summaryrefslogtreecommitdiffstats
path: root/qemu/roms/u-boot/include/configs/JSE.h
diff options
context:
space:
mode:
Diffstat (limited to 'qemu/roms/u-boot/include/configs/JSE.h')
-rw-r--r--qemu/roms/u-boot/include/configs/JSE.h276
1 files changed, 276 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/JSE.h b/qemu/roms/u-boot/include/configs/JSE.h
new file mode 100644
index 000000000..5cc25576a
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/JSE.h
@@ -0,0 +1,276 @@
+/*
+ * (C) Copyright 2003 Picture Elements, Inc.
+ * Stephen Williams <steve@icarus.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options for the JSE board
+ * (Theoretically easy to change, but the board is fixed.)
+ */
+
+#define CONFIG_JSE 1
+ /* JSE has a PPC405GPr */
+#define CONFIG_405GP 1
+ /* ... with a 33MHz OSC. connected to the SysCLK input */
+#define CONFIG_SYS_CLK_FREQ 33333333
+ /* ... with on-chip memory here (4KBytes) */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000
+ /* Do not set up locked dcache as init ram. */
+#undef CONFIG_SYS_INIT_DCACHE_CS
+
+#define CONFIG_SYS_TEXT_BASE 0xFFF80000
+
+ /* Map the SystemACE chip (CS#1) here. (Must be a multiple of 1Meg) */
+#define CONFIG_SYSTEMACE 1
+#define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
+#define CONFIG_SYS_SYSTEMACE_WIDTH 8
+#define CONFIG_DOS_PARTITION 1
+
+ /* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+ /* ... place INIT RAM in the OCM address */
+# define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR
+ /* ... give it the whole init ram */
+# define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE
+ /* ... Shave a bit off the end for global data */
+# define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+ /* ... and place the stack pointer at the top of what's left. */
+# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+ /* Enable board_pre_init function */
+#define CONFIG_BOARD_PRE_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
+ /* Disable post-clk setup init function */
+#undef CONFIG_BOARD_POSTCLK_INIT
+ /* Disable call to post_init_f: late init function. */
+#undef CONFIG_POST
+ /* Enable DRAM test. */
+#define CONFIG_SYS_DRAM_TEST 1
+ /* Enable misc_init_r function. */
+#define CONFIG_MISC_INIT_R 1
+
+ /* JSE has EEPROM chips that are good for environment. */
+#undef CONFIG_ENV_IS_IN_NVRAM
+#undef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_IS_IN_EEPROM 1
+#undef CONFIG_ENV_IS_NOWHERE
+
+ /* This is the 7bit address of the device, not including P. */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+ /* After the device address, need one more address byte. */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+ /* The EEPROM is 512 bytes. */
+#define CONFIG_SYS_EEPROM_SIZE 512
+ /* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
+ /* Put the environment in the second half. */
+#define CONFIG_ENV_OFFSET 0x00
+#define CONFIG_ENV_SIZE 512
+
+ /* The JSE connects UART1 to the console tap connector. */
+#define CONFIG_CONS_INDEX 2
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
+ /* Set console baudrate to 9600 */
+#define CONFIG_BAUDRATE 9600
+
+/*
+ * Configuration related to auto-boot.
+ *
+ * CONFIG_BOOTDELAY sets the delay (in seconds) that U-Boot will wait
+ * before resorting to autoboot. This value can be overridden by the
+ * bootdelay environment variable.
+ *
+ * CONFIG_AUTOBOOT_PROMPT is the string that U-Boot emits to warn the
+ * user that an autoboot will happen.
+ *
+ * CONFIG_BOOTCOMMAND is the sequence of commands that U-Boot will
+ * execute to boot the JSE. This loads the uimage and initrd.img files
+ * from CompactFlash into memory, then boots them from memory.
+ *
+ * CONFIG_BOOTARGS is the arguments passed to the Linux kernel to get
+ * it going on the JSE.
+ */
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_BOOTARGS "root=/dev/ram0 init=/linuxrc rw"
+#define CONFIG_BOOTCOMMAND "fatload ace 0 2000000 uimage; fatload ace 0 2100000 initrd.img; bootm 2000000 2100000"
+
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 1 /* PHY address */
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+
+
+ /* watchdog disabled */
+#undef CONFIG_WATCHDOG
+ /* SPD EEPROM (sdram speed config) disabled */
+#undef CONFIG_SPD_EEPROM
+#undef SPD_EEPROM_ADDRESS
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+/*
+ * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
+ * The Linux BASE_BAUD define should match this configuration.
+ * baseBaud = cpuClock/(uartDivisor*16)
+ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * set Linux BASE_BAUD to 403200.
+ */
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
+#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
+#define CONFIG_SYS_BASE_BAUD 691200
+
+/* The following table includes the supported baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#undef CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
+#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
+#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
+#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+
+/*-----------------------------------------------------------------------
+ * External peripheral base address
+ *-----------------------------------------------------------------------
+ */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
+
+#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000
+#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000
+#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFFF80000
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
+
+
+/* Configuration Port location */
+#define CONFIG_PORT_ADDR 0xF0000500
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+#endif /* __CONFIG_H */