diff options
Diffstat (limited to 'qemu/roms/u-boot/doc/README.nokia_rx51')
| -rw-r--r-- | qemu/roms/u-boot/doc/README.nokia_rx51 | 104 |
1 files changed, 0 insertions, 104 deletions
diff --git a/qemu/roms/u-boot/doc/README.nokia_rx51 b/qemu/roms/u-boot/doc/README.nokia_rx51 deleted file mode 100644 index 586ed7c1c..000000000 --- a/qemu/roms/u-boot/doc/README.nokia_rx51 +++ /dev/null @@ -1,104 +0,0 @@ -Board: Nokia RX-51 aka N900 - -This board definition results in a u-boot.bin which can be chainloaded -from NOLO in qemu or on a real N900. It does very little hardware config -because NOLO has already configured the board. Only needed is enabling -internal eMMC memory via twl4030 regulator which is not enabled by NOLO. - -NOLO is expecting a kernel image and will treat any image it finds in -onenand as such. This u-boot is intended to be flashed to the N900 like -a kernel. In order to transparently boot the original kernel, it will be -appended to u-boot.bin at 0x40000. NOLO will load the entire image into -(random) memory and execute u-boot, which saves hw revision, boot reason -and boot mode ATAGs set by NOLO. Then the bootscripts will attempt to load -uImage or boot.scr from a fat, ext2/ext3 or ext4 filesystem in external -SD card or internal eMMC memory. If this fails or keyboard is closed then -the appended kernel image will be booted using some generated and some -stored ATAGs (see boot order). - -There is support for hardware watchdog. Hardware watchdog is started by -NOLO so u-boot must kick watchdog to prevent reboot device (but not very -often, max every 2 seconds). There is also support for framebuffer display -output with ANSI espace codes and the N900 HW keyboard input. USB tty works -but is disabled because it prevents the current Maemo kernel from booting. - -When U-Boot is starting it enable IBE bit in Auxiliary Control Register, -which is needed for Thumb-2 ISA support. It is workaround for errata 430973. - -Default boot order: - - * 0. if keyboard is closed boot automatically attached kernel image - * 1. try boot from external SD card - * 2. try boot from internal eMMC memory - * 3. try boot from attached kernel image - -Boot from SD or eMMC in this order: - - * 1. - * 1.1 find boot.scr on first fat partition - * 1.2 find uImage on first fat parition - * 1.3 same order for 2. - 4. fat partition - * 2. same as 1. but for ext2/3 partition - * 3. same as 1. but for ext4 partition - - -Available additional commands/variables: - - * run sercon - Use serial port for control - * run usbcon - Use usbtty for control - * run vgacon - Use framebuffer and HW keyboard for control (default) - - * run sdboot - Boot from external SD card (see boot order) - * run emmcboot - Boot from internal eMMC memory (see boot order) - * run attachboot - Boot attached kernel image (attached to U-Boot binary) - - * run scriptload - Load boot script ${mmcscriptfile} - * run scriptboot - Run loaded boot script - * run kernload - Load kernel image ${mmckernfile} - * run initrdload - Load initrd image ${mmcinitrdfile} - * run kernboot - Boot loaded kernel image - * run kerninitrdboot - Boot loaded kernel image with loaded initrd image - - * run trymmcscriptboot - Try to load and boot script ${mmcscriptfile} - * run trymmckernboot - Try to load and boot kernel image ${mmckernfile} - * run trymmckerninitrdboot - Try to load and boot kernel image ${mmckernfile} - with initrd image ${mmcinitrdfile} - -Additional variables for loading files from mmc: - - * mmc ${mmcnum} (0 - external, 1 - internal) - * partition number ${mmcpart} (1 - 4) - * parition type ${mmctype} (fat, ext2) - -Additional varuables for booting kernel: - - * setup_omap_atag - Add OMAP table into atags structure (needs maemo kernel) - * setup_console_atag - Enable serial console in OMAP table - * setup_boot_reason_atag - Change boot reason in OMAP table - * setup_boot_mode_atag - Change boot mode in OMAP table - -USB TTY: - - Maemo kernel 2.6.28 will crash if u-boot enable usb tty. So USB TTY is disabled. - For enabling USB TTY just add this line to file include/configs/nokia_rx51.h - - #define CONFIG_USB_TTY - - -ONENAND support: - - ONENAND support is disabled because not working yet and cause linux kernel to - crash or no access to mtd. For enabling ONENAND support add this line at begin - of file include/configs/nokia_rx51.h - - #define ONENAND_SUPPORT - - -UBIFS support: - - UBIFS support is disabled, because U-Boot image is too big and cannot be - flashed with attached zImage to RX-51 kernel nand area. For enabling UBIFS - support first enable ONENAND support and then add this line at begin of file - include/configs/nokia_rx51.h - - #define UBIFS_SUPPORT |