4 files changed, 415 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/board/sheldon/simpc8313/Makefile b/qemu/roms/u-boot/board/sheldon/simpc8313/Makefile
new file mode 100644
index 000000000..a824c41d9
--- /dev/null
+++ b/qemu/roms/u-boot/board/sheldon/simpc8313/Makefile
@@ -0,0 +1,8 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= simpc8313.o sdram.o
diff --git a/qemu/roms/u-boot/board/sheldon/simpc8313/README.simpc8313 b/qemu/roms/u-boot/board/sheldon/simpc8313/README.simpc8313
new file mode 100644
index 000000000..b362c6aee
--- /dev/null
+++ b/qemu/roms/u-boot/board/sheldon/simpc8313/README.simpc8313
@@ -0,0 +1,80 @@
+Sheldon Instruments SIMPC8313 Board
+-----------------------------------------
+
+1.	Board Switches and Jumpers
+
+	S2 is used to set CFG_RESET_SOURCE.
+
+	To boot the image in Large page NAND flash, use these DIP
+	switch settings for S2:
+
+	+----------+ ON
+	| * * **** |
+	|  * *     |
+	+----------+
+	  12345678
+
+	To boot the image in Small page NAND flash, use these DIP
+	switch settings for S2:
+
+	+----------+ ON
+	| *** **** |
+	|    *     |
+	+----------+
+	  12345678
+	(where the '*' indicates the position of the tab of the switch.)
+
+2.	Memory Map
+	The memory map looks like this:
+
+	0x0000_0000	0x1fff_ffff	DDR			512M
+	0x8000_0000	0x8fff_ffff	PCI MEM			256M
+	0x9000_0000	0x9fff_ffff	PCI_MMIO		256M
+	0xe000_0000	0xe00f_ffff	IMMR			1M
+	0xe200_0000	0xe20f_ffff	PCI IO			16M
+	0xe280_0000	0xe280_7fff	NAND FLASH (CS0)	32K
+	or
+	0xe280_0000	0xe281_ffff	NAND FLASH (CS0)	128K
+	0xff00_0000	0xff00_7fff	FPGA (CS1)		1M
+
+3.	Compilation
+
+	Assuming you're using BASH (or similar) as your shell:
+
+	export CROSS_COMPILE=your-cross-compiler-prefix-
+	make distclean
+	make SIMPC8313_LP_config
+	(or make SIMPC8313_SP_config, depending on the page size
+	of your NAND flash)
+	make
+
+4.	Downloading and Flashing Images
+
+4.1	Reflash U-boot Image using U-boot
+
+	=>run update_uboot
+
+	You may want to try
+	=>tftp $loadaddr $uboot
+	first, to make sure that the TFTP load will succeed before it
+	goes ahead and wipes out your current firmware.  And of course,
+	if the new u-boot doesn't boot, you can plug the board into
+	your PCI slot and with the supplied driver and sample app
+	you can reburn a working u-boot.
+
+4.2	Downloading and Booting Linux Kernel
+
+	Ensure that all networking-related environment variables are set
+	properly (including ipaddr, serverip, gatewayip (if needed),
+	netmask, ethaddr, eth1addr, fdtfile, and bootfile).
+
+	=>tftp $loadaddr uImage
+	=>nand write $loadaddr kernel $filesize
+	=>tftp $loadaddr $fdtfile
+	=>nand write $loadaddr 7e0000 1800
+
+	=>boot
+
+5	Notes
+
+	The console baudrate for SIMPC8313 is 115200bps.
diff --git a/qemu/roms/u-boot/board/sheldon/simpc8313/sdram.c b/qemu/roms/u-boot/board/sheldon/simpc8313/sdram.c
new file mode 100644
index 000000000..7c12fe851
--- /dev/null
+++ b/qemu/roms/u-boot/board/sheldon/simpc8313/sdram.c
@@ -0,0 +1,177 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ * Copyright (C) Sheldon Instruments, Inc. 2008
+ *
+ * Author: Ron Madrid <info@sheldoninst.com>
+ *
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc83xx.h>
+#include <spd_sdram.h>
+#include <asm/bitops.h>
+#include <asm/io.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static long fixed_sdram(void);
+
+#if defined(CONFIG_NAND_SPL)
+void si_wait_i2c(void)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+
+	while (!(__raw_readb(&im->i2c[0].sr) & 0x02))
+		;
+
+	__raw_writeb(0x00, &im->i2c[0].sr);
+
+	sync();
+
+	return;
+}
+
+void si_read_i2c(u32 lbyte, int count, u8 *buffer)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+	u32 i;
+	u8 chip = 0x50 << 1; /* boot sequencer I2C */
+	u32 ubyte = (lbyte & 0xff00) >> 8;
+
+	lbyte &= 0xff;
+
+	/*
+	 * Set up controller
+	 */
+	__raw_writeb(0x3f, &im->i2c[0].fdr);
+	__raw_writeb(0x00, &im->i2c[0].adr);
+	__raw_writeb(0x00, &im->i2c[0].sr);
+	__raw_writeb(0x00, &im->i2c[0].dr);
+
+	while (__raw_readb(&im->i2c[0].sr) & 0x20)
+		;
+
+	/*
+	 * Writing address to device
+	 */
+	__raw_writeb(0xb0, &im->i2c[0].cr);
+	sync();
+	__raw_writeb(chip, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(0xb0, &im->i2c[0].cr);
+	sync();
+	__raw_writeb(ubyte, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(lbyte, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(0xb4, &im->i2c[0].cr);
+	sync();
+	__raw_writeb(chip + 1, &im->i2c[0].dr);
+	si_wait_i2c();
+
+	__raw_writeb(0xa0, &im->i2c[0].cr);
+	sync();
+
+	/*
+	 * Dummy read
+	 */
+	__raw_readb(&im->i2c[0].dr);
+
+	si_wait_i2c();
+
+	/*
+	 * Read actual data
+	 */
+	for (i = 0; i < count; i++)
+	{
+		if (i == (count - 2))	/* Reached next to last byte, No ACK */
+			__raw_writeb(0xa8, &im->i2c[0].cr);
+		if (i == (count - 1))	/* Reached last byte, STOP */
+			__raw_writeb(0x88, &im->i2c[0].cr);
+
+		/* Read byte of data */
+		buffer[i] = __raw_readb(&im->i2c[0].dr);
+
+		if (i == (count - 1))
+			break;
+		si_wait_i2c();
+	}
+
+	return;
+}
+#endif /* CONFIG_NAND_SPL */
+
+phys_size_t initdram(int board_type)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+	volatile fsl_lbc_t *lbc = &im->im_lbc;
+	u32 msize;
+
+	if ((__raw_readl(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32) im)
+		return -1;
+
+	/* DDR SDRAM - Main SODIMM */
+	__raw_writel(CONFIG_SYS_DDR_BASE & LAWBAR_BAR, &im->sysconf.ddrlaw[0].bar);
+
+	msize = fixed_sdram();
+
+	/* Local Bus setup lbcr and mrtpr */
+	__raw_writel(CONFIG_SYS_LBC_LBCR, &lbc->lbcr);
+	__raw_writel(CONFIG_SYS_LBC_MRTPR, &lbc->mrtpr);
+	sync();
+
+	/* return total bus SDRAM size(bytes)  -- DDR */
+	return (msize * 1024 * 1024);
+}
+
+/*************************************************************************
+ *  fixed sdram init -- reads values from boot sequencer I2C
+ ************************************************************************/
+static long fixed_sdram(void)
+{
+	volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
+	u32 msizelog2, msize = 1;
+#if defined(CONFIG_NAND_SPL)
+	u32 i;
+	const u8 bytecount = 135;
+	u8 buffer[bytecount];
+	u32 addr, data;
+
+	si_read_i2c(0, bytecount, buffer);
+
+	for (i = 18; i < bytecount; i += 7){
+		addr = (u32)buffer[i];
+		addr <<= 8;
+		addr |= (u32)buffer[i + 1];
+		addr <<= 2;
+		data = (u32)buffer[i + 2];
+		data <<= 8;
+		data |= (u32)buffer[i + 3];
+		data <<= 8;
+		data |= (u32)buffer[i + 4];
+		data <<= 8;
+		data |= (u32)buffer[i + 5];
+
+		__raw_writel(data, (u32 *)(CONFIG_SYS_IMMR + addr));
+	}
+
+	sync();
+
+	/* enable DDR controller */
+	__raw_writel((__raw_readl(&im->ddr.sdram_cfg) | SDRAM_CFG_MEM_EN), &im->ddr.sdram_cfg);
+#endif /* (CONFIG_NAND_SPL) */
+
+	msizelog2 = ((__raw_readl(&im->sysconf.ddrlaw[0].ar) & LAWAR_SIZE) + 1);
+	msize <<= (msizelog2 - 20);
+
+	return msize;
+}
diff --git a/qemu/roms/u-boot/board/sheldon/simpc8313/simpc8313.c b/qemu/roms/u-boot/board/sheldon/simpc8313/simpc8313.c
new file mode 100644
index 000000000..31406fa66
--- /dev/null
+++ b/qemu/roms/u-boot/board/sheldon/simpc8313/simpc8313.c
@@ -0,0 +1,150 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ * Copyright (C) Sheldon Instruments, Inc. 2008
+ *
+ * Author: Ron Madrid <info@sheldoninst.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_NAND_SPL
+int checkboard(void)
+{
+	puts("Board: Sheldon Instruments SIMPC8313\n");
+	return 0;
+}
+
+static struct pci_region pci_regions[] = {
+	{
+		bus_start: CONFIG_SYS_PCI1_MEM_BASE,
+		phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
+		size: CONFIG_SYS_PCI1_MEM_SIZE,
+		flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
+		phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
+		size: CONFIG_SYS_PCI1_MMIO_SIZE,
+		flags: PCI_REGION_MEM
+	},
+	{
+		bus_start: CONFIG_SYS_PCI1_IO_BASE,
+		phys_start: CONFIG_SYS_PCI1_IO_PHYS,
+		size: CONFIG_SYS_PCI1_IO_SIZE,
+		flags: PCI_REGION_IO
+	}
+};
+
+void pci_init_board(void)
+{
+	volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+	volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+	struct pci_region *reg[] = { pci_regions };
+
+	/* Enable all 3 PCI_CLK_OUTPUTs. */
+	clk->occr |= 0xe0000000;
+
+	/*
+	 * Configure PCI Local Access Windows
+	 */
+	pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
+	pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
+
+	pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
+	pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
+
+	mpc83xx_pci_init(1, reg);
+}
+
+/*
+ * Miscellaneous late-boot configurations
+ */
+int misc_init_r(void)
+{
+	int rc = 0;
+	immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
+	fsl_lbc_t *lbus = &immap->im_lbc;
+	u32 *mxmr = &lbus->mamr;	/* Pointer to mamr */
+
+	/* UPM Table Configuration Code */
+	static uint UPMATable[] = {
+		/* Read Single-Beat (RSS) */
+		0x0fff0c00, 0x0fffdc00, 0x0fff0c05, 0xfffffc00,
+		0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+		/* Read Burst (RBS) */
+		0x0fff0c00, 0x0ffcdc00, 0x0ffc0c00, 0x0ffc0f0c,
+		0x0ffccf0c, 0x0ffc0f0c, 0x0ffcce0c, 0x3ffc0c05,
+		0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+		0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+		/* Write Single-Beat (WSS) */
+		0x0ffc0c00, 0x0ffcdc00, 0x0ffc0c05, 0xfffffc00,
+		0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+		/* Write Burst (WBS) */
+		0x0ffc0c00, 0x0fffcc0c, 0x0fff0c00, 0x0fffcc00,
+		0x0fff1c00, 0x0fffcf0c, 0x0fff0f0c, 0x0fffcf0c,
+		0x0fff0c0c, 0x0fffcc0c, 0x0fff0c05, 0xfffffc00,
+		0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+		/* Refresh Timer (RTS) */
+		0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+		0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
+		0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
+		/* Exception Condition (EXS) */
+		0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01
+	};
+
+	upmconfig(UPMA, UPMATable, sizeof(UPMATable) / sizeof(UPMATable[0]));
+
+	/* Set LUPWAIT to be active low and enabled */
+	out_be32(mxmr, MxMR_UWPL | MxMR_GPL_x4DIS);
+
+	return rc;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	ft_cpu_setup(blob, bd);
+#ifdef CONFIG_PCI
+	ft_pci_setup(blob, bd);
+#endif
+}
+#endif
+#else /* CONFIG_NAND_SPL */
+void board_init_f(ulong bootflag)
+{
+	NS16550_init((NS16550_t)(CONFIG_SYS_IMMR + 0x4500),
+				CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE);
+	puts("NAND boot... ");
+	init_timebase();
+	initdram(0);
+	relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, (gd_t *)gd,
+				  CONFIG_SYS_NAND_U_BOOT_RELOC);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	nand_boot();
+}
+
+void putc(char c)
+{
+	if (gd->flags & GD_FLG_SILENT)
+		return;
+
+	if (c == '\n')
+		NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), '\r');
+
+	NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), c);
+}
+#endif