1 files changed, 134 insertions, 0 deletions

diff --git a/qemu/roms/u-boot/board/sbc8548/ddr.c b/qemu/roms/u-boot/board/sbc8548/ddr.c
new file mode 100644
index 000000000..24cc776a2
--- /dev/null
+++ b/qemu/roms/u-boot/board/sbc8548/ddr.c
@@ -0,0 +1,134 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 7;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 10;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}
+
+#ifdef CONFIG_SPD_EEPROM
+/*
+ * Workaround for hardware errata.  An i2c address conflict
+ * existed on earlier boards; the workaround moved the DDR
+ * SPD from 0x51 to 0x53.  So we try and read 0x53 1st, and
+ * if that fails, then fall back to reading at 0x51.
+ */
+void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address)
+{
+	int ret;
+
+#ifdef ALT_SPD_EEPROM_ADDRESS
+	if (i2c_address == SPD_EEPROM_ADDRESS) {
+		ret = i2c_read(ALT_SPD_EEPROM_ADDRESS, 0, 1, (uchar *)spd,
+				sizeof(generic_spd_eeprom_t));
+		if (ret == 0)
+			return;		/* Good data at 0x53 */
+		memset(spd, 0, sizeof(generic_spd_eeprom_t));
+	}
+#endif
+	ret = i2c_read(i2c_address, 0, 1, (uchar *)spd,
+				sizeof(generic_spd_eeprom_t));
+	if (ret) {
+		printf("DDR: failed to read SPD from addr %u\n", i2c_address);
+		memset(spd, 0, sizeof(generic_spd_eeprom_t));
+	}
+}
+
+#else
+/*
+ *  fixed_sdram init -- doesn't use serial presence detect.
+ *  Assumes 256MB DDR2 SDRAM SODIMM, without ECC, running at DDR400 speed.
+ */
+phys_size_t fixed_sdram(void)
+{
+	struct ccsr_ddr __iomem *ddr =
+		(struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
+
+	out_be32(&ddr->cs0_bnds,	0x0000007f);
+	out_be32(&ddr->cs1_bnds,	0x008000ff);
+	out_be32(&ddr->cs2_bnds,	0x00000000);
+	out_be32(&ddr->cs3_bnds,	0x00000000);
+
+	out_be32(&ddr->cs0_config,	0x80010101);
+	out_be32(&ddr->cs1_config,	0x80010101);
+	out_be32(&ddr->cs2_config,	0x00000000);
+	out_be32(&ddr->cs3_config,	0x00000000);
+
+	out_be32(&ddr->timing_cfg_3,	0x00000000);
+	out_be32(&ddr->timing_cfg_0,	0x00220802);
+	out_be32(&ddr->timing_cfg_1,	0x38377322);
+	out_be32(&ddr->timing_cfg_2,	0x0fa044C7);
+
+	out_be32(&ddr->sdram_cfg,	0x4300C000);
+	out_be32(&ddr->sdram_cfg_2,	0x24401000);
+
+	out_be32(&ddr->sdram_mode,	0x23C00542);
+	out_be32(&ddr->sdram_mode_2,	0x00000000);
+
+	out_be32(&ddr->sdram_interval,	0x05080100);
+	out_be32(&ddr->sdram_md_cntl,	0x00000000);
+	out_be32(&ddr->sdram_data_init,	0x00000000);
+	out_be32(&ddr->sdram_clk_cntl,	0x03800000);
+	asm("sync;isync;msync");
+	udelay(500);
+
+	#ifdef CONFIG_DDR_ECC
+	  /* Enable ECC checking */
+	  out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | 0x20000000);
+	#else
+	  out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
+	#endif
+
+	return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+}
+#endif