diff options
Diffstat (limited to 'qemu/roms/u-boot/doc/README.arm-relocation')
| -rw-r--r-- | qemu/roms/u-boot/doc/README.arm-relocation | 193 |
1 files changed, 193 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/doc/README.arm-relocation b/qemu/roms/u-boot/doc/README.arm-relocation new file mode 100644 index 000000000..645b3746c --- /dev/null +++ b/qemu/roms/u-boot/doc/README.arm-relocation @@ -0,0 +1,193 @@ +To make relocation on arm working, the following changes are done: + +At arch level: add linker flag -pie + + This causes the linker to generate fixup tables .rel.dyn and .dynsym, + which must be applied to the relocated image before transferring + control to it. + + These fixups are described in the ARM ELF documentation as type 23 + (program-base-relative) and 2 (symbol-relative) + +At cpu level: modify linker file and add a relocation and fixup loop + + the linker file must be modified to include the .rel.dyn and .dynsym + tables in the binary image, and to provide symbols for the relocation + code to access these tables + + The relocation and fixup loop must be executed after executing + board_init_f at initial location and before executing board_init_r + at final location. + +At board level: + + dram_init(): bd pointer is now at this point not accessible, so only + detect the real dramsize, and store it in gd->ram_size. Bst detected + with get_ram_size(). + +TODO: move also dram initialization there on boards where it is possible. + + Setup of the the bd_t dram bank info is done in the new function + dram_init_banksize() called after bd is accessible. + +At lib level: + + Board.c code is adapted from ppc code + +* WARNING ** WARNING ** WARNING ** WARNING ** WARNING ** WARNING ** WARNING * + +Boards which are not fixed to support relocation will be REMOVED! + +----------------------------------------------------------------------------- + +For boards which boot from spl, it is possible to save one copy +if CONFIG_SYS_TEXT_BASE == relocation address! This prevents that uboot code +is copied again in relocate_code(). + +example for the tx25 board booting from NAND Flash: + +a) cpu starts +b) it copies the first page in nand to internal ram + (spl code) +c) end executes this code +d) this initialize CPU, RAM, ... and copy itself to RAM + (this bin must fit in one page, so board_init_f() + don;t fit in it ... ) +e) there it copy u-boot to CONFIG_SYS_NAND_U_BOOT_DST and + starts this image @ CONFIG_SYS_NAND_U_BOOT_START +f) u-boot code steps through board_init_f() and calculates + the relocation address and copy itself to it + +If CONFIG_SYS_TEXT_BASE == relocation address, the copying of u-boot +in f) could be saved. + +----------------------------------------------------------------------------- + +TODO + +- fill in bd_t infos (check) +- adapt all boards + +- maybe adapt CONFIG_SYS_TEXT_BASE (this must be checked from board maintainers) + This *must* be done for boards, which boot from NOR flash + + on other boards if CONFIG_SYS_TEXT_BASE = relocation baseaddr, this saves + one copying from u-boot code. + +- new function dram_init_banksize() is actual board specific. Maybe + we make a weak default function in arch/arm/lib/board.c ? + +----------------------------------------------------------------------------- + +Relocation with SPL (example for the tx25 booting from NAND Flash): + +- cpu copies the first page from NAND to 0xbb000000 (IMX_NFC_BASE) + and start with code execution on this address. + +- The First page contains u-boot code from drivers/mtd/nand/mxc_nand_spl.c + which inits the dram, cpu registers, reloacte itself to CONFIG_SPL_TEXT_BASE and loads + the "real" u-boot to CONFIG_SYS_NAND_U_BOOT_DST and starts execution + @CONFIG_SYS_NAND_U_BOOT_START + +- This u-boot does no RAM init, nor CPU register setup. Just look + where it has to copy and relocate itself to this address. If + relocate address = CONFIG_SYS_TEXT_BASE (not the same, as the + CONFIG_SPL_TEXT_BASE from the spl code), then there is no need + to copy, just go on with bss clear and jump to board_init_r. + +----------------------------------------------------------------------------- + +How ELF relocations 23 and 2 work. + +TBC + +------------------------------------------------------------------------------------- + +Debugging u-boot in RAM: +(example on the qong board) + +----------------- + +a) start debugger + +arm-linux-gdb u-boot + +[hs@pollux u-boot]$ arm-linux-gdb u-boot +GNU gdb Red Hat Linux (6.7-2rh) +Copyright (C) 2007 Free Software Foundation, Inc. +License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html> +This is free software: you are free to change and redistribute it. +There is NO WARRANTY, to the extent permitted by law. Type "show copying" +and "show warranty" for details. +This GDB was configured as "--host=i686-pc-linux-gnu --target=arm-linux". +The target architecture is set automatically (currently arm) +.. +(gdb) + +----------------- + +b) connect to target + +target remote bdi10:2001 + +(gdb) target remote bdi10:2001 +Remote debugging using bdi10:2001 +0x8ff17f10 in ?? () +(gdb) + +----------------- + +c) discard symbol-file + +(gdb) symbol-file +Discard symbol table from `/home/hs/celf/u-boot/u-boot'? (y or n) y +No symbol file now. +(gdb) + +----------------- + +d) load new symbol table: + +(gdb) add-symbol-file u-boot 0x8ff08000 +add symbol table from file "u-boot" at + .text_addr = 0x8ff08000 +(y or n) y +Reading symbols from /home/hs/celf/u-boot/u-boot...done. +(gdb) c +Continuing. +^C +Program received signal SIGSTOP, Stopped (signal). +0x8ff17f18 in serial_getc () at serial_mxc.c:192 +192 while (__REG(UART_PHYS + UTS) & UTS_RXEMPTY); +(gdb) + +add-symbol-file u-boot 0x8ff08000 + ^^^^^^^^^^ + get this address from u-boot bdinfo command + or get it from gd->relocaddr in gdb + + => bdinfo +rch_number = XXXXXXXXXX +boot_params = XXXXXXXXXX +DRAM bank = XXXXXXXXXX +-> start = XXXXXXXXXX +-> size = XXXXXXXXXX +ethaddr = XXXXXXXXXX +ip_addr = XXXXXXXXXX +baudrate = XXXXXXXXXX +TLB addr = XXXXXXXXXX +relocaddr = 0x8ff08000 + ^^^^^^^^^^ +reloc off = XXXXXXXXXX +irq_sp = XXXXXXXXXX +sp start = XXXXXXXXXX +FB base = XXXXXXXXXX + +or interrupt execution by any means and re-load the symbols at the location +specified by gd->relocaddr -- this is only valid after board_init_f. + +(gdb) set $s = gd->relocaddr +(gdb) symbol-file +(gdb) add-symbol-file u-boot $s + +Now you can use gdb as usual :-) |