9000_BASE (CONFIG_SYS_CS1_BASE | 0x300) -# define DM9000_IO CONFIG_DM9000_BASE -# define DM9000_DATA (CONFIG_DM9000_BASE + 4) -# undef CONFIG_DM9000_DEBUG -# define CONFIG_DM9000_BYTE_SWAPPED - -# define CONFIG_OVERWRITE_ETHADDR_ONCE - -# define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ - "loadaddr=10000\0" \ - "u-boot=u-boot.bin\0" \ - "load=tftp ${loadaddr) ${u-boot}\0" \ - "upd=run load; run prog\0" \ - "prog=prot off 0xff800000 0xff82ffff;" \ - "era 0xff800000 0xff82ffff;" \ - "cp.b ${loadaddr} 0xff800000 ${filesize};" \ - "save\0" \ - "" -#endif - -#define CONFIG_HOSTNAME M5253DEMO - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 80000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000280 -#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR -#define CONFIG_SYS_I2C_PINMUX_REG (*(u32 *) (CONFIG_SYS_MBAR+0x19C)) -#define CONFIG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF) -#define CONFIG_SYS_I2C_PINMUX_SET (0) - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 - -#define CONFIG_SYS_MEMTEST_START 0x400 -#define CONFIG_SYS_MEMTEST_END 0x380000 - -#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ -#define CONFIG_SYS_FAST_CLK -#ifdef CONFIG_SYS_FAST_CLK -# define CONFIG_SYS_PLLCR 0x1243E054 -# define CONFIG_SYS_CLK 140000000 -#else -# define CONFIG_SYS_PLLCR 0x135a4140 -# define CONFIG_SYS_CLK 70000000 -#endif - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ -#define CONFIG_SYS_MBAR2 0x80000000 /* Module Base Addrs 2 */ - -/* - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ - -#ifdef CONFIG_MONITOR_IS_IN_RAM -# define CONFIG_SYS_MONITOR_BASE 0x20000 -#else -# define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) -#endif - -#define CONFIG_SYS_MONITOR_LEN 0x40000 -#define CONFIG_SYS_MALLOC_LEN (256 << 10) -#define CONFIG_SYS_BOOTPARAMS_LEN (64*1024) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization ?? - */ -#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) -#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) - -/* FLASH organization */ -#define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE) -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 2048 /* max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 - -#define FLASH_SST6401B 0x200 -#define SST_ID_xF6401B 0x236D236D - -#undef CONFIG_SYS_FLASH_CFI -#ifdef CONFIG_SYS_FLASH_CFI -/* - * Unable to use CFI driver, due to incompatible sector erase command by SST. - * Amd/Atmel use 0x30 for sector erase, SST use 0x50. - * 0x30 is block erase in SST - */ -# define CONFIG_FLASH_CFI_DRIVER 1 -# define CONFIG_SYS_FLASH_SIZE 0x800000 -# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -# define CONFIG_FLASH_CFI_LEGACY -#else -# define CONFIG_SYS_SST_SECT 2048 -# define CONFIG_SYS_SST_SECTSZ 0x1000 -# define CONFIG_SYS_FLASH_WRITE_TOUT 500 -#endif - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 16 - -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) -#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \ - CF_ADDRMASK(8) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ - CF_CACR_DBWE) - -/* Port configuration */ -#define CONFIG_SYS_FECI2C 0xF0 - -#define CONFIG_SYS_CS0_BASE 0xFF800000 -#define CONFIG_SYS_CS0_MASK 0x007F0021 -#define CONFIG_SYS_CS0_CTRL 0x00001D80 - -#define CONFIG_SYS_CS1_BASE 0xE0000000 -#define CONFIG_SYS_CS1_MASK 0x00000001 -#define CONFIG_SYS_CS1_CTRL 0x00003DD8 - -/*----------------------------------------------------------------------- - * Port configuration - */ -#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ -#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */ -#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ -#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ -#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ -#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ -#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ - -#endif /* _M5253DEMO_H */ |