diff options
Diffstat (limited to 'qemu/roms/u-boot/board/xes/xpedite517x/ddr.c')
| -rw-r--r-- | qemu/roms/u-boot/board/xes/xpedite517x/ddr.c | 124 |
1 files changed, 124 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/board/xes/xpedite517x/ddr.c b/qemu/roms/u-boot/board/xes/xpedite517x/ddr.c new file mode 100644 index 000000000..fd602ea7e --- /dev/null +++ b/qemu/roms/u-boot/board/xes/xpedite517x/ddr.c @@ -0,0 +1,124 @@ +/* + * Copyright 2009 Extreme Engineering Solutions, Inc. + * Copyright 2007-2008 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <fsl_ddr_sdram.h> +#include <fsl_ddr_dimm_params.h> + +void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address) +{ + i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd, + sizeof(ddr2_spd_eeprom_t)); +} + +/* + * There are four board-specific SDRAM timing parameters which must be + * calculated based on the particular PCB artwork. These are: + * 1.) CPO (Read Capture Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths and + * chip-specific internal delays. + * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay) + * - TIMING_CFG_2 register + * Source: Calculation based on board trace lengths. + * Unless clock and DQ lanes are very different + * lengths (>2"), this should be set to the nominal value + * of 1/2 clock delay. + * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control) + * - DDR_SDRAM_CLK_CNTL register + * Source: Signal Integrity Simulations + * 4.) 2T Timing on Addr/Ctl + * - TIMING_CFG_2 register + * Source: Signal Integrity Simulations + * Usually only needed with heavy load/very high speed (>DDR2-800) + * + * PCB routing on the XPedite5170 is nearly identical to the XPedite5370 + * so we use the XPedite5370 settings as a basis for the XPedite5170. + */ + +typedef struct board_memctl_options { + uint16_t datarate_mhz_low; + uint16_t datarate_mhz_high; + uint8_t clk_adjust; + uint8_t cpo_override; + uint8_t write_data_delay; +} board_memctl_options_t; + +static struct board_memctl_options bopts_ctrl[][2] = { + { + /* Controller 0 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 9, + .write_data_delay = 2, + }, + }, + { + /* Controller 1 */ + { + /* DDR2 600/667 */ + .datarate_mhz_low = 500, + .datarate_mhz_high = 750, + .clk_adjust = 5, + .cpo_override = 7, + .write_data_delay = 2, + }, + { + /* DDR2 800 */ + .datarate_mhz_low = 750, + .datarate_mhz_high = 850, + .clk_adjust = 5, + .cpo_override = 8, + .write_data_delay = 2, + }, + }, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + struct board_memctl_options *bopts = bopts_ctrl[ctrl_num]; + sys_info_t sysinfo; + int i; + unsigned int datarate; + + get_sys_info(&sysinfo); + datarate = get_ddr_freq(0) / 1000000; + + for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) { + if ((bopts[i].datarate_mhz_low <= datarate) && + (bopts[i].datarate_mhz_high >= datarate)) { + debug("controller %d:\n", ctrl_num); + debug(" clk_adjust = %d\n", bopts[i].clk_adjust); + debug(" cpo = %d\n", bopts[i].cpo_override); + debug(" write_data_delay = %d\n", + bopts[i].write_data_delay); + popts->clk_adjust = bopts[i].clk_adjust; + popts->cpo_override = bopts[i].cpo_override; + popts->write_data_delay = bopts[i].write_data_delay; + } + } + + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; +} |