diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/IDS8247.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/IDS8247.h | 462 |
1 files changed, 462 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/IDS8247.h b/qemu/roms/u-boot/include/configs/IDS8247.h new file mode 100644 index 000000000..8ccb0ff9d --- /dev/null +++ b/qemu/roms/u-boot/include/configs/IDS8247.h @@ -0,0 +1,462 @@ +/* + * (C) Copyright 2005 + * Heiko Schocher, DENX Software Engineering, <hs@denx.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8272_FAMILY 1 +#define CONFIG_IDS8247 1 +#define CPU_ID_STR "MPC8247" +#define CONFIG_CPM2 1 /* Has a CPM2 */ + +#define CONFIG_SYS_TEXT_BASE 0xfff00000 + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_BOOTCOUNT_LIMIT + +#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw " \ + "console=ttyS0,115200\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ + "rootpath=/opt/eldk/ppc_82xx\0" \ + "bootfile=/tftpboot/IDS8247/uImage\0" \ + "kernel_addr=ff800000\0" \ + "ramdisk_addr=ffa00000\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_MISC_INIT_R 1 + +/* enable I2C and select the hardware/software driver */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 400000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F +/* + * Software (bit-bang) I2C driver configuration + */ + +#define I2C_PORT 0 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00000080) +#define I2C_TRISTATE (iop->pdir &= ~0x00000080) +#define I2C_READ ((iop->pdat & 0x00000080) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00000080; \ + else iop->pdat &= ~0x00000080 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00000100; \ + else iop->pdat &= ~0x00000100 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#if 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +#define CONFIG_I2C_X +#endif + +/* + * select serial console configuration + * use the extern UART for the console + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +/* + * NS16550 Configuration + */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL + +#define CONFIG_SYS_NS16550_REG_SIZE 1 + +#define CONFIG_SYS_NS16550_CLK 14745600 + +#define CONFIG_SYS_UART_BASE 0xE0000000 +#define CONFIG_SYS_UART_SIZE 0x10000 + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_UART_BASE + 0x8000) + + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc@f0000000/serial8250@e0008000" + + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */ +#define CONFIG_ETHER_ON_FCC1 +#define FCC_ENET + +/* + * - Rx-CLK is CLK10 + * - Tx-CLK is CLK9 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK) +# define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK10|CMXFCR_TF1CS_CLK9) +# define CONFIG_SYS_CPMFCR_RAMTYPE 0 +# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#define CONFIG_8260_CLKIN 66666666 /* in Hz */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_TIMESTAMP /* Print image info with timestamp */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE + +#define CONFIG_RTC_PCF8563 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NFS +#define CONFIG_CMD_NAND +#define CONFIG_CMD_I2C +#define CONFIG_CMD_SNTP + + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CONFIG_SYS_FLASH_BANKS_LIST { 0xFF800000 } +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +/* What should the base address of the main FLASH be and how big is + * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/ids8247/config.mk + * The main FLASH is whichever is connected to *CS0. + */ +#define CONFIG_SYS_FLASH0_BASE 0xFFF00000 +#define CONFIG_SYS_FLASH0_SIZE 8 + +/* Flash bank size (for preliminary settings) + */ +#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +/* Environment in flash */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x60000) +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_ENV_SECT_SIZE 0x20000 + +/*----------------------------------------------------------------------- + * NAND-FLASH stuff + *----------------------------------------------------------------------- + */ +#if defined(CONFIG_CMD_NAND) + +#define CONFIG_SYS_NAND0_BASE 0xE1000000 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ + +#endif /* CONFIG_CMD_NAND */ + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CONFIG_SYS_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR. + */ +#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS01 | HRCW_BMS | HRCW_ISB100 | HRCW_APPC10 | HRCW_MODCK_H1000) + +/* no slaves so just fill with zeros */ +#define CONFIG_SYS_HRCW_SLAVE1 0 +#define CONFIG_SYS_HRCW_SLAVE2 0 +#define CONFIG_SYS_HRCW_SLAVE3 0 +#define CONFIG_SYS_HRCW_SLAVE4 0 +#define CONFIG_SYS_HRCW_SLAVE5 0 +#define CONFIG_SYS_HRCW_SLAVE6 0 +#define CONFIG_SYS_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CONFIG_SYS_IMMR 0xF0000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + * + * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ + +#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI) +#define CONFIG_SYS_HID0_FINAL 0 +#define CONFIG_SYS_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CONFIG_SYS_RMR 0 + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_BCR 0 + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_BCTLC01) + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + * Ensure DFBRG is Divide by 16 + */ +#define CONFIG_SYS_SCCR (0x00000028 | SCCR_DFBRG01) + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_RCCR 0 + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 16 bit FLASH + * 1 60x GPCM 8 bit NAND + * 2 60x SDRAM 32 bit SDRAM + * 3 60x GPCM 8 bit UART + * + */ + +#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ + +/* Minimum mask to separate preliminary + * address ranges for CS[0:2] + */ +#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (32<<20) /* less than 32 MB */ + +#define CONFIG_SYS_MPTPR 0x6600 + +/*----------------------------------------------------------------------------- + * Address for Mode Register Set (MRS) command + *----------------------------------------------------------------------------- + */ +#define CONFIG_SYS_MRS_OFFS 0x00000110 + + +/* Bank 0 - FLASH + */ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ + ORxG_SCY_6_CLK ) + +#if defined(CONFIG_CMD_NAND) +/* Bank 1 - NAND Flash +*/ +#define CONFIG_SYS_NAND_BASE CONFIG_SYS_NAND0_BASE +#define CONFIG_SYS_NAND_SIZE 0x8000 + +#define CONFIG_SYS_OR_TIMING_NAND 0x000036 + +#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_NAND_BASE & BRx_BA_MSK) | BRx_PS_8 | BRx_MS_GPCM_P | BRx_V ) +#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(CONFIG_SYS_NAND_SIZE) | CONFIG_SYS_OR_TIMING_NAND ) +#endif + +/* Bank 2 - 60x bus SDRAM + */ +#define CONFIG_SYS_PSRT 0x20 +#define CONFIG_SYS_LSRT 0x20 + +#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_32 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2 + + +/* SDRAM initialization values +*/ +#define CONFIG_SYS_OR2 ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A9 |\ + ORxS_NUMR_12) + +#define CONFIG_SYS_PSDMR (PSDMR_SDAM_A14_IS_A5 |\ + PSDMR_BSMA_A15_A17 |\ + PSDMR_SDA10_PBI0_A10 |\ + PSDMR_RFRC_5_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_BL |\ + PSDMR_LDOTOPRE_2C |\ + PSDMR_WRC_3C |\ + PSDMR_CL_3) + +/* Bank 3 - UART +*/ + +#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_UART_BASE & BRx_BA_MSK) | BRx_PS_8 | BRx_MS_GPCM_P | BRx_V ) +#define CONFIG_SYS_OR3_PRELIM (((-CONFIG_SYS_UART_SIZE) & ORxG_AM_MSK) | ORxG_CSNT | ORxG_SCY_1_CLK | ORxG_TRLX ) + +#endif /* __CONFIG_H */ |