summaryrefslogtreecommitdiffstats
path: root/qemu/roms/u-boot/include/configs/G2000.h
diff options
context:
space:
mode:
Diffstat (limited to 'qemu/roms/u-boot/include/configs/G2000.h')
-rw-r--r--qemu/roms/u-boot/include/configs/G2000.h383
1 files changed, 383 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/G2000.h b/qemu/roms/u-boot/include/configs/G2000.h
new file mode 100644
index 000000000..0c66092e0
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/G2000.h
@@ -0,0 +1,383 @@
+/*
+ * (C) Copyright 2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405EP 1 /* This is a PPC405 CPU */
+#define CONFIG_G2000 1 /* ...on a PLU405 board */
+
+#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
+
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+
+#if 0 /* test-only */
+#define CONFIG_BAUDRATE 115200
+#else
+#define CONFIG_BAUDRATE 9600
+#endif
+
+#define CONFIG_PREBOOT
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off\0" \
+ "addmisc=setenv bootargs ${bootargs} " \
+ "console=ttyS0,${baudrate} " \
+ "panic=1\0" \
+ "flash_nfs=run nfsargs addip addmisc;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip addmisc;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};" \
+ "run nfsargs addip addmisc;bootm\0" \
+ "rootpath=/opt/eldk/ppc_4xx\0" \
+ "bootfile=/tftpboot/g2000/pImage\0" \
+ "kernel_addr=ff800000\0" \
+ "ramdisk_addr=ff900000\0" \
+ "pciconfighost=yes\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run net_nfs"
+
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+
+#define CONFIG_PPC4xx_EMAC
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY1_ADDR 1 /* PHY address */
+
+#if 0 /* test-only */
+#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
+#endif
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_EEPROM
+
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#if 0 /* test-only */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+
+#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
+
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
+#define CONFIG_SYS_BASE_BAUD 691200
+
+/* The following table includes the supported baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ 57600, 115200, 230400, 460800, 921600 }
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+
+/*----------------------------------------------------------------------------*/
+/* adding Ethernet setting: FTS OUI 00:11:0B */
+/*----------------------------------------------------------------------------*/
+#define CONFIG_ETHADDR 00:11:0B:00:00:01
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:11:0B:00:00:02
+#define CONFIG_IPADDR 10.48.8.178
+#define CONFIG_IP1ADDR 10.48.8.188
+#define CONFIG_NETMASK 255.255.255.128
+#define CONFIG_SERVERIP 10.48.8.138
+
+/*-----------------------------------------------------------------------
+ * RTC stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_RTC_DS1337
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
+#if 0 /* test-only */
+/*-----------------------------------------------------------------------
+ * NAND-FLASH stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+
+#define CONFIG_SYS_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
+#define CONFIG_SYS_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
+#define CONFIG_SYS_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
+#define CONFIG_SYS_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
+
+#endif
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
+#define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
+
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#if 0 /* APC405 */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#undef CONFIG_SYS_FLASH_PROTECTION /* don't use hardware protection */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* test-only...*/
+#define CONFIG_SYS_FLASH_INCREMENT 0x01000000 /* test-only */
+#else /* G2000 */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#undef CONFIG_SYS_FLASH_PROTECTION /* don't use hardware protection */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* test-only...*/
+#define CONFIG_SYS_FLASH_INCREMENT 0x01000000 /* test-only */
+#endif
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#define CONFIG_SYS_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* ! second bank contains u-boot */
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_MONITOR_BASE 0xFFFC0000
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+
+/*-----------------------------------------------------------------------
+ * Environment Variable setup
+ */
+#if 1 /* test-only */
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/
+ /* total size of a CAT24WC16 is 2048 bytes */
+
+#else /* DEFAULT: environment in flash, using redundand flash sectors */
+
+#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+#define CONFIG_ENV_ADDR 0xFFFA0000 /* environment starts before u-boot */
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k bytes may be used for env vars*/
+
+#endif
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */
+/* CAT24WC08/16... */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Intel Strata Flash) initialization */
+#define CONFIG_SYS_EBC_PB0AP 0x92015480
+#define CONFIG_SYS_EBC_PB0CR 0xFF87A000 /* BAS=0xFF8,BS=08MB,BU=R/W,BW=16bit*/
+
+/* Memory Bank 1 ( Power TAU) initialization */
+/* #define CONFIG_SYS_EBC_PB1AP 0x04041000 */
+/* #define CONFIG_SYS_EBC_PB1CR 0xF0018000 */ /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CONFIG_SYS_EBC_PB1AP 0x00000000
+#define CONFIG_SYS_EBC_PB1CR 0x00000000
+
+/* Memory Bank 2 (Intel Flash) initialization */
+#define CONFIG_SYS_EBC_PB2AP 0x00000000
+#define CONFIG_SYS_EBC_PB2CR 0x00000000
+
+/* Memory Bank 3 (NAND) initialization */
+#define CONFIG_SYS_EBC_PB3AP 0x92015480
+#define CONFIG_SYS_EBC_PB3CR 0xF40B8000 /*addr 0xF40, BS=32M,BU=R/W, BW=8bit */
+
+/* Memory Bank 4 (FPGA regs) initialization */
+#define CONFIG_SYS_EBC_PB4AP 0x00000000
+#define CONFIG_SYS_EBC_PB4CR 0x00000000 /* leave it blank */
+
+#define CONFIG_SYS_NAND_BASE 0xF4000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CONFIG_SYS_TEMP_STACK_OCM 1
+
+/* On Chip Memory location */
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
+#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0] - External Bus Controller BLAST output
+ * GPIO0[1-9] - Instruction trace outputs
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ *
+ * following GPIO setting changed for G20000, 080304
+ */
+#define CONFIG_SYS_GPIO0_OSRL 0x40005555
+#define CONFIG_SYS_GPIO0_OSRH 0x40000110
+#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
+#define CONFIG_SYS_GPIO0_ISR1H 0x15555445
+#define CONFIG_SYS_GPIO0_TSRL 0x00000000
+#define CONFIG_SYS_GPIO0_TSRH 0x00000000
+#define CONFIG_SYS_GPIO0_TCR 0xF7FF8014
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#if 1
+#define PLLMR0_DEFAULT PLLMR0_266_66_33_33
+#define PLLMR1_DEFAULT PLLMR1_266_66_33_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
+#endif
+
+#endif /* __CONFIG_H */