diff options
Diffstat (limited to 'qemu/roms/u-boot/include/configs/CPCI405AB.h')
| -rw-r--r-- | qemu/roms/u-boot/include/configs/CPCI405AB.h | 373 |
1 files changed, 373 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/configs/CPCI405AB.h b/qemu/roms/u-boot/include/configs/CPCI405AB.h new file mode 100644 index 000000000..7d58e9d13 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/CPCI405AB.h @@ -0,0 +1,373 @@ +/* + * (C) Copyright 2001-2003 + * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_405GP 1 /* This is a PPC405 CPU */ +#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */ +#define CONFIG_CPCI405_VER2 1 /* ...version 2 */ +#define CONFIG_CPCI405AB 1 /* ...and special AB version */ + +#define CONFIG_SYS_TEXT_BASE 0xFFFC0000 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ + +#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */ + +#define CONFIG_BAUDRATE 9600 +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#undef CONFIG_BOOTARGS +#undef CONFIG_BOOTCOMMAND + +#define CONFIG_PREBOOT /* enable preboot variable */ + +#undef CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_PPC4xx_EMAC +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ + +#undef CONFIG_HAS_ETH1 + +#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PCI +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_IDE +#define CONFIG_CMD_FAT +#define CONFIG_CMD_ELF +#define CONFIG_CMD_DATE +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_BSP +#define CONFIG_CMD_EEPROM + + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_SUPPORT_VFAT + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ + +#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ +#define CONFIG_SYS_BASE_BAUD 691200 + +/* The following table includes the supported baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE \ + { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ + 57600, 115200, 230400, 460800, 921600 } + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CONFIG_CMDLINE_EDITING /* add command line history */ + +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ + +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT \ + "Press SPACE to abort autoboot in %d seconds\n", bootdelay +#undef CONFIG_AUTOBOOT_DELAY_STR +#define CONFIG_AUTOBOOT_STOP_STR " " + +#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ +#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + /* resource configuration */ + +#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ + +#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/ + +#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */ +#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ +#define CONFIG_SYS_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ +#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ +#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */ + +#define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */ + +/*----------------------------------------------------------------------- + * IDE/ATA stuff + *----------------------------------------------------------------------- + */ +#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ +#undef CONFIG_IDE_LED /* no led for ide supported */ +#define CONFIG_IDE_RESET 1 /* reset for ide supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ +#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ + +#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ + +#define CONFIG_PRAM 0 /* use pram variable to overwrite */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ +#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ +#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ +/* + * The following defines are added for buggy IOP480 byte interface. + * All other boards should use the standard values (CPCI405 etc.) + */ +#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ +#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ +#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +/*----------------------------------------------------------------------- + * I2C EEPROM (CAT24WC32) for environment + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 +#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* more than one eeprom used! */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ + /* 32 byte page write mode using*/ + /* last 5 bits of the address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +/* Use EEPROM for environment variables */ + +#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ +#define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ + /* total size of a CAT24WC32 is 4096 bytes */ + +#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */ +#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ +#define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/ + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */ + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + */ + +/* Memory Bank 0 (Flash Bank 0) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x92015480 +#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ + +/* Memory Bank 1 (Flash Bank 1) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x92015480 +#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */ + +/* Memory Bank 2 (CAN0, 1) initialization */ +#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ +#define CONFIG_SYS_LED_ADDR 0xF0000380 + +/* Memory Bank 3 (CompactFlash IDE) initialization */ +#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ + +/* Memory Bank 4 (NVRAM/RTC) initialization */ +/*#define CONFIG_SYS_EBC_PB4AP 0x01805280 / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1 */ +#define CONFIG_SYS_EBC_PB4AP 0x01805680 /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1 */ +#define CONFIG_SYS_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 5 (optional Quart) initialization */ +#define CONFIG_SYS_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/ +#define CONFIG_SYS_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 6 (FPGA internal) initialization */ +#define CONFIG_SYS_EBC_PB6AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB6CR 0xF041A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ +#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0400000 + +/*----------------------------------------------------------------------- + * FPGA stuff + */ +/* FPGA internal regs */ +#define CONFIG_SYS_FPGA_MODE 0x00 +#define CONFIG_SYS_FPGA_STATUS 0x02 +#define CONFIG_SYS_FPGA_TS 0x04 +#define CONFIG_SYS_FPGA_TS_LOW 0x06 +#define CONFIG_SYS_FPGA_TS_CAP0 0x10 +#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12 +#define CONFIG_SYS_FPGA_TS_CAP1 0x14 +#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16 +#define CONFIG_SYS_FPGA_TS_CAP2 0x18 +#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a +#define CONFIG_SYS_FPGA_TS_CAP3 0x1c +#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e + +/* FPGA Mode Reg */ +#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001 +#define CONFIG_SYS_FPGA_MODE_DUART_RESET 0x0002 +#define CONFIG_SYS_FPGA_MODE_ENABLE_OUTPUT 0x0004 /* only set on CPCI-405 Ver 3 */ +#define CONFIG_SYS_FPGA_MODE_1WIRE_DIR 0x0100 /* dir=1 -> output */ +#define CONFIG_SYS_FPGA_MODE_SIM_OK_DIR 0x0200 +#define CONFIG_SYS_FPGA_MODE_TESTRIG_FAIL_DIR 0x0400 +#define CONFIG_SYS_FPGA_MODE_1WIRE 0x1000 +#define CONFIG_SYS_FPGA_MODE_SIM_OK 0x2000 /* wired-or net from all devices */ +#define CONFIG_SYS_FPGA_MODE_TESTRIG_FAIL 0x4000 + +/* FPGA Status Reg */ +#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001 +#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002 +#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004 +#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008 +#define CONFIG_SYS_FPGA_STATUS_1WIRE 0x1000 +#define CONFIG_SYS_FPGA_STATUS_SIM_OK 0x2000 + +#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ +#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S30 */ + +/* FPGA program pin configuration */ +#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ +#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ +#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ +#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ +#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in data cache) + */ +#define CONFIG_SYS_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */ + +#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* use data cache */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#endif /* __CONFIG_H */ |