diff options
Diffstat (limited to 'qemu/roms/u-boot/board/xes/xpedite537x')
| -rw-r--r-- | qemu/roms/u-boot/board/xes/xpedite537x/Makefile | 13 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/xes/xpedite537x/ddr.c | 234 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/xes/xpedite537x/law.c | 26 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/xes/xpedite537x/tlb.c | 83 | ||||
| -rw-r--r-- | qemu/roms/u-boot/board/xes/xpedite537x/xpedite537x.c | 82 |
5 files changed, 438 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/board/xes/xpedite537x/Makefile b/qemu/roms/u-boot/board/xes/xpedite537x/Makefile new file mode 100644 index 000000000..2dca0d751 --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite537x/Makefile @@ -0,0 +1,13 @@ +# +# Copyright 2008 Extreme Engineering Solutions, Inc. +# Copyright 2007 Freescale Semiconductor, Inc. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += xpedite537x.o +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o diff --git a/qemu/roms/u-boot/board/xes/xpedite537x/ddr.c b/qemu/roms/u-boot/board/xes/xpedite537x/ddr.c new file mode 100644 index 000000000..56b5a187d --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite537x/ddr.c @@ -0,0 +1,234 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> + +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> + +void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address) +{ + i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, + sizeof(ddr2_spd_eeprom_t)); +} + +/* + * There are four board-specific SDRAM timing parameters which must be + * calculated based on the particular PCB artwork. These are: + * 1.) CPO (Read Capture Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths and + * chip-specific internal delays. + * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths. + * Unless clock and DQ lanes are very different + * lengths (>2"), this should be set to the nominal value + * of 1/2 clock delay. + * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control) + * - DDR_SDRAM_CLK_CNTL register + * Source: Signal Integrity Simulations + * 4.) 2T Timing on Addr/Ctl + * - TIMING_CFG_2 register + * Source: Signal Integrity Simulations + * Usually only needed with heavy load/very high speed (>DDR2-800) + * + * ====== XPedite5370 DDR2-600 read delay calculations ====== + * + * See Freescale's App Note AN2583 as refrence. This document also + * contains the chip-specific delays for 8548E, 8572, etc. + * + * For MPC8572E + * Minimum chip delay (Ch 0): 1.372ns + * Maximum chip delay (Ch 0): 2.914ns + * Minimum chip delay (Ch 1): 1.220ns + * Maximum chip delay (Ch 1): 2.595ns + * + * CLK adjust = 5 (from simulations) = 5/8* 3.33ns = 2080ps + * + * Minimum delay calc (Ch 0): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 2.3" * 180 - 400ps + 1.9" * 180 + 2080ps + 1372ps + * = 3808ps + * = 3.808ns + * + * Maximum delay calc (Ch 0): + * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly + * 2.3" * 180 + 400ps + 2.4" * 180 + 2080ps + 2914ps + * = 6240ps + * = 6.240ns + * + * Minimum delay calc (Ch 1): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180- 400ps + 0.7" * 180 + 2080ps + 1220ps + * = 3288ps + * = 3.288ns + * + * Maximum delay calc (Ch 1): + * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180+ 400ps + 1.1" * 180 + 2080ps + 2595ps + * = 5536ps + * = 5.536ns + * + * Ch.0: 3.808ns to 6.240ns additional delay needed (pick 5ns as target) + * This is 1.5 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) + * Ch.1: 3.288ns to 5.536ns additional delay needed (pick 4.4ns as target) + * This is 1.32 clock cycles, pick CPO = READ_LAT + 5/4 (0x7) + * + * + * ====== XPedite5370 DDR2-800 read delay calculations ====== + * + * See Freescale's App Note AN2583 as refrence. This document also + * contains the chip-specific delays for 8548E, 8572, etc. + * + * For MPC8572E + * Minimum chip delay (Ch 0): 1.372ns + * Maximum chip delay (Ch 0): 2.914ns + * Minimum chip delay (Ch 1): 1.220ns + * Maximum chip delay (Ch 1): 2.595ns + * + * CLK adjust = 5 (from simulations) = 5/8* 2.5ns = 1563ps + * + * Minimum delay calc (Ch 0): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 2.3" * 180 - 350ps + 1.9" * 180 + 1563ps + 1372ps + * = 3341ps + * = 3.341ns + * + * Maximum delay calc (Ch 0): + * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly + * 2.3" * 180 + 350ps + 2.4" * 180 + 1563ps + 2914ps + * = 5673ps + * = 5.673ns + * + * Minimum delay calc (Ch 1): + * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180- 350ps + 0.7" * 180 + 1563ps + 1220ps + * = 2822ps + * = 2.822ns + * + * Maximum delay calc (Ch 1): + * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly + * 1.46" * 180+ 350ps + 1.1" * 180 + 1563ps + 2595ps + * = 4968ps + * = 4.968ns + * + * Ch.0: 3.341ns to 5.673ns additional delay needed (pick 4.5ns as target) + * This is 1.8 clock cycles, pick CPO = READ_LAT + 7/4 (0x9) + * Ch.1: 2.822ns to 4.968ns additional delay needed (pick 3.9ns as target) + * This is 1.56 clock cycles, pick CPO = READ_LAT + 3/2 (0x8) + * + * Write latency (WR_DATA_DELAY) is calculated by doing the following: + * + * The DDR SDRAM specification requires DQS be received no sooner than + * 75% of an SDRAM clock period—and no later than 125% of a clock + * period—from the capturing clock edge of the command/address at the + * SDRAM. + * + * Based on the above tracelengths, the following are calculated: + * Ch. 0 8572 to DRAM propagation (DQ lanes) : 1.9" * 180 = 0.342ns + * Ch. 0 8572 to DRAM propagation (CLKs) : 2.3" * 180 = 0.414ns + * Ch. 1 8572 to DRAM propagation (DQ lanes) : 0.7" * 180 = 0.126ns + * Ch. 1 8572 to DRAM propagation (CLKs ) : 1.47" * 180 = 0.264ns + * + * Difference in arrival time CLK vs. DQS: + * Ch. 0 0.072ns + * Ch. 1 0.138ns + * + * Both of these values are much less than 25% of the clock + * period at DDR2-600 or DDR2-800, so no additional delay is needed over + * the 1/2 cycle which normally aligns the first DQS transition + * exactly WL (CAS latency minus one cycle) after the CAS strobe. + * See Figure 9-53 in MPC8572E manual: "1/2 delay" in Freescale's + * terminology corresponds to exactly one clock period delay after + * the CAS strobe. (due to the fact that the "delay" is referenced + * from the *falling* edge of the CLK, just after the rising edge + * which the CAS strobe is latched on. + */ + +typedef struct board_memctl_options { + uint16_t datarate_mhz_low; + uint16_t datarate_mhz_high; + uint8_t clk_adjust; + uint8_t cpo_override; + uint8_t write_data_delay; +} board_memctl_options_t; + +static struct board_memctl_options bopts_ctrl[][2] = { + { + /* Controller 0 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 9, + .write_data_delay = 2, + }, + }, + { + /* Controller 1 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 7, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + }, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + struct board_memctl_options *bopts = bopts_ctrl[ctrl_num]; + sys_info_t sysinfo; + int i; + unsigned int datarate; + + get_sys_info(&sysinfo); + datarate = sysinfo.freq_ddrbus / 1000 / 1000; + + for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) { + if ((bopts[i].datarate_mhz_low <= datarate) && + (bopts[i].datarate_mhz_high >= datarate)) { + debug("controller %d:\n", ctrl_num); + debug(" clk_adjust = %d\n", bopts[i].clk_adjust); + debug(" cpo = %d\n", bopts[i].cpo_override); + debug(" write_data_delay = %d\n", + bopts[i].write_data_delay); + popts->clk_adjust = bopts[i].clk_adjust; + popts->cpo_override = bopts[i].cpo_override; + popts->write_data_delay = bopts[i].write_data_delay; + } + } + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; +} diff --git a/qemu/roms/u-boot/board/xes/xpedite537x/law.c b/qemu/roms/u-boot/board/xes/xpedite537x/law.c new file mode 100644 index 000000000..092c9ac1e --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite537x/law.c @@ -0,0 +1,26 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> + +/* + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/qemu/roms/u-boot/board/xes/xpedite537x/tlb.c b/qemu/roms/u-boot/board/xes/xpedite537x/tlb.c new file mode 100644 index 000000000..6d83f859e --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite537x/tlb.c @@ -0,0 +1,83 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * Copyright 2008 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* W**G* - NOR flashes */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - NAND flash */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + + /* **M** - Boot page for secondary processors */ + SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, CONFIG_BPTR_VIRT_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, + 0, 3, BOOKE_PAGESZ_4K, 1), + +#ifdef CONFIG_PCIE1 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_1G, 1), +#endif + +#ifdef CONFIG_PCIE2 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), +#endif + +#ifdef CONFIG_PCIE3 + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256M, 1), +#endif + +#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3) + /* *I*G* - PCIe */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_64M, 1), +#endif + +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/qemu/roms/u-boot/board/xes/xpedite537x/xpedite537x.c b/qemu/roms/u-boot/board/xes/xpedite537x/xpedite537x.c new file mode 100644 index 000000000..efd563b26 --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite537x/xpedite537x.c @@ -0,0 +1,82 @@ +/* + * Copyright 2008 Extreme Engineering Solutions, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <command.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/io.h> +#include <asm/cache.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <pca953x.h> + +DECLARE_GLOBAL_DATA_PTR; + +extern void ft_board_pci_setup(void *blob, bd_t *bd); + +static void flash_cs_fixup(void) +{ + int flash_sel; + + /* + * Print boot dev and swap flash flash chip selects if booted from 2nd + * flash. Swapping chip selects presents user with a common memory + * map regardless of which flash was booted from. + */ + flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) & + CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS)); + printf("Flash: Executed from flash%d\n", flash_sel ? 2 : 1); + + if (flash_sel) { + set_lbc_br(0, CONFIG_SYS_BR1_PRELIM); + set_lbc_or(0, CONFIG_SYS_OR1_PRELIM); + + set_lbc_br(1, CONFIG_SYS_BR0_PRELIM); + set_lbc_or(1, CONFIG_SYS_OR0_PRELIM); + } +} + +int board_early_init_r(void) +{ + /* Initialize PCA9557 devices */ + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR2, 0xff, 0); + pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR3, 0xff, 0); + + /* + * Remap NOR flash region to caching-inhibited + * so that flash can be erased/programmed properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* Invalidate existing TLB entry for NOR flash */ + disable_tlb(0); + set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + (CONFIG_SYS_FLASH_BASE2 & 0xf0000000), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_256M, 1); + + flash_cs_fixup(); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#ifdef CONFIG_PCI + ft_board_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); +} +#endif |