diff options
Diffstat (limited to 'qemu/roms/u-boot/include/commproc.h')
| -rw-r--r-- | qemu/roms/u-boot/include/commproc.h | 1459 |
1 files changed, 1459 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/include/commproc.h b/qemu/roms/u-boot/include/commproc.h new file mode 100644 index 000000000..29a3e61e8 --- /dev/null +++ b/qemu/roms/u-boot/include/commproc.h @@ -0,0 +1,1459 @@ +/* + * MPC8xx Communication Processor Module. + * Copyright (c) 1997 Dan Malek (dmalek@jlc.net) + * + * (C) Copyright 2000-2006 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * This file contains structures and information for the communication + * processor channels. Some CPM control and status is available + * throught the MPC8xx internal memory map. See immap.h for details. + * This file only contains what I need for the moment, not the total + * CPM capabilities. I (or someone else) will add definitions as they + * are needed. -- Dan + * + */ +#ifndef __CPM_8XX__ +#define __CPM_8XX__ + +#include <asm/8xx_immap.h> + +/* CPM Command register. +*/ +#define CPM_CR_RST ((ushort)0x8000) +#define CPM_CR_OPCODE ((ushort)0x0f00) +#define CPM_CR_CHAN ((ushort)0x00f0) +#define CPM_CR_FLG ((ushort)0x0001) + +/* Some commands (there are more...later) +*/ +#define CPM_CR_INIT_TRX ((ushort)0x0000) +#define CPM_CR_INIT_RX ((ushort)0x0001) +#define CPM_CR_INIT_TX ((ushort)0x0002) +#define CPM_CR_HUNT_MODE ((ushort)0x0003) +#define CPM_CR_STOP_TX ((ushort)0x0004) +#define CPM_CR_RESTART_TX ((ushort)0x0006) +#define CPM_CR_SET_GADDR ((ushort)0x0008) + +/* Channel numbers. +*/ +#define CPM_CR_CH_SCC1 ((ushort)0x0000) +#define CPM_CR_CH_I2C ((ushort)0x0001) /* I2C and IDMA1 */ +#define CPM_CR_CH_SCC2 ((ushort)0x0004) +#define CPM_CR_CH_SPI ((ushort)0x0005) /* SPI/IDMA2/Timers */ +#define CPM_CR_CH_SCC3 ((ushort)0x0008) +#define CPM_CR_CH_SMC1 ((ushort)0x0009) /* SMC1 / DSP1 */ +#define CPM_CR_CH_SCC4 ((ushort)0x000c) +#define CPM_CR_CH_SMC2 ((ushort)0x000d) /* SMC2 / DSP2 */ + +#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4)) + +/* + * DPRAM defines and allocation functions + */ + +/* The dual ported RAM is multi-functional. Some areas can be (and are + * being) used for microcode. There is an area that can only be used + * as data ram for buffer descriptors, which is all we use right now. + * Currently the first 512 and last 256 bytes are used for microcode. + */ +#ifdef CONFIG_SYS_ALLOC_DPRAM + +#define CPM_DATAONLY_BASE ((uint)0x0800) +#define CPM_DATAONLY_SIZE ((uint)0x0700) +#define CPM_DP_NOSPACE ((uint)0x7fffffff) + +#else + +#define CPM_SERIAL_BASE 0x0800 +#define CPM_I2C_BASE 0x0820 +#define CPM_SPI_BASE 0x0840 +#define CPM_FEC_BASE 0x0860 +#define CPM_SERIAL2_BASE 0x08E0 +#define CPM_SCC_BASE 0x0900 +#define CPM_POST_BASE 0x0980 +#define CPM_WLKBD_BASE 0x0a00 + +#endif + +#ifndef CONFIG_SYS_CPM_POST_WORD_ADDR +#define CPM_POST_WORD_ADDR 0x07FC +#else +#define CPM_POST_WORD_ADDR CONFIG_SYS_CPM_POST_WORD_ADDR +#endif + +#ifndef CONFIG_SYS_CPM_BOOTCOUNT_ADDR +#define CPM_BOOTCOUNT_ADDR (CPM_POST_WORD_ADDR - 2*sizeof(ulong)) +#else +#define CPM_BOOTCOUNT_ADDR CONFIG_SYS_CPM_BOOTCOUNT_ADDR +#endif + +#define BD_IIC_START ((uint) 0x0400) /* <- please use CPM_I2C_BASE !! */ + +/* Export the base address of the communication processor registers + * and dual port ram. + */ +extern cpm8xx_t *cpmp; /* Pointer to comm processor */ + +/* Buffer descriptors used by many of the CPM protocols. +*/ +typedef struct cpm_buf_desc { + ushort cbd_sc; /* Status and Control */ + ushort cbd_datlen; /* Data length in buffer */ + uint cbd_bufaddr; /* Buffer address in host memory */ +} cbd_t; + +#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */ +#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */ +#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */ +#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */ +#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */ +#define BD_SC_TC ((ushort)0x0400) /* Transmit CRC */ +#define BD_SC_CM ((ushort)0x0200) /* Continous mode */ +#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */ +#define BD_SC_P ((ushort)0x0100) /* xmt preamble */ +#define BD_SC_BR ((ushort)0x0020) /* Break received */ +#define BD_SC_FR ((ushort)0x0010) /* Framing error */ +#define BD_SC_PR ((ushort)0x0008) /* Parity error */ +#define BD_SC_OV ((ushort)0x0002) /* Overrun */ +#define BD_SC_CD ((ushort)0x0001) /* Carrier Detect lost */ + +/* Parameter RAM offsets. +*/ +#define PROFF_SCC1 ((uint)0x0000) +#define PROFF_IIC ((uint)0x0080) +#define PROFF_REVNUM ((uint)0x00b0) +#define PROFF_SCC2 ((uint)0x0100) +#define PROFF_SPI ((uint)0x0180) +#define PROFF_SCC3 ((uint)0x0200) +#define PROFF_SMC1 ((uint)0x0280) +#define PROFF_SCC4 ((uint)0x0300) +#define PROFF_SMC2 ((uint)0x0380) + +/* Define enough so I can at least use the serial port as a UART. + */ +typedef struct smc_uart { + ushort smc_rbase; /* Rx Buffer descriptor base address */ + ushort smc_tbase; /* Tx Buffer descriptor base address */ + u_char smc_rfcr; /* Rx function code */ + u_char smc_tfcr; /* Tx function code */ + ushort smc_mrblr; /* Max receive buffer length */ + uint smc_rstate; /* Internal */ + uint smc_idp; /* Internal */ + ushort smc_rbptr; /* Internal */ + ushort smc_ibc; /* Internal */ + uint smc_rxtmp; /* Internal */ + uint smc_tstate; /* Internal */ + uint smc_tdp; /* Internal */ + ushort smc_tbptr; /* Internal */ + ushort smc_tbc; /* Internal */ + uint smc_txtmp; /* Internal */ + ushort smc_maxidl; /* Maximum idle characters */ + ushort smc_tmpidl; /* Temporary idle counter */ + ushort smc_brklen; /* Last received break length */ + ushort smc_brkec; /* rcv'd break condition counter */ + ushort smc_brkcr; /* xmt break count register */ + ushort smc_rmask; /* Temporary bit mask */ + u_char res1[8]; + ushort smc_rpbase; /* Relocation pointer */ +} smc_uart_t; + +/* Function code bits. +*/ +#define SMC_EB ((u_char)0x10) /* Set big endian byte order */ + +/* SMC uart mode register. +*/ +#define SMCMR_REN ((ushort)0x0001) +#define SMCMR_TEN ((ushort)0x0002) +#define SMCMR_DM ((ushort)0x000c) +#define SMCMR_SM_GCI ((ushort)0x0000) +#define SMCMR_SM_UART ((ushort)0x0020) +#define SMCMR_SM_TRANS ((ushort)0x0030) +#define SMCMR_SM_MASK ((ushort)0x0030) +#define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */ +#define SMCMR_REVD SMCMR_PM_EVEN +#define SMCMR_PEN ((ushort)0x0200) /* Parity enable */ +#define SMCMR_BS SMCMR_PEN +#define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */ +#define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */ +#define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK) + +/* SMC2 as Centronics parallel printer. It is half duplex, in that + * it can only receive or transmit. The parameter ram values for + * each direction are either unique or properly overlap, so we can + * include them in one structure. + */ +typedef struct smc_centronics { + ushort scent_rbase; + ushort scent_tbase; + u_char scent_cfcr; + u_char scent_smask; + ushort scent_mrblr; + uint scent_rstate; + uint scent_r_ptr; + ushort scent_rbptr; + ushort scent_r_cnt; + uint scent_rtemp; + uint scent_tstate; + uint scent_t_ptr; + ushort scent_tbptr; + ushort scent_t_cnt; + uint scent_ttemp; + ushort scent_max_sl; + ushort scent_sl_cnt; + ushort scent_character1; + ushort scent_character2; + ushort scent_character3; + ushort scent_character4; + ushort scent_character5; + ushort scent_character6; + ushort scent_character7; + ushort scent_character8; + ushort scent_rccm; + ushort scent_rccr; +} smc_cent_t; + +/* Centronics Status Mask Register. +*/ +#define SMC_CENT_F ((u_char)0x08) +#define SMC_CENT_PE ((u_char)0x04) +#define SMC_CENT_S ((u_char)0x02) + +/* SMC Event and Mask register. +*/ +#define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */ +#define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */ +#define SMCM_TXE ((unsigned char)0x10) /* When in Transparent Mode */ +#define SMCM_BSY ((unsigned char)0x04) +#define SMCM_TX ((unsigned char)0x02) +#define SMCM_RX ((unsigned char)0x01) + +/* Baud rate generators. +*/ +#define CPM_BRG_RST ((uint)0x00020000) +#define CPM_BRG_EN ((uint)0x00010000) +#define CPM_BRG_EXTC_INT ((uint)0x00000000) +#define CPM_BRG_EXTC_CLK2 ((uint)0x00004000) +#define CPM_BRG_EXTC_CLK6 ((uint)0x00008000) +#define CPM_BRG_ATB ((uint)0x00002000) +#define CPM_BRG_CD_MASK ((uint)0x00001ffe) +#define CPM_BRG_DIV16 ((uint)0x00000001) + +/* SI Clock Route Register +*/ +#define SICR_RCLK_SCC1_BRG1 ((uint)0x00000000) +#define SICR_TCLK_SCC1_BRG1 ((uint)0x00000000) +#define SICR_RCLK_SCC2_BRG2 ((uint)0x00000800) +#define SICR_TCLK_SCC2_BRG2 ((uint)0x00000100) +#define SICR_RCLK_SCC3_BRG3 ((uint)0x00100000) +#define SICR_TCLK_SCC3_BRG3 ((uint)0x00020000) +#define SICR_RCLK_SCC4_BRG4 ((uint)0x18000000) +#define SICR_TCLK_SCC4_BRG4 ((uint)0x03000000) + +/* SCCs. +*/ +#define SCC_GSMRH_IRP ((uint)0x00040000) +#define SCC_GSMRH_GDE ((uint)0x00010000) +#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000) +#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000) +#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000) +#define SCC_GSMRH_REVD ((uint)0x00002000) +#define SCC_GSMRH_TRX ((uint)0x00001000) +#define SCC_GSMRH_TTX ((uint)0x00000800) +#define SCC_GSMRH_CDP ((uint)0x00000400) +#define SCC_GSMRH_CTSP ((uint)0x00000200) +#define SCC_GSMRH_CDS ((uint)0x00000100) +#define SCC_GSMRH_CTSS ((uint)0x00000080) +#define SCC_GSMRH_TFL ((uint)0x00000040) +#define SCC_GSMRH_RFW ((uint)0x00000020) +#define SCC_GSMRH_TXSY ((uint)0x00000010) +#define SCC_GSMRH_SYNL16 ((uint)0x0000000c) +#define SCC_GSMRH_SYNL8 ((uint)0x00000008) +#define SCC_GSMRH_SYNL4 ((uint)0x00000004) +#define SCC_GSMRH_RTSM ((uint)0x00000002) +#define SCC_GSMRH_RSYN ((uint)0x00000001) + +#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */ +#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000) +#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000) +#define SCC_GSMRL_EDGE_POS ((uint)0x20000000) +#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000) +#define SCC_GSMRL_TCI ((uint)0x10000000) +#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000) +#define SCC_GSMRL_TSNC_4 ((uint)0x08000000) +#define SCC_GSMRL_TSNC_14 ((uint)0x04000000) +#define SCC_GSMRL_TSNC_INF ((uint)0x00000000) +#define SCC_GSMRL_RINV ((uint)0x02000000) +#define SCC_GSMRL_TINV ((uint)0x01000000) +#define SCC_GSMRL_TPL_128 ((uint)0x00c00000) +#define SCC_GSMRL_TPL_64 ((uint)0x00a00000) +#define SCC_GSMRL_TPL_48 ((uint)0x00800000) +#define SCC_GSMRL_TPL_32 ((uint)0x00600000) +#define SCC_GSMRL_TPL_16 ((uint)0x00400000) +#define SCC_GSMRL_TPL_8 ((uint)0x00200000) +#define SCC_GSMRL_TPL_NONE ((uint)0x00000000) +#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000) +#define SCC_GSMRL_TPP_01 ((uint)0x00100000) +#define SCC_GSMRL_TPP_10 ((uint)0x00080000) +#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000) +#define SCC_GSMRL_TEND ((uint)0x00040000) +#define SCC_GSMRL_TDCR_32 ((uint)0x00030000) +#define SCC_GSMRL_TDCR_16 ((uint)0x00020000) +#define SCC_GSMRL_TDCR_8 ((uint)0x00010000) +#define SCC_GSMRL_TDCR_1 ((uint)0x00000000) +#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000) +#define SCC_GSMRL_RDCR_16 ((uint)0x00008000) +#define SCC_GSMRL_RDCR_8 ((uint)0x00004000) +#define SCC_GSMRL_RDCR_1 ((uint)0x00000000) +#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000) +#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000) +#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000) +#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800) +#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000) +#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600) +#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400) +#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200) +#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100) +#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000) +#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */ +#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080) +#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040) +#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000) +#define SCC_GSMRL_ENR ((uint)0x00000020) +#define SCC_GSMRL_ENT ((uint)0x00000010) +#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c) +#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009) +#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008) +#define SCC_GSMRL_MODE_V14 ((uint)0x00000007) +#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006) +#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005) +#define SCC_GSMRL_MODE_UART ((uint)0x00000004) +#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003) +#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002) +#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000) + +#define SCC_TODR_TOD ((ushort)0x8000) + +/* SCC Event and Mask register. +*/ +#define SCCM_TXE ((unsigned char)0x10) +#define SCCM_BSY ((unsigned char)0x04) +#define SCCM_TX ((unsigned char)0x02) +#define SCCM_RX ((unsigned char)0x01) + +typedef struct scc_param { + ushort scc_rbase; /* Rx Buffer descriptor base address */ + ushort scc_tbase; /* Tx Buffer descriptor base address */ + u_char scc_rfcr; /* Rx function code */ + u_char scc_tfcr; /* Tx function code */ + ushort scc_mrblr; /* Max receive buffer length */ + uint scc_rstate; /* Internal */ + uint scc_idp; /* Internal */ + ushort scc_rbptr; /* Internal */ + ushort scc_ibc; /* Internal */ + uint scc_rxtmp; /* Internal */ + uint scc_tstate; /* Internal */ + uint scc_tdp; /* Internal */ + ushort scc_tbptr; /* Internal */ + ushort scc_tbc; /* Internal */ + uint scc_txtmp; /* Internal */ + uint scc_rcrc; /* Internal */ + uint scc_tcrc; /* Internal */ +} sccp_t; + +/* Function code bits. +*/ +#define SCC_EB ((u_char)0x10) /* Set big endian byte order */ + +/* CPM Ethernet through SCCx. + */ +typedef struct scc_enet { + sccp_t sen_genscc; + uint sen_cpres; /* Preset CRC */ + uint sen_cmask; /* Constant mask for CRC */ + uint sen_crcec; /* CRC Error counter */ + uint sen_alec; /* alignment error counter */ + uint sen_disfc; /* discard frame counter */ + ushort sen_pads; /* Tx short frame pad character */ + ushort sen_retlim; /* Retry limit threshold */ + ushort sen_retcnt; /* Retry limit counter */ + ushort sen_maxflr; /* maximum frame length register */ + ushort sen_minflr; /* minimum frame length register */ + ushort sen_maxd1; /* maximum DMA1 length */ + ushort sen_maxd2; /* maximum DMA2 length */ + ushort sen_maxd; /* Rx max DMA */ + ushort sen_dmacnt; /* Rx DMA counter */ + ushort sen_maxb; /* Max BD byte count */ + ushort sen_gaddr1; /* Group address filter */ + ushort sen_gaddr2; + ushort sen_gaddr3; + ushort sen_gaddr4; + uint sen_tbuf0data0; /* Save area 0 - current frame */ + uint sen_tbuf0data1; /* Save area 1 - current frame */ + uint sen_tbuf0rba; /* Internal */ + uint sen_tbuf0crc; /* Internal */ + ushort sen_tbuf0bcnt; /* Internal */ + ushort sen_paddrh; /* physical address (MSB) */ + ushort sen_paddrm; + ushort sen_paddrl; /* physical address (LSB) */ + ushort sen_pper; /* persistence */ + ushort sen_rfbdptr; /* Rx first BD pointer */ + ushort sen_tfbdptr; /* Tx first BD pointer */ + ushort sen_tlbdptr; /* Tx last BD pointer */ + uint sen_tbuf1data0; /* Save area 0 - current frame */ + uint sen_tbuf1data1; /* Save area 1 - current frame */ + uint sen_tbuf1rba; /* Internal */ + uint sen_tbuf1crc; /* Internal */ + ushort sen_tbuf1bcnt; /* Internal */ + ushort sen_txlen; /* Tx Frame length counter */ + ushort sen_iaddr1; /* Individual address filter */ + ushort sen_iaddr2; + ushort sen_iaddr3; + ushort sen_iaddr4; + ushort sen_boffcnt; /* Backoff counter */ + + /* NOTE: Some versions of the manual have the following items + * incorrectly documented. Below is the proper order. + */ + ushort sen_taddrh; /* temp address (MSB) */ + ushort sen_taddrm; + ushort sen_taddrl; /* temp address (LSB) */ +} scc_enet_t; + +/********************************************************************** + * + * Board specific configuration settings. + * + * Please note that we use the presence of a #define SCC_ENET and/or + * #define FEC_ENET to enable the SCC resp. FEC ethernet drivers. + **********************************************************************/ + +/*** BSEIP **********************************************************/ + +#ifdef CONFIG_BSEIP +/* This ENET stuff is for the MPC823 with ethernet on SCC2. + * This is unique to the BSE ip-Engine board. + */ +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 +#define PA_ENET_RXD ((ushort)0x0004) +#define PA_ENET_TXD ((ushort)0x0008) +#define PA_ENET_TCLK ((ushort)0x0100) +#define PA_ENET_RCLK ((ushort)0x0200) +#define PB_ENET_TENA ((uint)0x00002000) +#define PC_ENET_CLSN ((ushort)0x0040) +#define PC_ENET_RENA ((ushort)0x0080) + +/* BSE uses port B and C bits for PHY control also. +*/ +#define PB_BSE_POWERUP ((uint)0x00000004) +#define PB_BSE_FDXDIS ((uint)0x00008000) +#define PC_BSE_LOOPBACK ((ushort)0x0800) + +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00002c00) +#endif /* CONFIG_BSEIP */ + +/*** BSEIP **********************************************************/ + +#ifdef CONFIG_FLAGADM +/* Enet configuration for the FLAGADM */ +/* Enet on SCC2 */ + +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 +#define PA_ENET_RXD ((ushort)0x0004) +#define PA_ENET_TXD ((ushort)0x0008) +#define PA_ENET_TCLK ((ushort)0x0100) +#define PA_ENET_RCLK ((ushort)0x0400) +#define PB_ENET_TENA ((uint)0x00002000) +#define PC_ENET_CLSN ((ushort)0x0040) +#define PC_ENET_RENA ((ushort)0x0080) + +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00003400) +#endif /* CONFIG_FLAGADM */ + +/*** ELPT860 *********************************************************/ + +#ifdef CONFIG_ELPT860 +/* Bits in parallel I/O port registers that have to be set/cleared + * to configure the pins for SCC1 use. + */ +# define PROFF_ENET PROFF_SCC1 +# define CPM_CR_ENET CPM_CR_CH_SCC1 +# define SCC_ENET 0 + +# define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */ +# define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */ +# define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ +# define PA_ENET_TCLK ((ushort)0x0200) /* PA 6 */ + +# define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */ +# define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */ +# define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */ + +/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK1) to + * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero. + */ +# define SICR_ENET_MASK ((uint)0x000000FF) +# define SICR_ENET_CLKRT ((uint)0x00000025) +#endif /* CONFIG_ELPT860 */ + +/*** ESTEEM 192E **************************************************/ +#ifdef CONFIG_ESTEEM192E +/* ESTEEM192E + * This ENET stuff is for the MPC850 with ethernet on SCC2. This + * is very similar to the RPX-Lite configuration. + * Note TENA , LOOPBACK , FDPLEX_DIS on Port B. + */ + +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 + +#define PA_ENET_RXD ((ushort)0x0004) +#define PA_ENET_TXD ((ushort)0x0008) +#define PA_ENET_TCLK ((ushort)0x0200) +#define PA_ENET_RCLK ((ushort)0x0800) +#define PB_ENET_TENA ((uint)0x00002000) +#define PC_ENET_CLSN ((ushort)0x0040) +#define PC_ENET_RENA ((ushort)0x0080) + +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00003d00) + +#define PB_ENET_LOOPBACK ((uint)0x00004000) +#define PB_ENET_FDPLEX_DIS ((uint)0x00008000) + +#endif + +/*** FADS860T********************************************************/ + +#if defined(CONFIG_FADS) && defined(CONFIG_MPC86x) +/* + * This ENET stuff is for the MPC86xFADS/MPC8xxADS with ethernet on SCC1. + */ +#ifdef CONFIG_SCC1_ENET + +#define SCC_ENET 0 + +#define PROFF_ENET PROFF_SCC1 +#define CPM_CR_ENET CPM_CR_CH_SCC1 + +#define PA_ENET_RXD ((ushort)0x0001) +#define PA_ENET_TXD ((ushort)0x0002) +#define PA_ENET_TCLK ((ushort)0x0100) +#define PA_ENET_RCLK ((ushort)0x0200) + +#define PB_ENET_TENA ((uint)0x00001000) + +#define PC_ENET_CLSN ((ushort)0x0010) +#define PC_ENET_RENA ((ushort)0x0020) + +#define SICR_ENET_MASK ((uint)0x000000ff) +#define SICR_ENET_CLKRT ((uint)0x0000002c) + +#endif /* CONFIG_SCC1_ETHERNET */ + +/* + * This ENET stuff is for the MPC860TFADS/MPC86xADS/MPC885ADS + * with ethernet on FEC. + */ + +#ifdef CONFIG_FEC_ENET +#define FEC_ENET /* Use FEC for Ethernet */ +#endif /* CONFIG_FEC_ENET */ + +#endif /* CONFIG_FADS && CONFIG_MPC86x */ + +/*** FPS850L, FPS860L ************************************************/ + +#if defined(CONFIG_FPS850L) || defined(CONFIG_FPS860L) +/* Bits in parallel I/O port registers that have to be set/cleared + * to configure the pins for SCC2 use. + */ +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 +#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ +#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ +#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ +#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ + +#define PC_ENET_TENA ((ushort)0x0002) /* PC 14 */ +#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ +#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ + +/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to + * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. + */ +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00002600) +#endif /* CONFIG_FPS850L, CONFIG_FPS860L */ + +/*** GEN860T **********************************************************/ +#if defined(CONFIG_GEN860T) +#undef SCC_ENET +#define FEC_ENET + +#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ +#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ +#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ +#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ +#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ +#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ +#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ +#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ +#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ +#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ +#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ +#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ +#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ +#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3-15 */ +#endif /* CONFIG_GEN860T */ + +/*** HERMES-PRO ******************************************************/ + +/* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */ + +#ifdef CONFIG_HERMES + +#define FEC_ENET /* use FEC for EThernet */ +#undef SCC_ENET + + +#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ +#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ +#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ +#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ +#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ +#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ +#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ +#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ +#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ +#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ +#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ +#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ +#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ + +#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ + +#endif /* CONFIG_HERMES */ + +/*** ICU862 **********************************************************/ + +#if defined(CONFIG_ICU862) + +#ifdef CONFIG_FEC_ENET +#define FEC_ENET /* use FEC for EThernet */ +#endif /* CONFIG_FEC_ETHERNET */ + +#endif /* CONFIG_ICU862 */ + +/*** IP860 **********************************************************/ + +#if defined(CONFIG_IP860) +/* Bits in parallel I/O port registers that have to be set/cleared + * to configure the pins for SCC1 use. + */ +#define PROFF_ENET PROFF_SCC1 +#define CPM_CR_ENET CPM_CR_CH_SCC1 +#define SCC_ENET 0 +#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */ +#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */ +#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ +#define PA_ENET_TCLK ((ushort)0x0100) /* PA 7 */ + +#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */ +#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */ +#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */ + +#define PB_ENET_RESET (uint)0x00000008 /* PB 28 */ +#define PB_ENET_JABD (uint)0x00000004 /* PB 29 */ + +/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to + * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero. + */ +#define SICR_ENET_MASK ((uint)0x000000ff) +#define SICR_ENET_CLKRT ((uint)0x0000002C) +#endif /* CONFIG_IP860 */ + +/*** IVMS8 **********************************************************/ + +/* The IVMS8 uses the FEC on a MPC860T for Ethernet */ + +#if defined(CONFIG_IVMS8) || defined(CONFIG_IVML24) + +#define FEC_ENET /* use FEC for EThernet */ +#undef SCC_ENET + +#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */ + +#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */ + +#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ +#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ +#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ +#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ +#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ +#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ +#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ +#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ +#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ +#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ +#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ +#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ +#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ + +#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ + +#endif /* CONFIG_IVMS8, CONFIG_IVML24 */ + +/*** KUP4K, KUP4X ****************************************************/ +/* The KUP4 boards uses the FEC on a MPC8xx for Ethernet */ + +#if defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X) + +#define FEC_ENET /* use FEC for EThernet */ +#undef SCC_ENET + +#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */ + +#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */ + +#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ +#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ +#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ +#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ +#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ +#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ +#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ +#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ +#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ +#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ +#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ +#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ +#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ + +#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ + +#endif /* CONFIG_KUP4K */ + +/*** LWMON **********************************************************/ + +#if defined(CONFIG_LWMON) +/* Bits in parallel I/O port registers that have to be set/cleared + * to configure the pins for SCC2 use. + */ +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 +#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ +#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ +#define PA_ENET_RCLK ((ushort)0x0800) /* PA 4 */ +#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ + +#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ + +#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ +#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ + +/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK4) to + * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. + */ +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00003E00) +#endif /* CONFIG_LWMON */ + +/*** KM8XX *********************************************************/ + +/* The KM8XX Service Module uses SCC3 for Ethernet */ + +#ifdef CONFIG_KM8XX +#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */ +#define CPM_CR_ENET CPM_CR_CH_SCC3 +#define SCC_ENET 2 +#define PA_ENET_RXD ((ushort)0x0010) /* PA 11 */ +#define PA_ENET_TXD ((ushort)0x0020) /* PA 10 */ +#define PA_ENET_RCLK ((ushort)0x1000) /* PA 3 CLK 5 */ +#define PA_ENET_TCLK ((ushort)0x2000) /* PA 2 CLK 6 */ + +#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */ + +#define PC_ENET_RENA ((ushort)0x0200) /* PC 6 */ +#define PC_ENET_CLSN ((ushort)0x0100) /* PC 7 */ + +/* Control bits in the SICR to route TCLK (CLK6) and RCLK (CLK5) to + * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero. + */ +#define SICR_ENET_MASK ((uint)0x00FF0000) +#define SICR_ENET_CLKRT ((uint)0x00250000) +#endif /* CONFIG_KM8XX */ + + +/*** MHPC ********************************************************/ + +#if defined(CONFIG_MHPC) +/* This ENET stuff is for the MHPC with ethernet on SCC2. + * Note TENA is on Port B. + */ +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 +#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ +#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ +#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ +#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ +#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ +#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ +#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ + +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */ +#endif /* CONFIG_MHPC */ + +/*** NETVIA *******************************************************/ + +/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */ +#if ( defined CONFIG_SVM_SC8xx ) +# ifndef CONFIG_FEC_ENET + +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 + + /* Bits in parallel I/O port registers that have to be set/cleared + * * * * to configure the pins for SCC2 use. + * * * */ +#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ +#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ +#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */ +#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ + +#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ + +#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ +#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ +/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to + * * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. + * * * */ +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00003700) + +# else /* Use FEC for Fast Ethernet */ + +#undef SCC_ENET +#define FEC_ENET + +#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ +#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ +#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ +#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ +#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ +#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ +#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ +#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ +#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ +#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ +#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ +#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ +#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ + +#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ + +# endif /* CONFIG_FEC_ENET */ +#endif /* CONFIG_SVM_SC8xx */ + + +#if defined(CONFIG_NETVIA) +/* Bits in parallel I/O port registers that have to be set/cleared + * to configure the pins for SCC2 use. + */ +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 +#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ +#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ +#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ +#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ + +#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1 +# define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */ +#elif CONFIG_NETVIA_VERSION >= 2 +# define PC_ENET_PDN ((ushort)0x0008) /* PC 12 */ +#endif + +#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */ + +#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ +#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ + +/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to + * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. + */ +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00002f00) + +#endif /* CONFIG_NETVIA */ + +/*** QS850/QS823 ***************************************************/ + +#if defined(CONFIG_QS850) || defined(CONFIG_QS823) +#undef FEC_ENET /* Don't use FEC for EThernet */ + +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 + +#define PA_ENET_RXD ((ushort)0x0004) /* RXD on PA13 (Pin D9) */ +#define PA_ENET_TXD ((ushort)0x0008) /* TXD on PA12 (Pin D7) */ +#define PC_ENET_RENA ((ushort)0x0080) /* RENA on PC8 (Pin D12) */ +#define PC_ENET_CLSN ((ushort)0x0040) /* CLSN on PC9 (Pin C12) */ +#define PA_ENET_TCLK ((ushort)0x0200) /* TCLK on PA6 (Pin D8) */ +#define PA_ENET_RCLK ((ushort)0x0800) /* RCLK on PA4 (Pin D10) */ +#define PB_ENET_TENA ((uint)0x00002000) /* TENA on PB18 (Pin D11) */ +#define PC_ENET_LBK ((ushort)0x0010) /* Loopback control on PC11 (Pin B14) */ +#define PC_ENET_LI ((ushort)0x0020) /* Link Integrity control PC10 (A15) */ +#define PC_ENET_SQE ((ushort)0x0100) /* SQE Disable control PC7 (B15) */ + +/* SCC2 TXCLK from CLK2 + * SCC2 RXCLK from CLK4 + * SCC2 Connected to NMSI */ +#define SICR_ENET_MASK ((uint)0x00007F00) +#define SICR_ENET_CLKRT ((uint)0x00003D00) + +#endif /* CONFIG_QS850/QS823 */ + +/*** QS860T ***************************************************/ + +#ifdef CONFIG_QS860T +#ifdef CONFIG_FEC_ENET +#define FEC_ENET /* use FEC for EThernet */ +#endif /* CONFIG_FEC_ETHERNET */ + +/* This ENET stuff is for GTH 10 Mbit ( SCC ) */ +#define PROFF_ENET PROFF_SCC1 +#define CPM_CR_ENET CPM_CR_CH_SCC1 +#define SCC_ENET 0 + +#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */ +#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */ +#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */ +#define PA_ENET_RCLK ((ushort)0x0200) /* PA6 */ +#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */ +#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */ +#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */ + +#define SICR_ENET_MASK ((uint)0x000000ff) +/* RCLK PA4 -->CLK4, TCLK PA6 -->CLK2 */ +#define SICR_ENET_CLKRT ((uint)0x0000003D) + +#endif /* CONFIG_QS860T */ + +/*** RPXLITE ********************************************************/ + +#ifdef CONFIG_RPXLITE +/* This ENET stuff is for the MPC850 with ethernet on SCC2. Some of + * this may be unique to the RPX-Lite configuration. + * Note TENA is on Port B. + */ +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 +#define PA_ENET_RXD ((ushort)0x0004) +#define PA_ENET_TXD ((ushort)0x0008) +#define PA_ENET_TCLK ((ushort)0x0200) +#define PA_ENET_RCLK ((ushort)0x0800) +#if defined(CONFIG_RMU) +#define PC_ENET_TENA ((uint)0x00000002) /* PC14 */ +#else +#define PB_ENET_TENA ((uint)0x00002000) +#endif +#define PC_ENET_CLSN ((ushort)0x0040) +#define PC_ENET_RENA ((ushort)0x0080) + +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00003d00) +#endif /* CONFIG_RPXLITE */ + +/*** SM850 *********************************************************/ + +/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */ + +#ifdef CONFIG_SM850 +#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */ +#define CPM_CR_ENET CPM_CR_CH_SCC3 +#define SCC_ENET 2 +#define PB_ENET_RXD ((uint)0x00000004) /* PB 29 */ +#define PB_ENET_TXD ((uint)0x00000002) /* PB 30 */ +#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ +#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ + +#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */ +#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */ + +#define PC_ENET_RENA ((ushort)0x0800) /* PC 4 */ +#define PC_ENET_CLSN ((ushort)0x0400) /* PC 5 */ + +/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to + * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero. + */ +#define SICR_ENET_MASK ((uint)0x00FF0000) +#define SICR_ENET_CLKRT ((uint)0x00260000) +#endif /* CONFIG_SM850 */ + +/*** SPD823TS ******************************************************/ + +#ifdef CONFIG_SPD823TS +/* Bits in parallel I/O port registers that have to be set/cleared + * to configure the pins for SCC2 use. + */ +#define PROFF_ENET PROFF_SCC2 /* Ethernet on SCC2 */ +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 +#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */ +#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */ +#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ +#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ +#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ +#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ + +#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ + +#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ +#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ +#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */ + +/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to + * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. + */ +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00002E00) +#endif /* CONFIG_SPD823TS */ + +/*** SXNI855T ******************************************************/ + +#if defined(CONFIG_SXNI855T) + +#ifdef CONFIG_FEC_ENET +#define FEC_ENET /* use FEC for Ethernet */ +#endif /* CONFIG_FEC_ETHERNET */ + +#endif /* CONFIG_SXNI855T */ + +/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/ + +#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \ + defined(CONFIG_R360MPI) || defined(CONFIG_RBC823) || \ + defined(CONFIG_RRVISION)|| defined(CONFIG_TQM823L) || \ + defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \ + defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) || \ + defined(CONFIG_RRVISION)|| defined(CONFIG_VIRTLAB2) + +/* Bits in parallel I/O port registers that have to be set/cleared + * to configure the pins for SCC2 use. + */ +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#if (!defined(CONFIG_TK885D)) /* TK885D does not use SCC Ethernet */ +#define SCC_ENET 1 +#endif +#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ +#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ +#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ +#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ + +#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ + +#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ +#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ +#if defined(CONFIG_R360MPI) +#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */ +#endif /* CONFIG_R360MPI */ + +/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to + * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. + */ +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00002600) + +# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */ +#define FEC_ENET +# endif /* CONFIG_FEC_ENET */ + +#endif /* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */ + +/*** TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M *********************/ + +#if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \ + defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \ + defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \ + defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M) + +# ifdef CONFIG_SCC1_ENET /* use SCC for 10Mbps Ethernet */ + +/* Bits in parallel I/O port registers that have to be set/cleared + * to configure the pins for SCC1 use. + */ +#define PROFF_ENET PROFF_SCC1 +#define CPM_CR_ENET CPM_CR_CH_SCC1 +#define SCC_ENET 0 +#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */ +#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */ +#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */ +#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */ + +#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */ +#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */ +#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */ + +/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to + * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero. + */ +#define SICR_ENET_MASK ((uint)0x000000ff) +#define SICR_ENET_CLKRT ((uint)0x00000026) + +# endif /* CONFIG_SCC1_ENET */ + +# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */ + +#define FEC_ENET + +#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ +#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ +#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ +#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ +#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ +#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ +#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ +#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ +#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ +#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ +#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ +#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ +#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ + +#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ + +# endif /* CONFIG_FEC_ENET */ +#endif /* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */ + +/*** V37 **********************************************************/ + +#ifdef CONFIG_V37 +/* This ENET stuff is for the MPC823 with ethernet on SCC2. Some of + * this may be unique to the Marel V37 configuration. + * Note TENA is on Port B. + */ +#define PROFF_ENET PROFF_SCC2 +#define CPM_CR_ENET CPM_CR_CH_SCC2 +#define SCC_ENET 1 +#define PA_ENET_RXD ((ushort)0x0004) +#define PA_ENET_TXD ((ushort)0x0008) +#define PA_ENET_TCLK ((ushort)0x0400) +#define PA_ENET_RCLK ((ushort)0x0200) +#define PB_ENET_TENA ((uint)0x00002000) +#define PC_ENET_CLSN ((ushort)0x0040) +#define PC_ENET_RENA ((ushort)0x0080) + +#define SICR_ENET_MASK ((uint)0x0000ff00) +#define SICR_ENET_CLKRT ((uint)0x00002e00) +#endif /* CONFIG_V37 */ + + +/*********************************************************************/ + +/* SCC Event register as used by Ethernet. +*/ +#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */ +#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */ +#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */ +#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */ +#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */ +#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */ + +/* SCC Mode Register (PSMR) as used by Ethernet. +*/ +#define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */ +#define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */ +#define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */ +#define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */ +#define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */ +#define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */ +#define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */ +#define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */ +#define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */ +#define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */ +#define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */ +#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */ +#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */ + +/* Buffer descriptor control/status used by Ethernet receive. +*/ +#define BD_ENET_RX_EMPTY ((ushort)0x8000) +#define BD_ENET_RX_WRAP ((ushort)0x2000) +#define BD_ENET_RX_INTR ((ushort)0x1000) +#define BD_ENET_RX_LAST ((ushort)0x0800) +#define BD_ENET_RX_FIRST ((ushort)0x0400) +#define BD_ENET_RX_MISS ((ushort)0x0100) +#define BD_ENET_RX_LG ((ushort)0x0020) +#define BD_ENET_RX_NO ((ushort)0x0010) +#define BD_ENET_RX_SH ((ushort)0x0008) +#define BD_ENET_RX_CR ((ushort)0x0004) +#define BD_ENET_RX_OV ((ushort)0x0002) +#define BD_ENET_RX_CL ((ushort)0x0001) +#define BD_ENET_RX_STATS ((ushort)0x013f) /* All status bits */ + +/* Buffer descriptor control/status used by Ethernet transmit. +*/ +#define BD_ENET_TX_READY ((ushort)0x8000) +#define BD_ENET_TX_PAD ((ushort)0x4000) +#define BD_ENET_TX_WRAP ((ushort)0x2000) +#define BD_ENET_TX_INTR ((ushort)0x1000) +#define BD_ENET_TX_LAST ((ushort)0x0800) +#define BD_ENET_TX_TC ((ushort)0x0400) +#define BD_ENET_TX_DEF ((ushort)0x0200) +#define BD_ENET_TX_HB ((ushort)0x0100) +#define BD_ENET_TX_LC ((ushort)0x0080) +#define BD_ENET_TX_RL ((ushort)0x0040) +#define BD_ENET_TX_RCMASK ((ushort)0x003c) +#define BD_ENET_TX_UN ((ushort)0x0002) +#define BD_ENET_TX_CSL ((ushort)0x0001) +#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */ + +/* SCC as UART +*/ +typedef struct scc_uart { + sccp_t scc_genscc; + uint scc_res1; /* Reserved */ + uint scc_res2; /* Reserved */ + ushort scc_maxidl; /* Maximum idle chars */ + ushort scc_idlc; /* temp idle counter */ + ushort scc_brkcr; /* Break count register */ + ushort scc_parec; /* receive parity error counter */ + ushort scc_frmec; /* receive framing error counter */ + ushort scc_nosec; /* receive noise counter */ + ushort scc_brkec; /* receive break condition counter */ + ushort scc_brkln; /* last received break length */ + ushort scc_uaddr1; /* UART address character 1 */ + ushort scc_uaddr2; /* UART address character 2 */ + ushort scc_rtemp; /* Temp storage */ + ushort scc_toseq; /* Transmit out of sequence char */ + ushort scc_char1; /* control character 1 */ + ushort scc_char2; /* control character 2 */ + ushort scc_char3; /* control character 3 */ + ushort scc_char4; /* control character 4 */ + ushort scc_char5; /* control character 5 */ + ushort scc_char6; /* control character 6 */ + ushort scc_char7; /* control character 7 */ + ushort scc_char8; /* control character 8 */ + ushort scc_rccm; /* receive control character mask */ + ushort scc_rccr; /* receive control character register */ + ushort scc_rlbc; /* receive last break character */ +} scc_uart_t; + +/* SCC Event and Mask registers when it is used as a UART. +*/ +#define UART_SCCM_GLR ((ushort)0x1000) +#define UART_SCCM_GLT ((ushort)0x0800) +#define UART_SCCM_AB ((ushort)0x0200) +#define UART_SCCM_IDL ((ushort)0x0100) +#define UART_SCCM_GRA ((ushort)0x0080) +#define UART_SCCM_BRKE ((ushort)0x0040) +#define UART_SCCM_BRKS ((ushort)0x0020) +#define UART_SCCM_CCR ((ushort)0x0008) +#define UART_SCCM_BSY ((ushort)0x0004) +#define UART_SCCM_TX ((ushort)0x0002) +#define UART_SCCM_RX ((ushort)0x0001) + +/* The SCC PSMR when used as a UART. +*/ +#define SCU_PSMR_FLC ((ushort)0x8000) +#define SCU_PSMR_SL ((ushort)0x4000) +#define SCU_PSMR_CL ((ushort)0x3000) +#define SCU_PSMR_UM ((ushort)0x0c00) +#define SCU_PSMR_FRZ ((ushort)0x0200) +#define SCU_PSMR_RZS ((ushort)0x0100) +#define SCU_PSMR_SYN ((ushort)0x0080) +#define SCU_PSMR_DRT ((ushort)0x0040) +#define SCU_PSMR_PEN ((ushort)0x0010) +#define SCU_PSMR_RPM ((ushort)0x000c) +#define SCU_PSMR_REVP ((ushort)0x0008) +#define SCU_PSMR_TPM ((ushort)0x0003) +#define SCU_PSMR_TEVP ((ushort)0x0003) + +/* CPM Transparent mode SCC. + */ +typedef struct scc_trans { + sccp_t st_genscc; + uint st_cpres; /* Preset CRC */ + uint st_cmask; /* Constant mask for CRC */ +} scc_trans_t; + +#define BD_SCC_TX_LAST ((ushort)0x0800) + +/* IIC parameter RAM. +*/ +typedef struct iic { + ushort iic_rbase; /* Rx Buffer descriptor base address */ + ushort iic_tbase; /* Tx Buffer descriptor base address */ + u_char iic_rfcr; /* Rx function code */ + u_char iic_tfcr; /* Tx function code */ + ushort iic_mrblr; /* Max receive buffer length */ + uint iic_rstate; /* Internal */ + uint iic_rdp; /* Internal */ + ushort iic_rbptr; /* Internal */ + ushort iic_rbc; /* Internal */ + uint iic_rxtmp; /* Internal */ + uint iic_tstate; /* Internal */ + uint iic_tdp; /* Internal */ + ushort iic_tbptr; /* Internal */ + ushort iic_tbc; /* Internal */ + uint iic_txtmp; /* Internal */ + uint iic_res; /* reserved */ + ushort iic_rpbase; /* Relocation pointer */ + ushort iic_res2; /* reserved */ +} iic_t; + +/* SPI parameter RAM. +*/ +typedef struct spi { + ushort spi_rbase; /* Rx Buffer descriptor base address */ + ushort spi_tbase; /* Tx Buffer descriptor base address */ + u_char spi_rfcr; /* Rx function code */ + u_char spi_tfcr; /* Tx function code */ + ushort spi_mrblr; /* Max receive buffer length */ + uint spi_rstate; /* Internal */ + uint spi_rdp; /* Internal */ + ushort spi_rbptr; /* Internal */ + ushort spi_rbc; /* Internal */ + uint spi_rxtmp; /* Internal */ + uint spi_tstate; /* Internal */ + uint spi_tdp; /* Internal */ + ushort spi_tbptr; /* Internal */ + ushort spi_tbc; /* Internal */ + uint spi_txtmp; /* Internal */ + uint spi_res; + ushort spi_rpbase; /* Relocation pointer */ + ushort spi_res2; +} spi_t; + +/* SPI Mode register. +*/ +#define SPMODE_LOOP ((ushort)0x4000) /* Loopback */ +#define SPMODE_CI ((ushort)0x2000) /* Clock Invert */ +#define SPMODE_CP ((ushort)0x1000) /* Clock Phase */ +#define SPMODE_DIV16 ((ushort)0x0800) /* BRG/16 mode */ +#define SPMODE_REV ((ushort)0x0400) /* Reversed Data */ +#define SPMODE_MSTR ((ushort)0x0200) /* SPI Master */ +#define SPMODE_EN ((ushort)0x0100) /* Enable */ +#define SPMODE_LENMSK ((ushort)0x00f0) /* character length */ +#define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */ + +#define SPMODE_LEN(x) ((((x)-1)&0xF)<<4) +#define SPMODE_PM(x) ((x) &0xF) + +/* HDLC parameter RAM. +*/ + +typedef struct hdlc_pram_s { + /* + * SCC parameter RAM + */ + ushort rbase; /* Rx Buffer descriptor base address */ + ushort tbase; /* Tx Buffer descriptor base address */ + uchar rfcr; /* Rx function code */ + uchar tfcr; /* Tx function code */ + ushort mrblr; /* Rx buffer length */ + ulong rstate; /* Rx internal state */ + ulong rptr; /* Rx internal data pointer */ + ushort rbptr; /* rb BD Pointer */ + ushort rcount; /* Rx internal byte count */ + ulong rtemp; /* Rx temp */ + ulong tstate; /* Tx internal state */ + ulong tptr; /* Tx internal data pointer */ + ushort tbptr; /* Tx BD pointer */ + ushort tcount; /* Tx byte count */ + ulong ttemp; /* Tx temp */ + ulong rcrc; /* temp receive CRC */ + ulong tcrc; /* temp transmit CRC */ + /* + * HDLC specific parameter RAM + */ + uchar res[4]; /* reserved */ + ulong c_mask; /* CRC constant */ + ulong c_pres; /* CRC preset */ + ushort disfc; /* discarded frame counter */ + ushort crcec; /* CRC error counter */ + ushort abtsc; /* abort sequence counter */ + ushort nmarc; /* nonmatching address rx cnt */ + ushort retrc; /* frame retransmission cnt */ + ushort mflr; /* maximum frame length reg */ + ushort max_cnt; /* maximum length counter */ + ushort rfthr; /* received frames threshold */ + ushort rfcnt; /* received frames count */ + ushort hmask; /* user defined frm addr mask */ + ushort haddr1; /* user defined frm address 1 */ + ushort haddr2; /* user defined frm address 2 */ + ushort haddr3; /* user defined frm address 3 */ + ushort haddr4; /* user defined frm address 4 */ + ushort tmp; /* temp */ + ushort tmp_mb; /* temp */ +} hdlc_pram_t; + +/* CPM interrupts. There are nearly 32 interrupts generated by CPM + * channels or devices. All of these are presented to the PPC core + * as a single interrupt. The CPM interrupt handler dispatches its + * own handlers, in a similar fashion to the PPC core handler. We + * use the table as defined in the manuals (i.e. no special high + * priority and SCC1 == SCCa, etc...). + */ +#define CPMVEC_NR 32 +#define CPMVEC_OFFSET 0x00010000 +#define CPMVEC_PIO_PC15 ((ushort)0x1f | CPMVEC_OFFSET) +#define CPMVEC_SCC1 ((ushort)0x1e | CPMVEC_OFFSET) +#define CPMVEC_SCC2 ((ushort)0x1d | CPMVEC_OFFSET) +#define CPMVEC_SCC3 ((ushort)0x1c | CPMVEC_OFFSET) +#define CPMVEC_SCC4 ((ushort)0x1b | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC14 ((ushort)0x1a | CPMVEC_OFFSET) +#define CPMVEC_TIMER1 ((ushort)0x19 | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC13 ((ushort)0x18 | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC12 ((ushort)0x17 | CPMVEC_OFFSET) +#define CPMVEC_SDMA_CB_ERR ((ushort)0x16 | CPMVEC_OFFSET) +#define CPMVEC_IDMA1 ((ushort)0x15 | CPMVEC_OFFSET) +#define CPMVEC_IDMA2 ((ushort)0x14 | CPMVEC_OFFSET) +#define CPMVEC_TIMER2 ((ushort)0x12 | CPMVEC_OFFSET) +#define CPMVEC_RISCTIMER ((ushort)0x11 | CPMVEC_OFFSET) +#define CPMVEC_I2C ((ushort)0x10 | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC11 ((ushort)0x0f | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC10 ((ushort)0x0e | CPMVEC_OFFSET) +#define CPMVEC_TIMER3 ((ushort)0x0c | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC9 ((ushort)0x0b | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC8 ((ushort)0x0a | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC7 ((ushort)0x09 | CPMVEC_OFFSET) +#define CPMVEC_TIMER4 ((ushort)0x07 | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC6 ((ushort)0x06 | CPMVEC_OFFSET) +#define CPMVEC_SPI ((ushort)0x05 | CPMVEC_OFFSET) +#define CPMVEC_SMC1 ((ushort)0x04 | CPMVEC_OFFSET) +#define CPMVEC_SMC2 ((ushort)0x03 | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC5 ((ushort)0x02 | CPMVEC_OFFSET) +#define CPMVEC_PIO_PC4 ((ushort)0x01 | CPMVEC_OFFSET) +#define CPMVEC_ERROR ((ushort)0x00 | CPMVEC_OFFSET) + +extern void irq_install_handler(int vec, void (*handler)(void *), void *dev_id); + +/* CPM interrupt configuration vector. +*/ +#define CICR_SCD_SCC4 ((uint)0x00c00000) /* SCC4 @ SCCd */ +#define CICR_SCC_SCC3 ((uint)0x00200000) /* SCC3 @ SCCc */ +#define CICR_SCB_SCC2 ((uint)0x00040000) /* SCC2 @ SCCb */ +#define CICR_SCA_SCC1 ((uint)0x00000000) /* SCC1 @ SCCa */ +#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrrupt */ +#define CICR_HP_MASK ((uint)0x00001f00) /* Hi-pri int. */ +#define CICR_IEN ((uint)0x00000080) /* Int. enable */ +#define CICR_SPS ((uint)0x00000001) /* SCC Spread */ +#endif /* __CPM_8XX__ */ |