diff options
Diffstat (limited to 'qemu/roms/u-boot/board/mpl/vcma9/lowlevel_init.S')
| -rw-r--r-- | qemu/roms/u-boot/board/mpl/vcma9/lowlevel_init.S | 502 |
1 files changed, 502 insertions, 0 deletions
diff --git a/qemu/roms/u-boot/board/mpl/vcma9/lowlevel_init.S b/qemu/roms/u-boot/board/mpl/vcma9/lowlevel_init.S new file mode 100644 index 000000000..cca9c0c88 --- /dev/null +++ b/qemu/roms/u-boot/board/mpl/vcma9/lowlevel_init.S @@ -0,0 +1,502 @@ +/* + * Memory Setup stuff - taken from blob memsetup.S + * + * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl) and + * Jan-Derk Bakker (J.D.Bakker@its.tudelft.nl) + * + * Modified for MPL VCMA9 by + * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch> + * (C) Copyright 2002, 2003, 2004, 2005 + * + * SPDX-License-Identifier: GPL-2.0+ + */ + + +#include <config.h> +#include <version.h> + + +/* register definitions */ + +#define PLD_BASE 0x28000000 +#define MISC_REG 0x103 +#define SDRAM_REG 0x106 +#define BWSCON 0x48000000 +#define CLKBASE 0x4C000000 +#define LOCKTIME 0x0 +#define MPLLCON 0x4 +#define UPLLCON 0x8 +#define GPIOBASE 0x56000000 +#define GSTATUS1 0xB0 +#define FASTCPU 0x02 + +/* some parameters for the board */ +/* BWSCON */ +#define DW8 (0x0) +#define DW16 (0x1) +#define DW32 (0x2) +#define WAIT (0x1<<2) +#define UBLB (0x1<<3) + +/* BANKSIZE */ +#define BURST_EN (0x1<<7) + +/* BANK0CON 200 */ +#define B0_Tacs_200 0x0 /* 0clk (or 0x1 1clk) */ +#define B0_Tcos_200 0x1 /* 1clk (or 0x2 2clk) */ +#define B0_Tacc_200 0x5 /* 8clk (or 0x6 10clk) */ +#define B0_Tcoh_200 0x0 /* 0clk */ +#define B0_Tcah_200 0x3 /* 4clk (or0x01 1clk) */ +#define B0_Tacp_200 0x0 /* page mode is not used */ +#define B0_PMC_200 0x0 /* page mode disabled */ + +/* BANK0CON 250 */ +#define B0_Tacs_250 0x0 /* 0clk (or 0x1 1clk) */ +#define B0_Tcos_250 0x1 /* 1clk (or 0x2 2clk) */ +#define B0_Tacc_250 0x5 /* 8clk (or 0x7 14clk) */ +#define B0_Tcoh_250 0x0 /* 0clk */ +#define B0_Tcah_250 0x3 /* 4clk (or 0x1 1clk) */ +#define B0_Tacp_250 0x0 /* page mode is not used */ +#define B0_PMC_250 0x0 /* page mode disabled */ + +/* BANK0CON 266 */ +#define B0_Tacs_266 0x0 /* 0clk (or 0x1 1clk) */ +#define B0_Tcos_266 0x1 /* 1clk (or 0x2 2clk) */ +#define B0_Tacc_266 0x6 /* 10clk (or 0x7 14clk) */ +#define B0_Tcoh_266 0x0 /* 0clk */ +#define B0_Tcah_266 0x3 /* 4clk (or 0x1 1clk) */ +#define B0_Tacp_266 0x0 /* page mode is not used */ +#define B0_PMC_266 0x0 /* page mode disabled */ + +/* BANK1CON 200 */ +#define B1_Tacs_200 0x0 /* 0clk (or 0x1 1clk) */ +#define B1_Tcos_200 0x1 /* 1clk (or 0x2 2clk) */ +#define B1_Tacc_200 0x5 /* 8clk (or 0x6 10clk) */ +#define B1_Tcoh_200 0x0 /* 0clk */ +#define B1_Tcah_200 0x3 /* 4clk (or 0x1 1clk) */ +#define B1_Tacp_200 0x0 /* page mode is not used */ +#define B1_PMC_200 0x0 /* page mode disabled */ + +/* BANK1CON 250 */ +#define B1_Tacs_250 0x0 /* 0clk (or 0x1 1clk) */ +#define B1_Tcos_250 0x1 /* 1clk (or 0x2 2clk) */ +#define B1_Tacc_250 0x5 /* 8clk (or 0x7 14clk) */ +#define B1_Tcoh_250 0x0 /* 0clk */ +#define B1_Tcah_250 0x3 /* 4clk (or 0x1 1clk) */ +#define B1_Tacp_250 0x0 /* page mode is not used */ +#define B1_PMC_250 0x0 /* page mode disabled */ + +/* BANK1CON 266 */ +#define B1_Tacs_266 0x0 /* 0clk (or 0x1 1clk) */ +#define B1_Tcos_266 0x1 /* 1clk (or 0x2 2clk) */ +#define B1_Tacc_266 0x6 /* 10clk (or 0x7 14clk) */ +#define B1_Tcoh_266 0x0 /* 0clk */ +#define B1_Tcah_266 0x3 /* 4clk (or 0x1 1clk) */ +#define B1_Tacp_266 0x0 /* page mode is not used */ +#define B1_PMC_266 0x0 /* page mode disabled */ + +/* BANK2CON 200 + 250 + 266 */ +#define B2_Tacs 0x3 /* 4clk */ +#define B2_Tcos 0x3 /* 4clk */ +#define B2_Tacc 0x7 /* 14clk */ +#define B2_Tcoh 0x3 /* 4clk */ +#define B2_Tcah 0x3 /* 4clk */ +#define B2_Tacp 0x0 /* page mode is not used */ +#define B2_PMC 0x0 /* page mode disabled */ + +/* BANK3CON 200 + 250 + 266 */ +#define B3_Tacs 0x3 /* 4clk */ +#define B3_Tcos 0x3 /* 4clk */ +#define B3_Tacc 0x7 /* 14clk */ +#define B3_Tcoh 0x3 /* 4clk */ +#define B3_Tcah 0x3 /* 4clk */ +#define B3_Tacp 0x0 /* page mode is not used */ +#define B3_PMC 0x0 /* page mode disabled */ + +/* BANK4CON 200 */ +#define B4_Tacs_200 0x1 /* 1clk */ +#define B4_Tcos_200 0x3 /* 4clk */ +#define B4_Tacc_200 0x7 /* 14clk */ +#define B4_Tcoh_200 0x3 /* 4clk */ +#define B4_Tcah_200 0x2 /* 2clk */ +#define B4_Tacp_200 0x0 /* page mode is not used */ +#define B4_PMC_200 0x0 /* page mode disabled */ + +/* BANK4CON 250 */ +#define B4_Tacs_250 0x1 /* 1clk */ +#define B4_Tcos_250 0x3 /* 4clk */ +#define B4_Tacc_250 0x7 /* 14clk */ +#define B4_Tcoh_250 0x3 /* 4clk */ +#define B4_Tcah_250 0x2 /* 2clk */ +#define B4_Tacp_250 0x0 /* page mode is not used */ +#define B4_PMC_250 0x0 /* page mode disabled */ + +/* BANK4CON 266 */ +#define B4_Tacs_266 0x1 /* 1clk */ +#define B4_Tcos_266 0x3 /* 4clk */ +#define B4_Tacc_266 0x7 /* 14clk */ +#define B4_Tcoh_266 0x3 /* 4clk */ +#define B4_Tcah_266 0x2 /* 2clk */ +#define B4_Tacp_266 0x0 /* page mode is not used */ +#define B4_PMC_266 0x0 /* page mode disabled */ + +/* BANK5CON 200 */ +#define B5_Tacs_200 0x0 /* 0clk */ +#define B5_Tcos_200 0x3 /* 4clk */ +#define B5_Tacc_200 0x4 /* 6clk */ +#define B5_Tcoh_200 0x3 /* 4clk */ +#define B5_Tcah_200 0x1 /* 1clk */ +#define B5_Tacp_200 0x0 /* page mode is not used */ +#define B5_PMC_200 0x0 /* page mode disabled */ + +/* BANK5CON 250 */ +#define B5_Tacs_250 0x0 /* 0clk */ +#define B5_Tcos_250 0x3 /* 4clk */ +#define B5_Tacc_250 0x5 /* 8clk */ +#define B5_Tcoh_250 0x3 /* 4clk */ +#define B5_Tcah_250 0x1 /* 1clk */ +#define B5_Tacp_250 0x0 /* page mode is not used */ +#define B5_PMC_250 0x0 /* page mode disabled */ + +/* BANK5CON 266 */ +#define B5_Tacs_266 0x0 /* 0clk */ +#define B5_Tcos_266 0x3 /* 4clk */ +#define B5_Tacc_266 0x5 /* 8clk */ +#define B5_Tcoh_266 0x3 /* 4clk */ +#define B5_Tcah_266 0x1 /* 1clk */ +#define B5_Tacp_266 0x0 /* page mode is not used */ +#define B5_PMC_266 0x0 /* page mode disabled */ + +#define B6_MT 0x3 /* SDRAM */ +#define B6_Trcd_200 0x0 /* 2clk */ +#define B6_Trcd_250 0x1 /* 3clk */ +#define B6_Trcd_266 0x1 /* 3clk */ +#define B6_SCAN 0x2 /* 10bit */ + +#define B7_MT 0x3 /* SDRAM */ +#define B7_Trcd_200 0x0 /* 2clk */ +#define B7_Trcd_250 0x1 /* 3clk */ +#define B7_Trcd_266 0x1 /* 3clk */ +#define B7_SCAN 0x2 /* 10bit */ + +/* REFRESH parameter */ +#define REFEN 0x1 /* Refresh enable */ +#define TREFMD 0x0 /* CBR(CAS before RAS)/Auto refresh */ +#define Trp_200 0x0 /* 2clk */ +#define Trp_250 0x1 /* 3clk */ +#define Trp_266 0x1 /* 3clk */ +#define Tsrc_200 0x1 /* 5clk */ +#define Tsrc_250 0x2 /* 6clk */ +#define Tsrc_266 0x3 /* 7clk */ + +/* period=15.6us, HCLK=100Mhz, (2048+1-15.6*100) */ +#define REFCNT_200 489 +/* period=15.6us, HCLK=125Mhz, (2048+1-15.6*125) */ +#define REFCNT_250 99 +/* period=15.6us, HCLK=133Mhz, (2048+1-15.6*133) */ +#define REFCNT_266 0 +/**************************************/ + +.globl lowlevel_init +lowlevel_init: + /* use r0 to relocate DATA read/write to flash rather than memory ! */ + ldr r0, =CONFIG_SYS_TEXT_BASE + ldr r13, =BWSCON + + /* enable minimal access to PLD */ + ldr r1, [r13] /* load default BWSCON */ + orr r1, r1, #(DW8 + UBLB) << 20 /* set necessary CS attrs */ + str r1, [r13] /* set BWSCON */ + ldr r1, =0x7FF0 /* select slowest timing */ + str r1, [r13, #0x18] /* set BANKCON5 */ + + ldr r1, =PLD_BASE + ldr r2, =SETUPDATA + ldrb r1, [r1, #MISC_REG] + sub r2, r2, r0 + tst r1, #FASTCPU /* FASTCPU available ? */ + addeq r2, r2, #SETUPENTRY_SIZE + + /* memory control configuration */ + /* r2 = pointer into timing table */ + /* r13 = pointer to MEM controller regs (starting with BWSCON) */ + add r3, r2, #CSDATA_OFFSET + add r4, r3, #CSDATAENTRY_SIZE +0: + ldr r1, [r3], #4 + str r1, [r13], #4 + cmp r3, r4 + bne 0b + + /* PLD access is now possible */ + /* r3 = SDRAMDATA + /* r13 = pointer to MEM controller regs */ + ldr r1, =PLD_BASE + mov r4, #SDRAMENTRY_SIZE + ldrb r1, [r1, #SDRAM_REG] + /* calculate start and end point */ + mla r3, r4, r1, r3 + add r4, r3, r4 +0: + ldr r1, [r3], #4 + str r1, [r13], #4 + cmp r3, r4 + bne 0b + + /* setup MPLL registers */ + ldr r1, =CLKBASE + ldr r4, =0xFFFFFF + add r3, r2, #4 /* r3 points to PLL values */ + str r4, [r1, #LOCKTIME] + ldmia r3, {r4,r5} + str r5, [r1, #UPLLCON] /* writing PLL register */ + /* !! order seems to be important !! */ + /* a little delay */ + ldr r3, =0x4000 +0: + subs r3, r3, #1 + bne 0b + + str r4, [r1, #MPLLCON] /* writing PLL register */ + /* !! order seems to be important !! */ + /* a little delay */ + ldr r3, =0x4000 +0: + subs r3, r3, #1 + bne 0b + + /* everything is fine now */ + mov pc, lr + + .ltorg +/* the literal pools origin */ + +#define MK_BWSCON(bws1, bws2, bws3, bws4, bws5, bws6, bws7) \ + ((bws1) << 4) + \ + ((bws2) << 8) + \ + ((bws3) << 12) + \ + ((bws4) << 16) + \ + ((bws5) << 20) + \ + ((bws6) << 24) + \ + ((bws7) << 28) + +#define MK_BANKCON(tacs, tcos, tacc, tcoh, tcah, tacp, pmc) \ + ((tacs) << 13) + \ + ((tcos) << 11) + \ + ((tacc) << 8) + \ + ((tcoh) << 6) + \ + ((tcah) << 4) + \ + ((tacp) << 2) + \ + (pmc) + +#define MK_BANKCON_SDRAM(trcd, scan) \ + ((0x03) << 15) + \ + ((trcd) << 2) + \ + (scan) + +#define MK_SDRAM_REFRESH(enable, trefmd, trp, tsrc, cnt) \ + ((enable) << 23) + \ + ((trefmd) << 22) + \ + ((trp) << 20) + \ + ((tsrc) << 18) + \ + (cnt) + +SETUPDATA: + .word 0x32410002 + /* PLL values (MDIV, PDIV, SDIV) for 250 MHz */ + .word (0x75 << 12) + (0x01 << 4) + (0x01 << 0) + /* PLL values for USB clock */ + .word (0x48 << 12) + (0x03 << 4) + (0x02 << 0) + + /* timing for 250 MHz*/ +0: + .equiv CSDATA_OFFSET, (. - SETUPDATA) + .word MK_BWSCON(DW16, \ + DW32, \ + DW32, \ + DW16 + WAIT + UBLB, \ + DW8 + UBLB, \ + DW32, \ + DW32) + + .word MK_BANKCON(B0_Tacs_250, \ + B0_Tcos_250, \ + B0_Tacc_250, \ + B0_Tcoh_250, \ + B0_Tcah_250, \ + B0_Tacp_250, \ + B0_PMC_250) + + .word MK_BANKCON(B1_Tacs_250, \ + B1_Tcos_250, \ + B1_Tacc_250, \ + B1_Tcoh_250, \ + B1_Tcah_250, \ + B1_Tacp_250, \ + B1_PMC_250) + + .word MK_BANKCON(B2_Tacs, \ + B2_Tcos, \ + B2_Tacc, \ + B2_Tcoh, \ + B2_Tcah, \ + B2_Tacp, \ + B2_PMC) + + .word MK_BANKCON(B3_Tacs, \ + B3_Tcos, \ + B3_Tacc, \ + B3_Tcoh, \ + B3_Tcah, \ + B3_Tacp, \ + B3_PMC) + + .word MK_BANKCON(B4_Tacs_250, \ + B4_Tcos_250, \ + B4_Tacc_250, \ + B4_Tcoh_250, \ + B4_Tcah_250, \ + B4_Tacp_250, \ + B4_PMC_250) + + .word MK_BANKCON(B5_Tacs_250, \ + B5_Tcos_250, \ + B5_Tacc_250, \ + B5_Tcoh_250, \ + B5_Tcah_250, \ + B5_Tacp_250, \ + B5_PMC_250) + + .equiv CSDATAENTRY_SIZE, (. - 0b) + /* 4Mx8x4 */ +0: + .word MK_BANKCON_SDRAM(B6_Trcd_250, B6_SCAN) + .word MK_BANKCON_SDRAM(B7_Trcd_250, B7_SCAN) + .word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_250, Tsrc_250, REFCNT_250) + .word 0x32 + BURST_EN + .word 0x30 + .word 0x30 + .equiv SDRAMENTRY_SIZE, (. - 0b) + + /* 8Mx8x4 */ + .word MK_BANKCON_SDRAM(B6_Trcd_250, B6_SCAN) + .word MK_BANKCON_SDRAM(B7_Trcd_250, B7_SCAN) + .word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_250, Tsrc_250, REFCNT_250) + .word 0x32 + BURST_EN + .word 0x30 + .word 0x30 + + /* 2Mx8x4 */ + .word MK_BANKCON_SDRAM(B6_Trcd_250, B6_SCAN) + .word MK_BANKCON_SDRAM(B7_Trcd_250, B7_SCAN) + .word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_250, Tsrc_250, REFCNT_250) + .word 0x32 + BURST_EN + .word 0x30 + .word 0x30 + + /* 4Mx8x2 */ + .word MK_BANKCON_SDRAM(B6_Trcd_250, B6_SCAN) + .word MK_BANKCON_SDRAM(B7_Trcd_250, B7_SCAN) + .word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_250, Tsrc_250, REFCNT_250) + .word 0x32 + BURST_EN + .word 0x30 + .word 0x30 + + .equiv SETUPENTRY_SIZE, (. - SETUPDATA) + + .word 0x32410000 + /* PLL values (MDIV, PDIV, SDIV) for 200 MHz (Fout = 202.8MHz) */ + .word (0xA1 << 12) + (0x03 << 4) + (0x01 << 0) + /* PLL values for USB clock */ + .word (0x48 << 12) + (0x03 << 4) + (0x02 << 0) + + /* timing for 200 MHz and default*/ + .word MK_BWSCON(DW16, \ + DW32, \ + DW32, \ + DW16 + WAIT + UBLB, \ + DW8 + UBLB, \ + DW32, \ + DW32) + + .word MK_BANKCON(B0_Tacs_200, \ + B0_Tcos_200, \ + B0_Tacc_200, \ + B0_Tcoh_200, \ + B0_Tcah_200, \ + B0_Tacp_200, \ + B0_PMC_200) + + .word MK_BANKCON(B1_Tacs_200, \ + B1_Tcos_200, \ + B1_Tacc_200, \ + B1_Tcoh_200, \ + B1_Tcah_200, \ + B1_Tacp_200, \ + B1_PMC_200) + + .word MK_BANKCON(B2_Tacs, \ + B2_Tcos, \ + B2_Tacc, \ + B2_Tcoh, \ + B2_Tcah, \ + B2_Tacp, \ + B2_PMC) + + .word MK_BANKCON(B3_Tacs, \ + B3_Tcos, \ + B3_Tacc, \ + B3_Tcoh, \ + B3_Tcah, \ + B3_Tacp, \ + B3_PMC) + + .word MK_BANKCON(B4_Tacs_200, \ + B4_Tcos_200, \ + B4_Tacc_200, \ + B4_Tcoh_200, \ + B4_Tcah_200, \ + B4_Tacp_200, \ + B4_PMC_200) + + .word MK_BANKCON(B5_Tacs_200, \ + B5_Tcos_200, \ + B5_Tacc_200, \ + B5_Tcoh_200, \ + B5_Tcah_200, \ + B5_Tacp_200, \ + B5_PMC_200) + + /* 4Mx8x4 */ + .word MK_BANKCON_SDRAM(B6_Trcd_200, B6_SCAN) + .word MK_BANKCON_SDRAM(B7_Trcd_200, B7_SCAN) + .word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_200, Tsrc_200, REFCNT_200) + .word 0x32 + BURST_EN + .word 0x30 + .word 0x30 + + /* 8Mx8x4 */ + .word MK_BANKCON_SDRAM(B6_Trcd_200, B6_SCAN) + .word MK_BANKCON_SDRAM(B7_Trcd_200, B7_SCAN) + .word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_200, Tsrc_200, REFCNT_200) + .word 0x32 + BURST_EN + .word 0x30 + .word 0x30 + + /* 2Mx8x4 */ + .word MK_BANKCON_SDRAM(B6_Trcd_200, B6_SCAN) + .word MK_BANKCON_SDRAM(B7_Trcd_200, B7_SCAN) + .word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_200, Tsrc_200, REFCNT_200) + .word 0x32 + BURST_EN + .word 0x30 + .word 0x30 + + /* 4Mx8x2 */ + .word MK_BANKCON_SDRAM(B6_Trcd_200, B6_SCAN) + .word MK_BANKCON_SDRAM(B7_Trcd_200, B7_SCAN) + .word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_200, Tsrc_200, REFCNT_200) + .word 0x32 + BURST_EN + .word 0x30 + .word 0x30 + + .equiv SETUPDATA_SIZE, (. - SETUPDATA) |